Prediction of the energy dissipation rate in ductile crack propagation

In this paper, energy dissipation rate D vs. Δa curves in ductile fracture are predicted using a ‘conversion’ between loads, load‐point displacements and crack lengths predicted by NLEFM and those found in real ELPL propagation. The NLEFM/ELPL link was recently discovered for the DCB testpiece, and we believe it applies to other cracked geometries. The predictions for D agree with experimental results. The model permits a crack tip toughness R(Δa) which rises from J_c and saturates out when (if) steady state propagation is reached after a transient stage in which all tunnelling, crack tip necking and shear lip formation is established. J_R is always greater than the crack tip R(Δa) and continues to rise even after R(Δa) levels off. The analysis is capable of predicting the usual D vs. Δa curves in the literature which have high initial values and fall monotonically to a plateau at large Δa. It also predicts that D curves for CCT testpieces should be higher than those for SENB/CT, as found in practice. The possibility that D curves at some intermediate Δa may dip to a minimum below the levelled‐off value at large Δa is predicted and confirmed by experiment. Recently reported D curves that have smaller initial D than the D‐values after extensive propagation can also be predicted. The testpiece geometry and crack tip R(Δa) conditions required to produce these different‐shaped D vs. Δa curves are established and confirmed by comparison with experiment. The energy dissipation rate D vs. Δa is not a transferable property as it depends on geometry. The material characteristic R(Δa) may be the ‘transferable property’ for scaling problems in ELPL fracture. How it can be deduced from D vs. Δa curves (and by implication, J_R vs. Δa curves) is established.     

中压电动机传统起动方式的危害性

本通过对中压电动机的几种传统起动方式的探讨分析，阐述了使用这些方法对电网和周围其他用电设备产生的不利影响，提出了改进措施。     

真空钙热还原炉渣的综合利用研究

研究了从真空钙热还原炉渣中回收稀土的工艺条件；采用本工艺得到的合格稀土溶液，其回收率达65．41％；副产品氟化钙用作炼硅铁合金的助熔剂，使钙热还原炉渣得到综合利用。     

复合绝缘子耐电腐蚀特点及其电蚀老化区域性的差异

为了了解复合绝缘子外绝缘材质电蚀老化状态和区域性的差异,对Al(OH)3耐电腐蚀机理、外绝缘材质中Al(OH)3颗粒分布状态和环境污湿因素的实际情况进行了研究。Al(OH)3颗粒分解成水蒸气、析出白色粉末状氧化铝,并催化生成二氧化碳,将使外绝缘材质逐渐微观减薄和加大表面的粗糙度,而引起电蚀老化的污湿环境因素,近期不可能得到改善,因此必然引起其电蚀老化出现区域性差异。此外,外绝缘憎水表面污珠场强变化引起的电晕也是促使电蚀老化的重要因素。     

并联机床后置处理器的开发及实验研究

以六自由度6-TPS型并联机床为模型，阐述了机床控制数据的生成原理和流程；以此为基础，规划了后置处理器的功能和整体结构。对若干关键技术进行了研究和探讨，包括基于参数化二进制格式的内部数据传输，基于刀轴矢量的笛卡儿空间粗插补算法，三维和二维刀具半径补偿，刀位文件的预处理以及加工代码的词法和语法检查等。最后介绍了利用本系统进行的切削实验，验证了系统的工程实用性。     

变压器事故原因分析

通过分析一次变压器事故的原因。指出变压器实际运行中存在的问题。并结合自己的工作经验提出科学的改进建议。     

液氮制冷低气压试验箱的仿真设计

在采用液氮制冷的低气压试验箱的设计中,用常规工程设计方法计算的降温过程冷负荷过大,从而导致真空系统设计容量过大。本文采用分布参数模型对试验箱低气压条件下降温过程的冷负荷进行了精确仿真模拟,以此作为真空系统容量设计的基础,减小了设计规模,取得了良好的效果。     

Convergence of simultaneous perturbation stochastic approximation for nondifferentiable optimization

We consider simultaneous perturbation stochastic approximation for function minimization. The standard assumption for convergence is that the function be three times differentiable, although weaker assumptions have been used for special cases. However, all work that we are aware of at least requires differentiability. We relax the differentiability requirement and prove convergence using convex analysis.     

钕电解阳极过电位的测定

用慢扫描示波法测定了钕电解的阳极过电位 .考察了温度、阳极电流密度、Nd2 O3添加量、电解质组成等因素对阳极过电位的影响 ,探讨了降低阳极过电位的可能途径 .结果表明 ,阳极过电位随阳极电流密度的增加而增大 ,随温度的升高而减小 ,一定范围内 ,阳极过电位与阳极电流密度的对数呈线性关系 ,满足塔菲尔方程 ;电解质中LiF和Nd2 O3浓度增加 ,阳极过电位降低 ;适当控制阳极电流密度、升高温度、增加电解质中LiF和Nd2 O3的浓度并尽可能减小极间距 ,均有利于降低阳极过电位     

离心式高炉鼓风机扩压叶片断裂事故分析及处理

通过高炉鼓风机扩压叶片断裂事故，从化学分析、物理检验，结合使用情况对扩压叶片断裂原因进行了详细分析，并提出了改进措施。