用CAXA电子图板求解冲模压力中心

在模具设计中 ,冲裁模压力中心通常采用解析法或图解法求解。本文提出一种用CAXA绘图软件在设计制图时直接求解的方法 ,快速直接 ,简单方便 ,精度较高。     

Influence of volatile matter and deposited carbon on coke yield from coals

The relations between coke yields and the volatile matter content of 30 individual and 30 blended coals were investigated. Coke yields and deposited carbon related to volatile matter content can be expressed in the following equations: CY (%) = 97.89?0.86 VMch+VMc; and DC (%)= ?2.24+0.16 VMch; where: CY=real coke yield; VMch = volatile matter content of charging coal; VMc=volatile matter content of coke, and in the case of <2%; DC = deposited carbon. The test results show excellent correlation with practice.     

如何提高预焙铝电解槽阳极质量

预焙阳极的质量已严重制约铝电解技术的发展，必须予以足够的重视．国外在提高阳极质量方面的有效措施，可以供国内阳极工厂技术改造及科研攻关借鉴．     

Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.     

硫醇自组装膜的电化学研究进展

综述了在金电极上硫醇自组装膜的电化学表征方法，性质和应用，介绍了自组装膜上的电子传递机理，并进行了简要的展望。     

发酵工厂中空气净化工艺的合理选择

从节能、降低成本、优化工艺的角度，对无菌空气制备过程中，空气预处理流程的选择、空气净化设备、过滤介质以及设备的遴选进行探讨，以实现工艺和工程设计的优化结合。     

Word的高级应用——制作表单

通过实例,详细讲解用Word的窗体工具建立表单,以解决行政部门制作电子文档的空白表格时,让填写的人员方便、快捷地填写内容,又不随意修改(破坏)原有格式和原文。     

Preparation of phenolic resin derived 3-D ordered macroporous carbon

Three-dimensionally ordered long-range macroporous carbon structures were prepared using commercially available phenolic resin by utilizing sacrificial colloidal silica crystalline arrays as templates that were subsequently removed by HF etching after pyrolysis in an argon atmosphere. SEM, TEM, and BET were employed to characterize the morphology and the surface area of the porous carbon structures. The pore size (150–1000 nm) and BET surface area, which reflect pore volume (298.6 m²/g (1.32 cm³/g) ∼ 93.7 m²/g (0.12 cm³/g)), of the macroporous carbon structures produced were approximately proportional to the size (150–1000 nm) of the sacrificial silica sphere templates used (annealing temp. 550°C). The achieved 550 nm porous carbon structures were examined to function as potential catalyst carriers and were successfully impregnated with Ag or Pt-Ru on their inner walls after borohydride reduction at room temperature. In addition, porous carbon patterns were fabricated using the ‘micromolding in capillary’ technique, which has potential applications in the microreaction technology.