Analysis of phenmedipham in agricultural products by HPLC

An analytical method was developed for the determination of phenmedipham (PM) in agricultural products using reversed-phase high-performance liquid chromatography with UV detection. A sample was extracted with acetonitrile, and the acetonitrile layer was separated by salting-out. The acetonitrile phase was isolated and evaporated. The extract was dissolved in diethyl ether-hexane (1 : 1), and then cleaned up on a Florisil column. The column was washed with diethyl ether-hexane (1 : 1), and PM was eluted with acetone-hexane (3 : 7), and the eluate was evaporated. The residue was dissolved in acetone-hexane (2 : 8), and the sample solution was cleaned up on SAX/PSA cartridge. The SAX/PSA cartridge was washed with acetone-hexane (2 : 8), and PM was eluted with acetone-hexane (3 : 7). If required, the eluate of the Florisil column was cleaned up with SAX/PSA and ENVI-Carb/ NH2 cartridges. The SAX/PSA cartridge was washed with acetone-hexane (2 : 8), and connected to be ENVI-Carb/NH2 cartridge. The cartridges were washed with acetone-hexane (3 : 7), and then the SAX/PSA cartridge was removed. PM was eluted with acetonitrile-toluene (3 : 1) from the ENVI-Carb/NH2 cartridge. PM in the eluate was separated isocratically on an ODS column (4.6 mm i.d. x 150 mm, 5 microm) using acetonitrile-water (6 : 4) as a mobile phase (flow-rate 1.0 mL/min, temp. 40 degrees C), with monitoring at 235 nm. The calibration curve was linear from 0.005 microg/mL to 10 microg/mL of PM. The recoveries of PM from eight kinds of agricultural products spiked at levels of 0.1 and 0.02 microg/g were 80.8-98.7%. The determination limit was 0.01 microg/g.     

Phenotypic abnormalities observed in aged cloned mice from embryonic stem cells after long-term maintenance

Somatic/embryonic stem cell cloning has made it possible to produce an individual genomically identical to another individual. However, the cloned animals have a variety of abnormalities caused by the aberrant gene modification, with insufficient reprogramming in cloning. We previously reported abnormalities in cloned mice at birth. In this study, we examined what abnormalities could be seen in cloned mice after long-term maintenance. The aged cloned mice showed multiple abnormalities: increase of body weight, some phenotypic abnormalities in the kidneys, testes and thymus, and lower urea nitrogen in their serum biochemical values. The kidneys of all cloned mice were hypertrophied, with a metamorphic or whitish appearance. The multiple lesions, including the enlarged renal pelvis and distension of the renal veins in histology, might be the result of urine accumulation by urinary tract obstruction. The testes of the cloned mice were atrophied, and showed no sperm formation in histology. In contrast, the thymus was rather hypertrophied, and a comparably increased number of lymphocytes were observed in the medulla, consisting mainly of T cells. By conducting a progeny test between the cloned mice, it was confirmed that these abnormalities in the aged cloned mice were not transmitted to their offspring, indicating that the incomplete reprogramming in clones might be in part responsible for the abnormalities detected in aged clones. These results indicate that the postnatal abnormalities observed in aged cloned mice are varied and can be restored through the germ line.     

Detection of six single-nucleotide polymorphisms associated with rheumatoid arthritis by a loop-mediated isothermal amplification method and an electrochemical DNA chip

An electrochemical DNA chip using an electrochemically active intercalator and DNA probe immobilized on a gold electrode has been developed for genetic analysis. In this study, the six polymorphisms associated with rheumatoid arthritis (RA), N-acetyltransferase2 (NAT2) gene polymorphisms T341C, G590A, and G857A, methylenetetrahydrofolate reductase (MTHFR) gene polymorphisms C677T and A1298C, and serum amyloid A1 (SAA1) gene promoter polymorphism C-13T were simultaneously detected by the electrochemical DNA chip and the loop-mediated isothermal amplification (LAMP) method, which is a novel technique for DNA amplification. Human genomic DNAs were extracted from blood, and the targets containing the six polymorphisms were amplified by the LAMP method. A sample containing the six LAMP products was reacted with the electrochemical DNA chip using a DNA detection system that controls hybridization reaction, washing, electrochemical detection, and data analysis automatically. A total of 31 samples were genotyped by this method, and the results were completely consistent with those determined by the polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) analysis or the PCR direct sequence analysis. The time required for this method was only 2 h, and operations were very simple. Therefore, this method is expected to contribute to personalized medicine based on genotype.     

Theoretical analysis of transient recovery voltages when clearing a transformer secondary fault

An analytical formula for the transient recovery voltage and its derivative dv/dt across a circuit breaker has been derived for the case of a transformer secondary fault. A comparison of the calculated results with field test and EMTP simulation results has demonstrated it to have satisfactory accuracy. By applying the formula, the effects of various circuit parameters on the transient recovery voltage and its derivative dv/dt are elucidated. The derivative dv/dt, defined conventionally as the ratio of the crest value and the time to the crest, is found to be about two‐thirds of the maximum value of dv/dt given as a function of time. In addition, a formula for the critical circuit parameters at which dv/dt across a vacuum circuit breaker reaches the critical condition, that is, the circuit breaker fails to interrupt a fault current, is derived. © 2000 Scripta Technica, Electr Eng Jpn, 134(3): 44–52, 2001     

Field test and EMTP simulation of transient voltages when clearing a transformer secondary fault

A field test was carried out to investigate a fault clearing transient due to current interruption of a three‐phase to ground fault at the secondary side of a 3‐MVA, 22/6.6‐kV transformer by a vacuum circuit breaker. EMTP simulations in comparison with the measured results have made it clear that the capacitance C_p of a CR divider to measure voltages reduces dv/dt of transient recovery voltage across the circuit breaker by the ratio of (C_t/(C_t + C_p) where C_t is the transformer stray capacitance. The leakage inductance evaluated from the transformer rating has been found to be noticeably greater than that determined from the measured fault current possibly due to the transformer saturation. Considering the transformer magnetizing conductance and selecting an appropriate interrupted current, EMTP simulation gives a satisfactory result compared with a field test. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 40–48, 2000     

Cooperative behavior of various agents in dynamic environment

The multi-agent model is a model in which agents with limited ability cooperate each other to accomplish a goal. In this paper, we introduce a multi-agent model in which agents are created to imitate real ants. There are two different type of agents, each type of which has a particular task. We designed agents to communicate each other by using pheromone considering noise. On this model, we observed cooperative behavior of agents and evaluated conditions to make an order of behavior in the model.     

Multi agent architecture for dynamic incremental process planning in the flexible manufacturing system

Due to rapid changes of markets and pressures of competitions, industries are adopting their production ways to support diversity of customer’s needs and increase of new product developments. This paper deals with development of an agent-based architecture of dynamic systems for process planning in the manufacturing systems. In consideration of alternative manufacturing processes and machine tools, the process plans and the schedules of the manufacturing resources are generated incrementally and dynamically. A previously proposed negotiation protocol is customized and improved to generate suitable process plans for the target products real-timely and dynamically, based on the alternative manufacturing processes. The alternative manufacturing processes are presented by the process plan networks and the suitable process plans are searched and generated to cope with both the dynamic status and disturbances of the manufacturing systems. We initiatively combine the heuristic search algorithms of the process plan networks with the negotiation protocols, in order to generate suitable process plans.