A framework for the characterization and verification of embedded phase-locked loops

With the increasing use of phase-locked loops (PLLs) embedded in FPGAs, ASICs, and system-on-chip (SOC), there is a growing need for methods to verify their operation. This paper describes a general and organized list that includes tests for lock, jitter, stability, and modulation response. The list is offered as a guide to the verification and testing of an embedded PLL. For that reason, it is presented in such a way as to allow the reader to determine the extent to which the verification will be carried out. The tests are covered from the easiest to the most complicated to perform, with the amount of information gathered increasing along with the complexity of the test.     

A Dempster–Shafer Based Tit-for-Tat Strategy to Regulate the Cooperation in VANET Using QoS-OLSR Protocol

In this paper, we address the problem of cooperation among vehicles in VANET using QoS-OLSR protocol in the presence of selfish nodes. QoS-OLSR is a proactive protocol that considers the Quality of Service (QoS) of the nodes while electing the cluster-heads and selecting the Multi-Point Relay (MPRs) nodes. Cluster-heads and MPRs might misbehave on the roads by over-speeding or under-speeding. Classical and generous Tit-for-Tats are proposed to analyze the interaction among vehicles. However, both strategies are not able to enforce the cooperation due the fact that they (1) count on individual watchdogs monitoring, (2) rely on the node-to-node cooperation decision, (3) and ignore the high mobility and packet collisions. Therefore, we propose a Dempster–Shafer based Tit-for-Tat strategy that is able to improve the decision and regulate the cooperation in the vehicular network. This is done by (1) launching a cooperative watchdogs monitoring, (2) correlating the observations of the different watchdogs using Dempster–Shafer theory, and (3) propagating the decisions among clusters. Thereafter, we compare the Dempster–Shafer based strategy with several strategies derived from the original Tit-for-Tat. Simulation results prove that the Dempster–Shafer based strategy is able to maintain the survivability of the vehicular network in the presence of high mobility and packet collisions with minimal time and overhead.     

Economical evaluation of electricity generation considering externalities

The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle–natural gas fired system. A photovoltaic system still uses comparatively expensive technology for electricity generation; even when external costs are considered the capital cost of photovoltaic needs to be reduced by about 60% in order to be economically competitive.     

Mesure de coefficients de convection par méthode impulsionnelle—influence de la perturbation de la couche limiteMeasurement of the convective heat coefficients by the pulsed method—influence of the boundary-layer perturbation

We present here some elements in order to improve the non-destructive procedures for the measurement of the local heat transfer coefficient between a plate uniformly heated and an air-flow. We use the pulsed photothermal method which consists of analysing the transient temperature on the front face of a wall, initially subjected to a convective flow, after a sudden deposit of luminous energy. For the examination of the experimental thermograms, two models are used: in the first one the heat coefficient is assumed to remain constant during the pulsed experiment, and we take into account its variation in time in the second one. The temporal variation law of the heat transfer coefficient used in the second model is obtained by extension of the differential method to the unsteady laminar boundary-layer due to a finite duration excitation. We compare the results of the two models in transient state with those given in steady state by multi-layered heat flux sensor.     

Non-linear optical and electrical properties of ZnO doped Ni Thin Films obtained using spray ultrasonic technique

In the present study zinc oxide doped Nickel thin films (ZnO:Ni) were deposited on glass substrates using a chemical spray ultrasonic technique. The effect of Ni concentration on the structural, electrical, optical, and non-linear optical (NLO) properties of the ZnO:Ni thin films was investigated. The films were analyzed using X-ray diffraction (XRD), profilometry and optical transmittance. A polycrystalline structure with a preferential growth along the ZnO (002) plane was found, the optical transmittance was found to be higher than 80% and the band gap (E_g) varied from 3.19 to 3.27 eV. The value of the electrical conductivity was found. Moreover, the effective non-linear quadratic and cubic electronic susceptibilities of thin film samples were determined by the SHG and THG techniques, working at 1064 nm.     

Investigation of Natural Radioactivity in Wadi El Reddah Stream Sediments and Its Radiological Implications

Radiochemistry - Wadi El Reddah has radiation exposure due to the presence of different types of complexed rocks along with a huge sector of Hammamat sedimentary rocks, monzongranites of Gabal El...     

Synthesis and characterization of cellulose triacetate and poly(ethylene imine) membranes containing a polyether macrobicyclic: Their application to the separation of copper(II) and silver(I) ions

A cellulose triacetate (CTA)–poly(ethylene imine) (PEI) membrane containing a polyether macrobicyclic (cryptand) as a carrier and 2‐nitrophenyloctyl ether (NPOE) as a plasticizer was prepared. The CTA–PEI–cryptand–NPOE membrane was characterized with chemical techniques as well as Fourier transform infrared, X‐ray diffraction, differential scanning calorimetry, and scanning electron microscopy. The permeation of silver and copper ions through the CTA–PEI–cryptand–NPOE membrane was comparable to that through a supported liquid membrane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1401–1410, 2004     

Denitrogenation of carbazole by a novel strain Bacillus Clausii BS1 isolated from Egyptian Coke

In this study, an effective enrichment technique was applied to isolate different bacterial strains with capabilities to denitrogenate carbazole (CAR), as a model compound for nitrogenous polyaromatic hydrocarbons (NPAHs). Twenty-four different CAR-denitrogenating bacterial strains were isolated from mineral coke samples. From all, a Gram +ve bacterial isolate designated BS1 showed a higher biodenitrogenation (BDN) efficiency relevant to the well-known biodenitrogenating bacterium strain Pseudomonas resinovorans CA10, recording 77.15 and 60.66% removal of 1000 ppm CAR with the production of 119.79 and 102.43 ppm anthranilic acid, and 121.19 and 90.33 ppm catechol, as by-products, respectively. BS1 was identified by 16S rDNA gene sequence analysis to be Bacillus clausii BS1 (NCBI GenBank Accession no. KF985981) with a similarity of 99.14%. The CAR-BDN pathway was also elucidated using high-performance liquid chromatography (HPLC) and gas chromatography mass spectrometry analysis (GC/MS), which proved further metabolism of catechol to muconic acid.     

A meta-modelling framework for knowledge consistency in collaborative design

The design of complex system requires a lot of interactions between experts and then between numerous Computer Aided X software (CAX) (where X can be Design (CAD), Engineering (CAE), Manufacturing (CAM), etc.). In order to improve the consistency of the whole system design and the related data and information, knowledge crossing the expertises must be tracked and formalized regarding a shared reference. That means that instead of defining a large reference models to which each expert refers to, a light collaborative model is defined enabling to connect data from each expert model to adhoc data from other expert models, following the least commitment principle. In this topic, a new meta-model is proposed in a Model-Driven Engineering approach to manage the integration of heterogeneous experts’ knowledge models in a collaborative process. The structure of the proposed knowledge meta-model is defined taking into account the complexity of knowledge definition and the properties of its components. This meta-model is split in a meta-model of data on one hand and a Collaboration Meta-Model in the other hand, to represent the distinction between the core concepts of knowledge and additional elements serving to represent the relation between these concepts, and between concepts of heterogeneous experts’ models. The proposed meta-model is illustrated on an industrial case study to highlight the way to put it in use, and its interests to enable collaboration between experts throughout the design process.     

Decentralized Networked Control System Design Using Takagi-Sugeno (TS) Fuzzy Approach

This paper proposes a new method for control of continuous large-scale systems where the measures and control functions are distributed on calculating members which can be shared with other applications and connected to digital network communications.At first, the nonlinear large-scale system is described by a Takagi-Sugeno(TS) fuzzy model. After that, by using a fuzzy LyapunovKrasovskii functional, sufficient conditions of asymptotic stability of the behavior of the decentralized networked control system(DNCS),are developed in terms of linear matrix inequalities(LMIs). Finally, to illustrate the proposed approach, a numerical example and simulation results are presented.