The microstructure of Cu films deposited by the self-ion assisted technique

The microstructures of Cu films deposited by the self-ion assisted, partially ionized beam (PIB) deposition technique under two different accelerating potentials, 0 KeV and 6 KeV, are compared. The 6 KeV film shows a bimodal (111) fiber and (100) fiber texture with an abundance of twin boundaries and a relatively large average grain size with a typical lognormal distribution. The 0 KeV film consists of small, mostly (111) oriented grains with islands of abnormally large (100) grains. The controlling factors for the abnormal growth of the (100) grains are discussed in relation to the observed microstructures, showing that all factors necessary for abnormal (100) growth are present in the films.     

Reliability prediction models to support conceptual design

During the early stages of conceptual design, the ability to predict reliability is very limited. Without a prototype to test in a lab environment or without field data, component failure rates and system reliability performance are usually unknown. A popular method for early reliability prediction is to develop a computer model for the system. However, most of these models are extremely specific to an individual system or industry. This paper presents three general procedures (using both simulation and analytic solution techniques) for predicting system reliability and average mission cost. The procedures consider both known and unknown failure rates and component-level and subsystem-level analyzes. The estimates are based on the number of series subsystems and redundant (active or stand-by) components for each subsystem. The result is a set of approaches that engineers can use to predict system reliability early in the system-design process. Software was developed (and is discussed in this paper) that facilitates the application of the simulation-based techniques. For the specific type of system and mission addressed in this paper, the analytic approach is superior to the simulation-based prediction models. However, all three approaches are presented for two reasons: (1) to convey the development process involved with building these prediction tools; and (2) the simulation-based approaches are of greater value as the research is extended to consider more complex systems and scenarios     

Correction to "How to model reliability-growth when times of designmodifications are known"

A typographical error in the log-likelihood in the paper by N. Ebrahimi (see ibid., vol.45, p.54-8, 1996) is corrected     

用仿真工具优化车辆动力系统(一)

在本文的第一部分，介绍了一种理想的车辆动力系统的计算机辅助开发过程。它显示了现代仿真技术在产品持续发展过程中的作用，该技术采用硬件回路作非在线的仿真，并通过现代化的试验手段对车辆进行匹配。特别重要的是提供了将电控变速器和发动机控制单元综合的可能性。接着是在线仿真在诸如发动机和变速器模式方面的应用和发展，它是上述开发过程的基础。根据上述的方法论，本文论述了仿真技术已取得的成绩和将来的应用可能性。     

Integrated chaos generators

This paper surveys the different design issues, from mathematical model to silicon, involved in the design of analog CMOS integrated circuits for the generation of chaotic behavior     

用于制导弹药的自适应自动驾驶仪设计

传统制导弹药自动驾驶仪的设计要求精确的气动模型,并依赖于变增益(gainschedule),以说明系统的非线性.本文给出了一种简化自动驾驶仪设计程序的方法:在单一飞行条件下设计逆控制器,将逆控制器与在线神经网络组合,以说明因近似逆引起的误差,这样减少了大量设计程序及精确的气动数据.这些数据在大攻角或其它情况下很重要,因为这些领域中的空气动力特征变得高度非线性化.研究发现:逆的选择在其实现的过程中很重要,所以详细讨论.最后,给出该方法在非线性6自由度制导弹药中的模拟结果.     

Modeling of laser keyhole welding: Part I. mathematical modeling,numerical methodology,role of recoil pressure,multiple reflections,and free surface evolution

A three-dimensional laser-keyhole welding model is developed, featuring the self-consistent evolution of the liquid/vapor (L/V) interface together with full simulation of fluid flow and heat transfer. Important interfacial phenomena, such as free surface evolution, evaporation, kinetic Knudsen layer, homogeneous boiling, and multiple reflections, are considered and applied to the model. The level set approach is adopted to incorporate the L/V interface boundary conditions in the Navier-Stokes equation and energy equation. Both thermocapillary force and recoil pressure, which are the major driving forces for the melt flow, are incorporated in the formulation. For melting and solidification processes at the solid/liquid (S/L) interface, the mixture continuum model has been employed. The article consists of two parts. This article (Part I) presents the model formulation and discusses the effects of evaporation, free surface evolution, and multiple reflections on a steady molten pool to demonstrate the relevance of these interfacial phenomena. The results of the full keyhole simulation and the experimental verification will be provided in the companion article (Part II).     

Mobility management for VoIP service: Mobile IP vs. SIP

Wireless Internet access has gained significant attention as wireless/mobile communications and networking become widespread. The voice over IP service is likely to play a key role in the convergence of IP-based Internet and mobile cellular networks. We explore different mobility management schemes from the perspective of VoIP services, with a focus on Mobile IP and session initiation protocol. After illustrating the signaling message flows in these two protocols for diverse cases of mobility management, we propose a shadow registration concept to reduce the interdomain handoff (macro-mobility) delay in the VoIP service in mobile environments. We also analytically compute and compare the delay and disruption time for exchanging signaling messages associated with the Mobile IP and SIP-based solutions.     

A new statistical model for site-specific indoor radio propagationprediction based on geometric optics and geometric probability

The ray-tracing (RT) algorithm has been used for accurately predicting the site-specific radio propagation characteristics, in spite of its computational intensity. Statistical models, on the other hand, offers computational simplicity but low accuracy. In this paper, a new model is proposed for predicting the indoor radio propagation to achieve computational simplicity over the RT method and better accuracy than the statistical models. The new model is based on the statistical derivation of the ray-tracing operation, whose results are a number of paths between the transmitter and receiver, each path comprises a number of rays. The pattern and length of the rays in these paths are related to statistical parameters of the site-specific features of indoor environment, such as the floor plan geometry. A key equation is derived to relate the average path power to the site-specific parameters, which are: 1) mean free distance; 2) transmission coefficient; and 3) reflection coefficient. The equation of the average path power is then used to predict the received power in a typical indoor environment. To evaluate the accuracy of the new model in predicting the received power in a typical indoor environment, a comparison with RT results and with measurement data shows an error bound of less than 5 dB