A single-board video codec using video image signal processors

This paper discusses a newly developed single-board video codec using Video Image Signal Processors (VISPs). The codec has both a CCITT H.261 mode and a proprietary mode. Two VISPs, one for encoding and one for decoding, are used. The board size is 210 by 295 mm, the maximum frame rate is about 7.5 f/s, and the picture size is 180 by 144 pels.     

Behaviour of Cohesive Powders in a Powder‐Particle Spouted Bed

Behaviour of cohesive powders in a powder‐particle spouted Bed (PPSB) has been investigated under several operating variables and solids properties. The elutriation rate constant based on the hold‐up of fine powders in the bed decreased with a decrease in the size of fine powders, and with an increase in the size of coarse particles under a constant superficial gas velocity. This finding is quite different from the elutriation phenomena of particles more than 100 µm in size. Moreover, the mean residence time of fine powders increased with a decrease in the superficial gas velocity and the size of fine powders, and decreased with a decrease in the size of coarse particles.     

Compositional Engineering for Thermally Stable,Highly Efficient Perovskite Solar Cells Exceeding 20% Power Conversion Efficiency with 85 °C/85% 1000 h Stability

Perovskite solar cells have received great attention because of their rapid progress in efficiency, with a present certified highest efficiency of 23.3%. Achieving both high efficiency and high thermal stability is one of the biggest challenges currently limiting perovskite solar cells because devices displaying stability at high temperature frequently suffer from a marked decrease of efficiency. In this report, the relationship between perovskite composition and device thermal stability is examined. It is revealed that Rb can suppress the growth of PbI₂ even under PbI₂‐rich conditions and decreasing the Br ratio in the perovskite absorber layer can prevent the generation of unwanted RbBr‐based aggregations. The optimized device achieved by engineering perovskite composition exhibits 92% power conversion efficiency retention in a stress test conducted at 85 °C/85% relative humidity (RH) according to an international standard (IEC 61215) while exceeding 20% power conversion efficiency (certified efficiency of 20.8% at 1 cm²). These results reveal the great potential for the practical use of perovskite solar cells in the near future.     

Rapid Preparation of Lead Titanate Sputtering Target Using Spark-Plasma Sintering

PbTiO₃ sputtering targets 8 cm in diameter were prepared using spark-plasma sintering (SPS) for relatively short periods, ∼2 min. Submicrometer-sized PbTiO₃ powders with a relatively large size distribution were densified to ∼86% of the theoretical X-ray density using the SPS process. In contrast, large-sized (8 cm in diameter) ceramics could not be prepared from starting powders with a relatively narrow particle-size distribution. Formation of cracks in the large PbTiO₃ targets was observed when samples were prepared under higher pressures (>50 MPa) or at higher temperatures (>900°C). Crack formation was attributed to unrelaxed internal stress originating from lower pore contents and from an inhomogeneous distribution of cations in the ceramics prepared under these conditions.     

Thermal diffusivity measurement of 2.25Cr-1Mo steel with internal friction

In this work, the internal friction of 2.25Cr-1Mo steel measured on a dynamic mechanical analyzer (DMA) was used to evaluate its thermal diffusivity at elevated temperatures. With the dual cantilever clamp, the internal friction of 2.25Cr-1Mo steel at high temperatures was obtained, which was mainly composed of the thermoelastic relaxation with a peak of 15 Hz and the broad spectrum of relaxation processes especially at low frequencies. According to the deconvolution of these results, the thermoelastic internal friction of 2.25Cr-1Mo steel at high temperatures was achieved. Then, the thermal diffusivity of 2.25Cr-1Mo steel at high temperatures was quantitatively estimated, which confirmed the validity of present method.     

Deformation near parallel cracks close to interface in bonded dissimilar plate

Tensile tests are carried out by using rectangular plate specimens extracted from the explosion clad plate. Artificial parallel cracks are made perpendicularly to the explosive interface in each specimen. When a tensile load is applied perpendicularly to the crack plane, strain, plastic deformation near cracks and crack opening displacement are examined by experiments as well as elasto-plastic finite element analysis. The effects of the material inhomogeneity, the change of material characteristics, the residual stress and the interaction between parallel cracks on the deformation behavior are revealed. The plastic zone around parallel cracks, at relatively low applied stress level, grows mainly ahead of and between two cracks. The interaction between parallel cracks on the crack opening displacement can be explained from the square of stress intensity factor at the low applied stress level and from the plastic deformation at the high applied stress level.     

Analysis of the Circulating Tumor Cell Capture Ability of a Slit Filter-Based Method in Comparison to a Selection-Free Method in Multiple Cancer Types

Circulating tumor cells (CTCs) are a promising biomarker for cancer liquid biopsy. To evaluate the CTC capture bias and detection capability of the slit filter-based CTC isolation platform (CTC-FIND), we prospectively compared it head to head to a selection-free platform (AccuCyte^®-CyteFinder^® system). We used the two methods to determine the CTC counts, CTC positive rates, CTC size distributions, and CTC phenotypes in 36 patients with metastatic cancer. Between the two methods, the median CTC counts were not significantly different and the total counts were correlated (r = 0.63, p < 0.0001). The CTC positive rate by CTC-FIND was significantly higher than that by AccuCyte^®-CyteFinder^® system (91.7% vs. 66.7%, p < 0.05). The median diameter of CTCs collected by CTC-FIND was significantly larger (13.0 μm, range 5.2–52.0 vs. 10.4 μm, range 5.2–44.2, p < 0.0001). The distributions of CTC phenotypes (CK+EpCAM+, CK+EpCAM− or CK−EpCAM+) detected by both methods were similar. These results suggested that CTC-FIND can detect more CTC-positive cases but with a bias toward large size of CTCs.