Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Properties of aqueous solutions for two binary mixed systems between two kinds of bile salts and nonionic surfactants

The micellar properties of aqueous binary mixed solutions for two systems consisting of sodium cholate (NaC)-octaoxyethylene glycol mono n-decyl ether (C₁₀E₈) and sodium glycocholate (NaGC)-C₁₀E₈ have been studied on the basis of surface tensions, polarity of the micelle interior and the mean aggregation number. Application of two theoretical treatments, based on regular solution and excess thermodynamic quantities for critical micellar concentration (CMC) data from surface tension curves of two mixed systems showed that the mole fraction of each bile salt in the mixed micelles near the CMC is lower than that of the corresponding prepared mole fraction in the mixed solution. The polarity of the interior suggested that the hydrophobicity of intramicelles increased with the increase of the mole fraction of bile salt in the mixed solution and that the mixed micelles become dramatically more hydrophobic at a mole fraction of 0.68 for NaGC−C₁₀E₈ system and 0.75 for NaC−C₁₀E₈ system, respectively. This implies that the micelles become richer in the bile salt molecules and the tendency appears strongly for NaGC−C₁₀E₈ system due to the strong cohesion between the conjugated glycines in the NaGC molecules. The decrease of aggregation number with the increase of the mole fraction of bile salts shows that the micelles approach those of the single system of each bile salt. This supports the previously mentioned facts.     

Thraustochytrid as a potential source of carotenoids

Thraustochytrids, marine protists whose dominant genera are Thraustochytrium and Schizochytrium, belong to the kingdom Chromista and are known as an industrial source of DHA. We describe here that thraustochytrid strain KH105, isolated as a DHA producer, also accumulates significant levels of β-carotene and xanthophylls including canthaxanthin and astaxanthin. A4-d cultivation using a medium composed of 10% glucose and less than 0.3% of nitrogen sources in a half-concentration of seawater gave an astaxanthin production up to 6.1 mg/L, and canthaxanthin content reached more than 10 mg/L under conditions where a higher concentration of nitrogen sources (6%) was employed. It might be advantageous in mass production systems for these carotenoids to be extracted readily by simply suspending the cells with organic solvents such as acetone and chloroform. Analyses on the morphological and life history features of the KH105 strain revealed that it belongs to the genus Schizochytrium. This particular species of thraustochytrids is thus considered to be a promising source of xanthophylls as well as DHA for use in the food industry.     

Elastoplastic Finite Element Analysis and Strength Evaluation of Adhesive Butt Joints of Similar and Dissimilar Hollow Shafts Subjected to External Bending Moments

Stress distributions and deformation of adhesive butt joints are analyzed by an elastoplastic finite element method when the joints of similar and dissimilar shafts are subjected to external bending moments. The effects of the ratio of Young's modulus for the adherends to that for an adhesive and the effects of the adhesive thickness on the interface stress distribution are investigated. Joint strength is predicted by using the elastoplastic interface stress distributions. It is found that the singular stress at the edge of the interfaces increases with an increase of the ratio of Young's modulus. Measurement of strains in joints and experiments on joint strength were conducted. The numerical results are in fairly good agreement with the experimental results. It is observed that the joint strength for dissimilar shafts are smaller than those for similar shafts. A fracture of dissimilar adhesive up-bonded shafts occurred from the interface of the adherend with smaller Young's modulus. It is seen that joint strength increases as the adhesive thickness increases.     

Reaction products of α-tocopherol with methyl linoleate-peroxyl radicals

α-Tocopherol was reacted with methyl linoleateperoxyl radicals at 37°C. The peroxyl radicals were generated by the reaction of methyl linoleate with a free radical initiator, 2,2′-azobis(2,4-dimethylvaleronitrile). The primary products of α-tocopherol with methyl linoleate-peroxyl radicals were isolated by reversephase and normal-phase high performance liquid chromatography (HPLC), and their structures were characterized by ultraviolet (UV), infrared (IR),¹H and¹³C nuclear magnetic resonance (NMR) and mass spectrometry (MS). There were four stereoisomers of methyl 13-(8a-peroxy-α-tocopherone)-9(Z),11(E)-octadecadienoate and four stereoisomers of methyl9-(8a-peroxy-α-tocopherone)-10(E),12(Z)-octadecadienoate.     

Temperature measurements of polymer melts in the heating barrel during injection molding. Part I. Temperature distribution along the screw axis in the reservoir

A new procedure has been developed to measure the temperature distribution of the polymer melts along the screw axis during injection by using a small sheath thermocouple. At the same time, the effects of molding conditions on temperature distribution has been studied. The temperature distribution of the polymer melt along the screw axis during injection can be obtained from the difference between the standard temperature profile and the temperature profile of the polymer melt with unknown and non-uniform temperature measured under the same rate of injection. The temperature of a polymer melt within a shot is not uniform. The difference between the maximum and the minimum temperature within a shot may exceed 10°C in some cases. There are two major factors which govern the effects of molding conditions on the temperature distribution of the polymer melts during injection. The first is the amount of shear heating in the metering zone. The second is the amount of heat absorbed into the polymer in the compression and feed zones.     

Liquid crystalline side-chain polysiloxanes containing mesogenic groups attached by esterification

Summary Liquid crystalline side-chain polysiloxanes were prepared without metal complex catalyst. Mesogenic groups such as cholesteryl, 4-cyano-4-biphenyl and 4-methoxy-4-biphenyl group were introduced into polysiloxane by esterification and from DSC measurements they were compatible with other liquid crystalline polysiloxanes reported previously.     

Nonlinear effects on spin waves in3He-4He dilute solutions

Spin dynamics of³He-⁴He dilute solution have been studied in the collisionless regime by NMR methods. In cw NMR experiments, we observed spin waves in a magnetic field gradient. The frequency difference between the first mode and the others obeyed a two-thirds power law in the strength of the field gradient. By using a pulsed NMR method, nonlinear spin dynamics were studied. We observed the large amplitude spin waves after an rf pulse. The frequency of each spin-wave mode depended on the tipping angle. By using the parameter determined in the present experiment, the numerical calculated results based on Leggett-Rice theory are in good agreement with the results of the pulsed NMR experiments.     

Formation and transformation of cubic 3PbO·2Ta2O5 solid solution

The formation of lead tantalates in the PbO-rich region is studied using the powders prepared by the simultaneous hydrolysis of lead and tantalum alkoxides. Cubic 3PbO · 2Ta₂O₅ solid solutions crystallize at low temperatures from amorphous materials between 60 and 75 mol% PbO. The lattice parameter,a, increases linearly from 1.0545 to 1.0705 nm with increasing PbO. At higher temperatures the solid solutions above 66.67 mol% PbO are transformed into those of rhombohedral 2PbO · Ta₂O₅. Rhombohedral 5PbO · 2Ta₂O₅ is formed at 850 to 900 °C by transformation of 2PbO·Ta₂O₅ solid solution corresponding to 71.43 mol% PbO. The existence of previously reported 3PbO·Ta₂O₅ is not confirmed.     

Phase evolution and <110>-orientation mechanism in RTGG-processed BaTiO3 ceramics with electrical properties

The <110>-oriented BaTiO₃ ceramics were fabricated using BaCO₃ matrix and H_1.08Ti_1.73O₄.nH₂O (HTO) template particles, and the mechanism of BaTiO₃ phase formation was investigated. The dielectric, ferroelectric, and piezoelectric properties were also investigated. The transformation of the HTO phase into the TiO₂ bronze or TiO₂ (B) phase was observed at 600°C, where the BaTiO₃ nucleation was accompanied by the formation of a Ba₂TiO₄ phase. The TiO₂ phase reacted with the Ba₂TiO₄ phase at 800°C to give a BaTiO₃ phase, whereas its reaction with the BaTiO₃ resulted in the formation of BaTi₂O₅ phase that got decomposed into BaTiO₃ and Ba₆Ti₁₇O₄₀ phase at sintering temperature ≥1300°C. Sintering with samples’ embedding in BaTiO₃ powders prevented the formation of the Ba₆Ti₁₇O₄₀ secondary phase. The crystallographic orientation along the <110> direction (F₁₁₀) was developed by the epitaxial grain growth mechanism. In addition to the contribution of the grain-size increment for enhancing the F₁₁₀, the preservation of the platelike structure was also found to have a significant impact. The ceramics prepared by the embedded sintering (grain size ≈12.4 µm and F₁₁₀ = 83%) exhibited the room-temperature dielectric constant of 1708 and piezoelectric strain constant of 445 pm/V, which are higher than those of the BaTiO₃ ceramics with randomly oriented grains.