Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

High-gain pseudomorphic InGaAs base ballistic hot-electron device

A high-gain ballistic hot-electron device is described. The GaAs-AlGaAs heterostructure device, with a 21-mm-thick pseudomorphic In _0.12Ga_0.88As base, had a current gain of 27 at 77 K and 41 at 4.2 K. As characteristically seen in ballistic devices, transfer into the L valley limited the maximum gain. The Γ-L valley separation in the strained In_0.12Ga_0.88As was estimated to be about 380 meV     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Filled Fibrous Sorbents Modified with Transition Metal Ferro- and Ferricyanides for Recovery of Americium and Rare-Earth Metals

Filled fibrous sorbents modified with transition metal ferro- and ferricyanides capable to recover americium(III) and rare-earth metals(III) from nitric acid solutions were prepared. The most complete and rapid recovery is attained on complex-forming and cation-exchange sorbents (as filled fibrous materials) saturated with nickel ions. The sorbents are characterized by good kinetic properties and can be used for recovery of the above metals.     

Assessment of a Flexible Architecture for Distributed Control*

Production pipelines of manufactory industries present several machines and robots in which the movements of interpolated axes are managed by computerized numerical controls (CNCs). These are typically synchronized with several other simpler actuators along the pipeline of production. CNCs have to be flexible, easily expandable, and reusable, when pipelines of production are frequently reconfigured to realize different arranged pipelines with different technical requirements. In this paper, the assessment of a flexible CNC for such reconfigurable pipelines is presented. The analysis has been focused on defining objective metrics that can be applied for assessing performance and feasibility of distributed controls for pipelines. The method proposed has been applied on the distributed control architecture defined in the MUPAAC ESPRIT HPCN (Multi Processor Architecture for Automatic Control, High Performance Computer Networking of the European Commission). MUPAAC architecture and prototype has been assessed in order to identify the critical configurations and the limits of the architecture.     

Influence of generator load conditions on third-harmonic voltages in generator stator winding

The influence of changes in load conditions of the generator-transformer unit on the operating conditions of the 100% ground-fault protection of the generator stator winding based on the third-harmonic voltages was analyzed. The analyzed stator ground-fault protection system is by ratio of the voltages third harmonic in generator neutral and at the generator terminals. The third-harmonic voltages were determined on the base of the experimental tests (measurements) run in real conditions at changes in active and reactive load conditions of the generator. It was found that mainly the generator active load influences the voltage feeding the measuring element of ground-fault protection. Therefore, determining operating conditions of ground-fault protection the influence of the generator active and reactive load should be deeply considered. This can ensure the proper operation of the ground-fault protection based on the voltage third harmonics in the whole range of the changes in generator load. Considering the influence of changes in generator load on the third-harmonic voltages (feeding measuring element of the protection system) will allow eliminating irregular generator tripping as a result of unselective operation of these protections.     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

Ultrasonic treatment restores the photoelectric parameters of silicon solar cells degraded under the action of <Superscript>60</Superscript>Co gamma radiation

The photoelectric parameters of silicon solar cells degraded under the action of ⁶⁰Co gamma-radiation can be partly restored using an ultrasonic treatment (UST). The growth of the maximum output power of solar cells after the UST is related to a redistribution of the radiation defects and an increase in the homogeneity of a semiconductor crystal structure.     

Power Distribution Fault Cause Identification With Imbalanced Data Using the Data Mining-Based Fuzzy Classification E-Algorithm

Power distribution systems have been significantly affected by many outage-causing events. Good fault cause identification can help expedite the restoration procedure and improve the system reliability. However, the data imbalance issue in many real-world data sets often degrades the fault cause identification performance. In this paper, the E-algorithm, which is extended from the fuzzy classification algorithm by Ishibuchi to alleviate the effect of imbalanced data constitution, is applied to Duke Energy outage data for distribution fault cause identification. Three major outage causes (tree, animal, and lightning) are used as prototypes. The performance of E-algorithm on real-world imbalanced data is compared with artificial neural network. The results show that the E-algorithm can greatly improve the performance when the data are imbalanced