Crack deflection analyses of different peel stopper designs for sandwich structures

This paper relates to a newly developed peel stopper concept for sandwich structures. The proposed concept is a specially designed core insert, which has the ability to confine face sheet debonding/delamination (peeling) by deflecting a delamination crack front away from the face/core interface into the bulk of the sandwich core, and thereby constraining the debonding/delamination to a limited prescribed area. In this paper various peel stopper designs are analysed for their ability to deflect cracks away from propagating along a face–core interface. The crack deflection ability of the studied peel stopper designs leads to design guidelines, which describes the minimum requirements regarding the relation between the two interface toughnesses. The analysis further reveals that compliant peel stopper wedges are preferred because they lead to the lowest interface toughness ratio requirement. This has been confirmed through an experiment with a sandwich beam subjected to three-point bending loading. The experiment has shown that the ability of a peel stopper to deflect cracks is highly dependent on the stiffness of the wedge.     

Dynamic rheological measurements on heat-induced myosin gels: An evaluation of the method's suitability for the filamentous gels

Formation of bovine myosin gels (10 mg ml^?1) by heat treatment at pH 6 and an ionic strength of 0.24 M has been monitored by using the Bohlin Rheometer System in the oscillatory mode. Rheological thermograms were determined with a general repeatability of about 2% for a given suspension. A pronounced maximum and an accompanying minimum in storage modulus (G′) were found at about 50 and 55°C, respectively. The thermograms for the loss modulus (G″) and the phase angle (δ) displayed complex behaviour as well, suggesting a multitransition process. Presumably, denaturational events in parts of the molecule are responsible for the complex rheology observed. This complexity is not related to trivial wall slippage as data obtained from cells with different gap sizes were highly reproducible and consistent with other measurements. A decrease in heating rate from 2.5 to 0.1°C min^?1 had a large effect on G′; it increased from 905 to 1600 N m^?2 for gels at 75°C. The phase angle was also affected by the heating rate, especially at about 55°C. The effect of increasing the strain from 0.003 to about 0.1 was significant in two temperature regions; G′ at temperatures higher than 65°C and δ at temperatures lower than 54°C increased with increasing strain.     

Exposure to genotoxins present in ambient air in Bangkok, Thailand--particle associated polycyclic aromatic hydrocarbons and biomarkers

Exposure to genotoxic compounds in ambient air has been studied in Bangkok, Thailand, by analysis of polycyclic aromatic hydrocarbons (PAHs) associated with particles and using different biomarkers of exposure. Eighty-nine male, non-smoking Royal Thai police officers were investigated. The police officers were divided into a high exposure group (traffic police) and low exposure (office duty). Particulate matter was collected using personal pumps (2 l/min) and the eight carcinogenic PAHs were analysed by standard procedures. The traffic police was exposed to a 20-fold higher level of total PAHs than office police (74.25 ng/m3 vs. 3.11; P= 0.001). A two-fold variation was observed between the different police stations. The major PAHs in all groups was benzo[g,h,l]pyrelene. Large inter-individual differences in biomarker levels were observed, but the level of all markers was statistically significantly higher in the traffic police group than in the office group. The level of 1-hydroxypyrene (1-HOP) was 0.181+/-0.078 (range 0.071-0.393) micromol/mol creatinine in the traffic group and 0.173+/-0.151 (P = 0.044) in the office group. The bulky carcinogen DNA-adduct level, determined by P32-post-labelling, was 1.6+/-0.9 (range 0.4-4.3) adducts/10(8) nucleotides in the traffic group and 1.2+/-1.0 (0.2-4.9) in the office group (P = 0.029; Mann-Whitney U-test). The serum PAH-albumin adduct level was 1.76 (0.51-3.07) fmol adducts/microg albumin in the traffic group and 1.35+/-0.77 (0.11-3.45; P = 0.001) in the office group. Lower biomarker levels were observed during the period when the traffic police officers were wearing a simple facemask, indicating that these masks protect against particle-associated PAHs. No statistically significant correlations were observed between biomarker levels and the level of individual PAHs or total PAH. Our data show, that people in Bangkok, who spend most of the day outside air-conditioned offices, are exposed to high levels of genotoxic PAHs. However, for people who spend their working day in offices, the exposure is similar to people living in other metropolitan areas.     

Urban benzene exposure and oxidative DNA damage: influence of genetic polymorphisms in metabolism genes

Benzene has been implicated as an environmental risk factor in leukaemia and other haematological diseases. Relationships between urban benzene exposure, oxidative DNA damage and polymorphisms in metabolism enzymes were examined in 40 volunteers living and working in Copenhagen. Personal exposures to benzene, toluene and methyl tert-butyl ether (MTBE) were monitored during a 5-day period. DNA damage was measured by 7-hydro-8-oxo-2'-deoxyguanosine (8-oxodG) in lymphocyte DNA and urine and by comet assay with use of fapyguanine glycosylase (FPG) and endonuclease III (ENDO). Excretion of the benzene metabolites trans,trans-muconic acid (ttMA) and S-phenylmercapturic acid (S-PMA) were measured in urine. Polymorphisms in glutathione-S-transferases T1 (GSTT1), M1 (GSTM1) and P1 (GSTP1) and NAD(P)H:quinone oxidoreductase (NQO) were determined. Median exposures to benzene, toluene and MTBE were 2.5, 18.7 and 0.86 microg/m(3). No significant correlations between external benzene exposure and any of the biomarkers were found. However, a significant correlation between S-PMA excretion and 8-oxodG in lymphocytes was found (R(s)=0.39). Men were found to excrete significantly more ttMA than the women did and ttMA excretion in men was found to be significantly associated with external benzene exposure (R=0.53, P=0.025). In addition, ttMA and S-PMA excretion was significantly higher in subjects with the NQO+/-genotype compared with subjects with the wild type (P=0.004 and P=0.011, respectively). Even though there are some limitations in this study due to the low range of benzene exposure and biomarker concentrations as well as a small number of subjects, these results could suggest that even at ambient concentrations exposure to benzene could have genotoxic effects in susceptible individuals.     

Dust and the Sick Building Syndrome

Background. In the Danish Town Hall Study" it has previously been shown that the sick building syndrome is a widespread phenomenon. This has given rise to speculations as to whether biologically active components in dust or whether absorbed organic gases and vapours in the indoor climate may be partly responsible for the sick building syndrome. Therefore, we wished to study whether qualitative conditions in dust, of a physical, chemical, and biological nature, are related to the prevalence of symptoms of the sick building syndrome. Material and methods. The study included 12 town halls in the Copenhagen area. A total of 870 persons participated, 584 women and 286 men. All the participants filled out a questionnaire regarding health and working conditions, and dust samples were collected with a special vacuum cleaner in the working environment of the participants, after which the contents of inorganic and organic particles as well as of human source fragments the (hair, nails, skin) and various fibres were determined. Results. There was a significant correlation (P<0.05) between the prevalence of gram-negative bacteria in the indoor climate dust, and general symptoms (fatigue, heavy-headedness, headache, dizziness, concentration problems) (corr.coeff.=0.73), as well as symptoms from the mucous membranes of the upper respiratory tract (corr.coeff.=0.76). Also, there was a significant relation between the prevalence of particles in the dust and the prevalence of symptoms from the mucous membranes (corr.coeff.=0.81). There was a strong and significant correlation between the total amount of volatile organic components (TVOC) and lack of concentration (corr.coeff. =0.85) and feeling heavy-headed (corr.coeff.=0.72). Macromolecular dust (potentially allergenetic material) was significantly correlated to the prevalence of headache and general malaise/dizziness (corr.coeff.=0.66), while the ability of the dust to liberate histamine was significantly related to the prevalence of general malaise, dizziness (corr.coeff.=0.65) and lack of concentration (corr.coeff. =0.58). Further analyses including a number of potential confounders did not change the results of the above analyses. Conclusion. The results of this study support the hypothesis that qualitative properties of dust are important to the sick building syndrome. The study was based on relatively few buildings, but nevertheless strong correlations were found. In perspective, epidemiological intervention studies should be carried out to investigate whether minimizing the amount of both dust and bacteria in the indoor climate affect the prevalence of sick building syndrome.     

Design and development of guide vane cascade for a low speed number Francis turbine

Guide vane cascade of a low speed number Francis turbine is developed for the experimental investigations.The test setup is able to produce similar velocity distributions at the runner inlet as that of a reference prototype turbine.Standard analytical methods are used to design the reference turbine.Periodic walls of flow channel between guide vanes are identified as the starting profile for the boundary of the cascade.Two alternative designs with three guide vanes and two guide vanes,without runner,are studied.A new approach,for the hydraulic design and optimization of the cascade test setup layout,is proposed and investigated in details.CFD based optimization methods are used to define the final layout of the test setup.The optimum design is developed as a test setup and experimental validation is done with PIV methods.The optimized design of cascade with one guide vane between two flow channels is found to produce similar flow conditions to that in the runner inlet of a low speed number Francis turbine.     

All solution processed tandem polymer solar cells based on thermocleavable materials

Multilayer tandem polymer solar cells were prepared by solution processing using thermocleavable polymer materials that allow for conversion to an insoluble state through a short thermal treatment. The problems associated with solubility during application of subsequent layers in the stack were efficiently solved. Devices comprised a transparent front cathode based on solution processed zinc oxide nanoparticles, a large band gap active layer based on a bulk heterojunction between zinc oxide and poly(3-carboxydithiophene) (P3CT) followed by a layer of PEDOT:PSS processed from water. The second cell in the stack employed a zinc oxide front cathode processed on top of the PEDOT:PSS layer from an organic solvent, a low band gap active layer based on a bulk heterojunction between zinc oxide and the novel poly(carboxyterthiophene-co-diphenylthienopyrazine) (P3CTTP) followed by a layer of PEDOT:PSS again processed from water and finally a printed silver electrode. The devices were prepared without the use of fullerenes and vacuum steps and employ only thermal treatments and orthogonal solvents. The devices exhibited operational stability in air without any form of encapsulation.     

Kranbahnträger aus warmgewalzten Mannesmann‐Stahlhohlprofilen (MSH)

Crane runway made of hot‐rolled Mannesmann steel hollow sections (MSH). A new crane runway over a couryard on the production site of Vallourec & Mannesmann Deutschland GmbH in Düsseldorf, Germany should be realised using quadratic hot‐rolled hollow sections. For this purpose a new design was to be developed and realised. Until now crane runways for large spans and high loads have been built using box girders or individual designed special solutions. The production of these girders as well as the erection on site is complex and expensively in terms of time and costs. On the basis of a close collaboration of all involved project partners and under the leadership of Dittmann & Pollmann, Hagen, Germany the technical challenge was mastered and a new type of crane runway was realised.     

Mechanical characterization and fractography of glass fiber/polyamide (PA6) composites

The mechanical properties of the glass fiber reinforced Polyamide (PA6) composites made by prepreg tapes and commingled yarns were studied by in‐plane compression, short‐beam shear, and flexural tests. The composites were fabricated with different fiber volume contents (prepregs—47%, 55%, 60%, and commingled—48%, 48%, 49%, respectively) by using vacuum consolidation technique. To evaluate laminate quality in terms of fiber wet‐out at filament level, homogeneity of fiber/matrix distribution, and matrix/fiber bonding standard microscopic methods like optical microscopy and scanning electron microscopy (SEM) were used. Both commingled and prepreg glass fiber/PA6 composites (with V_f ∼ 48%) give mechanical properties such as compression strength (530–570 MPa), inter‐laminar shear strength (70–80 MPa), and transverse strength (80–90 MPa). By increasing small percentage in the fiber content show significant rise in compression strength, slight decrease in the ILSS and transverse strengths, whereas semipreg give very poor properties with the slight increase in fiber content. Overall comparison of mechanical properties indicates commingled glass fiber/PA6 composite shows much better performance compared with prepregs due to uniform distribution of fiber and matrix, better melt‐impregnation while processing, perfect alignment of glass fibers in the composite. This study proves again that the presence of voids and poor interface bonding between matrix/fiber leads to decrease in the mechanical properties. Fractographic characterization of post‐failure surfaces reveals information about the cause and sequence of failure. POLYM. COMPOS., 36:834–853, 2015. © 2014 Society of Plastics Engineers