Styrene–butadiene rubber/cellulose II/clay nanocomposites prepared by cocoagulation—mechanical properties

In this work, nanocomposites of styrene butadiene rubber (SBR), cellulose II, and clay were prepared by cocoagulation of SBR latex, cellulose xanthate, and clay aqueous suspension mixtures. The incorporated amount of cellulose II was 15 phr, and the clay varied from 0 to 7 phr. The influence of cellulose II and clay was investigated by rheometric, mechanical, physicochemical, and morphological properties. From the analysis of transmission electron microscopy (TEM), dispersion in nanometric scale (below 100nm) of the cellulosic and mineral components throughout the elastomeric matrix was observed. XRD analysis suggested that fully exfoliated structure could be obtained by this method when low loading of silicate layers (up to 5 phr) is used. The results from mechanical tests showed that the nanocomposites presented better mechanical properties than SBR gum vulcanizate. Furthermore, 5 phr of clay is enough to achieve the best tensile properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Organocatalytic Enantioselective Decarboxylative Addition of Malonic Acids Half Thioesters to Isatins

The organocatalytic enantioselective decarboxylative addition of malonic acids half thioesters to isatins using a squaramide catalyst afforded the products with high enantioselectivity. These products are key intermediates in the synthesis of 3‐substituted 3‐hydroxy‐2‐oxindole derivatives. The first enantioselective synthesis of (−)‐flustraminol B has been accomplished.     

Fuel and emissions properties of Stirling engine operated with wood powder

From viewpoints of the environment and fuel cost reduction, small-scale biomass combined heat and power (CHP) plants are in demand, especially wood-waste fueled system, which are simple to operate and maintenance-free with high thermal efficiency similar to oil fired units. These are requested by wood and other industries located in mountainous region. To meet these requirements, a Stirling engine CHP system combined with simplified biomass combustion process with pulverized wood powder was developed.In an R&D project started in 2004 considering wood powder properties as a fuel, combustion performance and emissions in combustion flue gas were tested using combustion test apparatus with commercial size units. The wood powder combustion system was modified and optimized during the combustion test results, and the design of the demonstration plant combined with 55 kW_e Stirling engine power unit was considered. The demonstration plant was finally completed in March of 2006, and test operation has been progressed for the future commercial CHP system.In the wood powder combustion test, wood powder of less than 500 μm is mainly used, and a combustion chamber length of 3 m is applied. In these conditions, the air ratio can be reduced to 1.1 without increasing CO emission of less than 10 ppm and combustion efficiency of 99.9%. In the same conditions, NO_x emission is estimated to be less than 120 ppm (6% O₂ basis). Wood powder was confirmed to have excellent properties as a fuel for Stirling engine CHP system. This paper summarizes the wood powder combustion test, and presents the evaluation of the burner design parameters for the biomass Stirling engine system.     

Polymers degradable under environmental conditions through end-modification of poly(α-methylstyrene) derivatives

To induce degradabilities in polymers in response to environmental conditions, the end-modification reactions of poly(α-methylstyrene) derivatives were carried out. When diphenylphosphine chloride was used as a modifier for the living end of para-substituted PMS, the coupling efficiency was ca. 50%. 2-Phenylallyl halide derivatives such as 2-phenylallyl bromide, 2-(4-tolyl)allyl bromide, and α-trifluoromethylstyrene were found to be suitable end-modification agents. For example, ω-2-phenylallyl PMS was prepared with almost quantitative functionality by the reaction of the living PMS with 2-phenylallyl bromide. In a similar way, ω-3,3-difluoro-2-phenylallyl and ω-2-(4-tolyl)allyl PMS derivatives were synthesized. Based on thermogravimetric analysis, onset of the degradation temperature of the end-modified PMS derivatives decreased in the following order: ω-hydrogen- > ω-3,3-difluoro-2-phenylallyl- > ω-2-phenylallyl- > ω-2-(4-tolyl)allyl-PMS. Actually, the onset temperature of ω-2-(4-tolyl)allyl-PMS derivatives was 50°C lower than that of ω-H-PMS derivatives. These results indicate that the active species is produced effectively at the end unsaturated bond, which initiates the depolymerization of the polymer at rather low temperatures. Ionic degradation of these polymers was also investigated using butyllithium as an anionic initiator and methanesulfonic acid as a cationic initiator. Tendencies similar to the thermal degradation were observed. Therefore, it is concluded that a 2-phenylallyl substituent at the end of the PMS chain induces effective degradation through several mechanisms such as radical, anionic and cationic depolymerization reactions.     

Chemical transformation of chiral monolayer-protected gold clusters: observation of ligand size effects on optical and chiroptical responses

Versatile functionalization of metal clusters is a key step in understanding the reactivity of protective monolayers. We here demonstrate that reaction of the outermost amino groups on (S)-/(R)-penicillamine-protected gold clusters with ethyl isocyanate readily modifies the chiral surface structure through carbamoylation. Interestingly, the clusters are electrophoretically separated by the size of the surface ligand, not by the size of the gold core, which is revealed by UV-vis, IR, and energy dispersive X-ray (EDX) spectroscopy as well as SAXS measurements. The ligand size (or length) is extended through additional reactions of the carbamoylated amino groups with isocyanate, while the chemical similarity in ligand structures is realized by their IR spectral similarity. Optical and chiroptical responses of the separated cluster compounds are thus overall similar to each other, but a close inspection reveals that the ligand size has a small but distinct influence on the chiroptical response of the gold clusters.     

N-Alkylation of chitin and some characteristics of the novel derivatives

Summary Introduction of simple alkyl groups at the C-2 nitrogen of chitin and some properties of the resulting N-alkyl-chitins have been examined. Chitosan was fully deacetylated and treated with three kinds of aldehydes, formaldehyde, acetaldehyde, and pentanal. The Schiff bases of chitosan, whose extents of substitution were dependent on the amount of aldehydes, were reduced with sodium cyanoborohydride to N-alkylated chitosans. The N-alkyl-chitosans were then transformed into the corresponding N-alkyl-chitins by acetylation with acetic anhydride followed by transesterification to remove partly formed O-acetyl groups. The resulting N-methyl-, ethyl-, and pentyl-chitins were amorphous and showed improved affinity for organic solvents. Received: 13 December 2001/Revised version: 11 January 2002/Accepted: 17 January 2002     

Kinetically Stable Bicelles with Dilution Tolerance,Size Tunability,and Thermoresponsiveness for Drug Delivery Applications

Mixtures of a phospholipid (1,2‐dipalmitoyl‐sn‐glycero‐3‐phosphatidylcholine, DPPC) and a sodium‐cholate‐derived surfactant (SC‐C₅) at room temperature formed phospholipid bilayer fragments that were edge‐stabilized by SC‐C₅: so‐called “bicelles”. Because the bilayer melting point of DPPC (41 °C) is above room temperature and because SC‐C₅ has an exceptionally low critical micelle concentration (<0.5 mm ), the bicelles are kinetically frozen at room temperature. Consequently, they exist even when the mixture is diluted to a concentration of 0.04 wt %. In addition, the lateral size of the bicelles can be fine‐tuned by altering the molar ratio of DPPC to SC‐C₅. On heating to ≈37 °C, the bicelles transformed into micelles composed of DPPC and SC‐C₅. By taking advantage of the dilution tolerance, size tunability, and thermoresponsiveness, we demonstrated in vitro drug delivery based on use of the bicelles as carriers, which suggests their potential utility in transdermal drug delivery.     

DRYING AND DEWATERING R&D IN JAPAN

Presently, it has become an urgent and important concern worldwide to reduce the volume of waste and rationally use the waste for electric power generation. Sludge is a dominant part in the family of wastes. Drying of sludge, not only for volume reduction but also for further utilization, is becoming an essential and integral process. On the other hand, as the requirement of new materials production, for example, fine particles of micron or sub-micron scale for advanced materials, some new drying technologies and techniques have emerged. The market-pull may be the direct and active impetus to drying research and development (R&D). In this paper, drying technologies for sludges, fine particles, coatings as well as advanced dewatering are discussed to reflect the “hot” points of drying and dewatering R&D in Japan. And some novel dryers are also presented.     

Removal of nitrogen oxides from air by chemicals-impregnated carbons

Fixation of nitrogen oxides (NO_x) in air onto granular activated carbon impregnated with chemicals was attempted to improve removal efficiency of NO_x by activated carbon adsorption. Nitric oxide (NO) and nitrogen dioxide (NO₂), were tried to remove by a flow test. Fixed-bed adsorption breakthrough curves were obtained when some kinds of carbon were used. The amount adsorbed of NO₂ changed with the amount and kinds of metallic salts impregnated. Chemicals-impregnated carbons were prepared from a commercial activated carbon. Among obtained carbons, the one which showed the highest selectivity for NO_x was chosen, and its performance with the change in humidity was determined. Removal mechanism of NO₂ was estimated, and the carbon impregnated with potassium hydroxide was found to be superior to any other carbon tested. The amount of the adsorbed NO and that produced by the reduction of NO₂ were determined from the breakthrough curves.     

Relationship between degree of polymerization and optical and thermal properties of fluorene in polycarbonate polymers

The influences of average degree of polymerization (D_p) and terminal group on thermal and optical properties of high refractive indexed transparent polymers were investigated. In this study, 9,9‐bis[4–(2‐hydroxyethoxy) phenyl] fluorene (BPEF) homo polymer was selected because it has been used as a representative monomer in high refractive index polymers as well as its unique property. BPEF has stable amorphous phase and reacts like a polymer. Its unique reaction allows continuous investigation from monomer to polymer. For hydroxyl‐terminated polymer, the refractive index (n_d) decreased with increasing D_p. On the other hand, for a phenolic‐terminated group, n_d increased with increasing D_p, and both converged to same value in high D_p region. As for glass transition temperatures (T_g), both terminal group series were increased as D_p increased. Though T_g of hydroxyl‐terminated polymer was higher than that of phenolic‐terminated polymer in the low D_p region, both converged to the same value and the inverse number of T_g had linear correlation against the weight percentage of carbonyl groups (CO), which was calculated by D_p. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45042.