Synthesis,characterization, and supercapacitor studies of manganese (IV) oxide nanowires

One-dimensional manganese (IV) oxide (MnO₂) (～20 nm in average diameter) were synthesized by cathodic electrodeposition and heat treatment. The mechanism of electrodeposition and nanowire formation were discussed. The product was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR). Nanowires with varying lengths and diameters were found in TEM and SEM images of the sample. The results of N₂ adsorption–desorption analysis indicated that the BET surface area of the MnO₂ nanowires was 157 m² g^?1 and the pore size distributions were 2.5 and 4.5 nm. The electrochemical performances of the prepared MnO₂ as an electrode material for supercapacitors were evaluated by cyclic voltammetry and galvanostatic charge/discharge measurements in a solution of 0.5 M Na₂SO₄. The higher specific capacitance of 318 F g^?1 and good capacity retention of 86% were achieved after 1000 charge–discharge cycles had been observed for the MnO₂ nanowires electrode.     

Adaptive double recycling folded cascode amplifier

Analog Integrated Circuits and Signal Processing - A new structure for improving the performance of recycling folded cascode (RFC) operational transconductance amplifier (OTA) is presented. The...     

Lossless,Passive Transportation of Low Surface Tension Liquids Induced by Patterned Omniphobic Liquidlike Polymer Brushes

Surfaces enabling directional liquid transportation are of great interest for a wide range of applications such as water collection, microfluidics, and heat transfer systems. Surfaces capable of lossless, long-range passive transportation of low surface tension (LST) liquids using wettability patterned, liquidlike coatings with minimal contact angle hysteresis are reported. Lossless LST droplet travel distances over 150 mm are achieved, enabled by a two-phase transportation mechanism: morphological transformation from a bulge to a channel shape, followed by directional transportation along the asymmetrical wedge-shaped channel. The developed surfaces can split, merge, and precisely transport various low-surface tension liquids, including alcohols, alkanes, and solvents. The developed transportation strategy can also enhance LST liquid dropwise condensation through continuous removal of the condensate, even on horizontally positioned surfaces without the assistance of gravity.     

UNICORE 6 — Recent and Future Advancements

UNICORE is a European Grid Technology with more than 10 years of history. Originating from the Supercomputing domain, the latest version UNICORE 6 has turned into a general-purpose Grid technology that follows established standards and offers a rich set of features to its users. The paper starts with an architectural insight into UNICORE 6, highlighting the workflow features, standards and the different clients. Next, the current state of advancement is presented by describing recent developments. The paper closes with an outlook on future planned developments.     

Multi-Stage CMOS OTA Frequency Compensation: Genetic algorithm approach

Multistage amplifiers have become appropriate choices for high-speed electronics and data conversion. Because of the large number of high-impedance nodes, frequency compensation has become the biggest challenge in the design of multistage amplifiers. The new compensation technique in this study uses two differential stages to organize feedforward and feedback paths. Five Miller loops and a 500-pF load capacitor are driven by just two tiny compensating capacitors, each with a capacitance of less than 10 pF. The symbolic transfer function is calculated to estimate the circuit dynamics and HSPICE and TSMC 0.18 μm. CMOS technology is used to simulate the proposed five-stage amplifier. A straightforward iterative approach is also used to optimize the circuit parameters given a known cost function. According to simulation and mathematical results, the proposed structure has a DC gain of 190 dB, a gain bandwidth product of 15 MHz, a phase margin of 89°, and a power dissipation of 590 μW.     

Recapillarity: Electrochemically Controlled Capillary Withdrawal of a Liquid Metal Alloy from Microchannels

This paper describes the mechanistic details of an electrochemical method to control the withdrawal of a liquid metal alloy, eutectic gallium indium (EGaIn), from microfluidic channels. EGaIn is one of several alloys of gallium that are liquid at room temperature and form a thin (nm scale) surface oxide that stabilizes the shape of the metal in microchannels. Applying a reductive potential to the metal removes the oxide in the presence of electrolyte and induces capillary behavior; we call this behavior “recapillarity” because of the importance of electrochemical reduction to the process. Recapillarity can repeatably toggle on and off capillary behavior by applying voltage, which is useful for controlling the withdrawal of metal from microchannels. This paper explores the mechanism of withdrawal and identifies the applied current as the key factor dictating the withdrawal velocity. Experimental observations suggest that this current may be necessary to reduce the oxide on the leading interface of the metal as well as the oxide sandwiched between the wall of the microchannel and the bulk liquid metal. The ability to control the shape and position of a metal using an applied voltage may prove useful for shape reconfigurable electronics, optics, transient circuits, and microfluidic components.     

Signal Detection Performance of Overlapped FFT Scheme with Additional Frames Consisting of Non-continuous Samples in Indoor Environment

Overlapped FFT has been proposed as a signal detection scheme in dynamic spectrum access to reduce the variance of the noise and improve the detection probability. However, the improvement of the detection probability in the conventional overlapped FFT is bounded with the upper limit of the overlap ratio. This paper proposes a new overlapped FFT scheme using additional frames. In the proposed scheme, in addition to the original FFT frames, new frames that consist of multiple subframes with non-continuous samples are constructed and included. It can realize the increase of the number of the FFT frames and the improvement of the detection probability compared with the conventional scheme. Numerical results through computer simulation show that the proposed scheme improves the detection probability by up to 0.07. On indoor channel models the proposed scheme also improves the detection probability. In addition, it is clarified that as the delay spread increases the detection probability reduces due to the correlation between the frames.     

The Einstein relation for degenerate semiconductors with nonuniformband structures

Modification of the Einstein equation for semiconductors with nonparabolic energy bands and doped nonuniformly with impurity atoms is suggested. The suggestion is based on a new approximation of the Fermi-Dirac integral of order 1/2, namely, F_1/2(η_n), where η_n is the reduced Fermi level for electrons. The relation reduces to that for semiconductors with parabolic energy bands and doped uniformly with impurity atoms under appropriate boundary conditions. A comparison of the calculated and exact results for F_1/2(η) is found to be very encouraging     

Arbitrary dual-band unequal Wilkinson power divider based on negative refractive index transmission lines

This paper focused on the application of negative refractive index transmission line (NRI-TL) in dual-band unequal Wilkinson power divider (WPD) with controllable frequency and power dividing ratio. Theory and design procedure of the dual-band NRI-TL are presented in details. For demonstration, two dual-band unequal Wilkinson power dividers (WPDs) with power dividing ratio of 2 : 1 and operating frequencies of 0.9 and 1.8 GHz are designed, fabricated and tested. The first unequal divider is based on 2-stage NRI-TLs and the second one is based on 4-stage NRI-TLs. In addition, these two types of NRI-TLs are presented to demonstrate that by increasing the number of NRI-TL unit-cells the phase response of the NRI-TLs converge to the desired characteristic. The good agreement between measured and simulated results confirmed the design concept and derived closed-form design equations. Measurements show that the first divider has 18.37% and 21.86% relative bandwidths and the second one has 33.52% and 29.12% relative bandwidths at 0.9 and 1.8 GHz, respectively. The design concept of this paper can be extended to equal dual-band power dividers with arbitrary frequency ratio.     

Interpolation techniques for building a continuous map from discrete wireless sensor network data

Wireless sensor networks (WSNs) typically gather data at a discrete number of locations. However, it is desirable to be able to design applications and reason about the data in more abstract forms than in points of data. By bestowing the ability to predict inter‐node values upon the network, it is proposed that it will become possible to build applications that are unaware of the concrete reality of sparse data. This interpolation capability is realised as a service of the network. In this paper, the ‘map’ style of presentation has been identified as a suitable sense data visualisation format. Although map generation is essentially a problem of interpolation between points, a new WSN service, called the map generation service, which is based on a Shepard interpolation method, is presented. A modified Shepard method that aims to deal with the special characteristics of WSNs is proposed. It requires small storage, can be localised and integrates the information about the application domain to further reduce the map generation cost and improve the mapping accuracy. Empirical analysis has shown that the map generation service is an accurate, a flexible and an efficient method. Copyright © 2011 John Wiley & Sons, Ltd.