Simple approach for the plasma treatment of polymeric membranes and investigation of the aging effect

The modification of the surface characteristics after treatment with plasma in polymeric materials, such as the aging phenomenon, calls the attention of research in the area of nonthermal plasma technology. In this work, a direct treatment with dielectric-barrier discharge plasma was used on the surfaces of ultrafiltration membranes. The measurements of the contact angle with water, attenuated total reflectance accessory, zeta potential, atomic force microscopy and scanning electron microscopy-MEV were performed on the surfaces to verify changes after plasma treatment and to understand the occurrence and timing of the plasma aging effect. In the analysis of the membrane performance, hydraulic permeation and protein retention tests were performed. The results showed an improvement in wettability and hydrophilic properties in the post-treated membranes. The study of reversibility/aging of the post-plasma surface is important for research that deals with the modification of polymeric membranes. Changes in surface morphology, topography and wettability of the membranes were observed up to seven days after treatment, with a tendency to return to the initial characteristics of the membranes.     

Aramid pulp treated with imidazolium ionic liquids as a filler in rigid polyurethane bio-foams

This article reports an aramid pulp (AP) treated with two ionic liquids (IL), namely 1-n-butyl-3-methylimidazolium chloride (C₄.Cl) and 1-carboxymethyl-3-methylimidazolium chloride (HO₂C), and its use as a filler in reinforced rigid polyurethane foams (RPUF). The RPUF were incorporated with the treated AP at three weight fractions (c.a. 0.1, 0.5, and 1.0 wt%) and were produced by the free rising method. The results showed that the studied IL promoted a better interaction between the AP and the RPUF system, which increased the overall reactivity, imparting a higher cell anisotropy. This also yielded a positive effect in mechanical properties and thermal stability of the RPUF. Compared to the neat RPUF, outstanding increases of approximately 50 and 20% were achieved in compressive modulus and strength, respectively. In all, the use of IL promoted increased compatibility between matrix and reinforcement, especially that HO₂C IL.     

Rheological,thermal and morphological properties of polyethylene terephthalate/polyamide 6/rice husk ash composites

This work deals with the rheological, morphological, and thermal properties of composites having poly(ethylene terephthalate) (PET), polyamide-6 (PA6), and their blends as matrices, and rice husk ash (RHA) as a filler. The study determines the effect of composition on the change in viscosity and rate of degradation during processing in a torque rheometer. Our data indicates that thermal stability and degradation during processing depend on matrix composition and filler concentration. SEM micrographs show both partial adhesion of the filler to the matrices and filler pullout. Optical microscopy shows particle agglomeration and that agglomerate size increased with filler content. FTIR investigates the shifting of absorption bands of PET/PA6 composite after the addition of RHA and attributes the selective dispersion of RHA to the formation of hydrogen bonds. Our data supports the idea that filler employed here is an option to develop polymer composites with improved properties.     

Long-term effect of diesel degradation on polyoxymethylene at different temperatures

Diesel is an important fuel, partly because of the longevity and cleanliness of diesel engines. Often, polymers are in direct contact with diesel and understanding compatibility is critical. Polyoxymethylene (POM) is a thermoplastic used to manufacture automotive fuel pump gears and rotors due to its low coefficient of friction and thermal and dimensional stability. In this study, tensile tests were performed on plain and glass fiber reinforced (POM and POMGF) after immersion in diesel at different temperatures (−10°C, 23°C, and 60°C) for 1000, 2000, 3000, 5000, and 10 000 hour. A mathematical model was developed using data from just three tensile stress-strain curves obtained at two different fluid temperatures and three different immersion times. Model and experimental results show good agreement with one another for all conditions tested.     

Thermal dehydrochlorination of pure PVC polymer: Part I—thermal degradation kinetics by thermogravimetric analysis

Thermal degradation of PVC occurs in two stages, with each stage subdivided into two substages. The first refers to the dehydrochlorination, where hydrochloric acid is formed, and giving polyene structures. Hitherto, the degradation mechanism and action of hydrochloric acid as a catalyst during the dehydrochlorination stage are poorly known. Recently, the importance of the tacticity has gained attention for its influence on the dehydrochlorination mechanism. The present work focused on the dehydrochlorination stage, studying the molecular structure by FTIR analysis and the kinetic parameters by TGA analysis in Nitrogen atmosphere, based on three mathematical methods: Friedman, Kissinger, and Flynn-Wall-Ozawa. The sample was a pure homopolymer obtained by suspension polymerization. The dehydrochlorination kinetics follows a first order reaction model and occurs by nucleation and growth. The dehydrochlorination begins with the loss of very labile chlorine atoms present in defective and isotactic molecular segments. The formed HCl acts as a catalyst in the degradation. Following 40% conversion, a drop in Ea is observed. After that, chlorine atoms present in syndiotactic and atactic sequences, are released and, added to the large number of polyene chain sequences, and an increase in Ea is observed up to 60% conversion, where the dehydrochlorination stage is concluded.     

Analysis of surface integrity for minimum quantity lubricant—MQL in grinding

The quality of machined components is currently of high interest, for the market demands mechanical components of increasingly high performance, not only from the standpoint of functionality but also from that of safety. Components produced through operations involving the removal of material display surface irregularities resulting not only from the action of the tool itself, but also from other factors that contribute to their superficial texture. This texture can exert a decisive influence on the application and performance of the machined component. This article analyzes the behavior of the minimum quantity lubricant (MQL) technique and compares it with the conventional cooling method. To this end, an optimized fluid application method was devised using a specially designed nozzle, by the authors, through which a minimum amount of oil is sprayed in a compressed air flow, thus meeting environmental requirements. This paper, therefore, explores and discusses the concept of the MQL in the grinding process. The performance of the MQL technique in the grinding process was evaluated based on an analysis of the surface integrity (roughness, residual stress, microstructure and microhardness). The results presented here are expected to lead to technological and ecological gains in the grinding process using MQL.     

纳米粒子对钢/钢摩擦副摩擦学性能影响的试验研究

选用合成极压蜗杆油、未加油性剂和极压剂的半成品蜗杆油作为基础试验油 ,将超微金刚石粉、纳米铁粒子和纳米铜粒子分别以两种不同质量比分散到半成品蜗杆油中。在 MM-2 0 0型磨损实验机上 ,考察纳米粒子的抗磨减摩性 ,并与传统的油性剂、极压剂进行比较。同时探索应用于钢 /钢副硬齿面的新型抗磨减摩添加剂。试验结果发现 :平均粒径尺寸为 5 nm的超微金刚石粉具有优于传统油性剂、极压剂的抗磨减摩性能 ,可以大大降低钢 /钢副的摩擦 ,减小磨损。但钢 /钢副中不宜使用含有纳米铁粒子的润滑油。     

Ti-6Al-4V钛合金相颗粒粗化动力学及形貌变化

以Ti-6Al-4V钛合金为例，研究了韧性双相合金不同温度保时相颗粒变化情况。结果表明，在α相颗粒粗化的同时，还伴随着α相形貌由“短棒状”向等轴状转变。在800℃和600℃保温时，α相颗粒粗化机制均为Al原子从其他α相颗粒中沿晶界或相界以一维扩散的方式转移到粗化的相颗粒上来。α相颗粒形貌的改变，分为两个阶段，第一阶段为颗粒内部物质的转移为主；第二阶段为其他α相颗粒物质沿晶界或相界扩散到颗粒比较短的方向上以使该颗粒等轴化。对于800℃保温，第一阶段为颗粒内部Al原子以晶格扩散的方式转移；600℃时，颗粒内物质的转移则沿晶界或相界以一维扩散为主。     

Importance of Reservoir Tributaries to Spawning of Migratory Fish in the Upper Paraná River

Regulation of rivers by dams transforms previously lotic reaches above the dam into lentic ones and limits or prevents longitudinal connectivity, which impairs access to suitable habitats for the reproduction of many migratory fish species. Frequently, unregulated tributaries can provide important habitat heterogeneity to a regulated river and may mitigate the influence of impoundments on the mainstem river. We evaluated the importance of tributaries to spawning of migratory fish species over three spawning seasons, by comparing several abiotic conditions and larval fish distributions in four rivers that are tributaries to an impounded reach of the Upper Paraná River, Brazil. Our study confirmed reproduction of at least 8 long‐distance migrators, likely nine, out of a total of 19 occurring in the Upper Paraná River. Total larval densities and percentage species composition differed among tributaries, but the differences were not consistent among spawning seasons and unexpectedly were not strongly related to annual differences in temperature and hydrology. We hypothesize that under present conditions, densities of larvae of migratory species may be better related to efficiency of fish passage facilities than to temperature and hydrology. Our study indicates that adult fish are finding suitable habitat for spawning in tributaries, fish eggs are developing into larvae, and larvae are finding suitable rearing space in lagoons adjacent to the tributaries. Our findings also suggest the need for establishment of protected areas in unregulated and lightly regulated tributaries to preserve essential spawning and nursery habitats. Copyright © 2014 John Wiley & Sons, Ltd.