Reappraisal of loading rate effects on sand behavior in view of seismic design for pile foundation

This study re-visits the effects of loading rate on sand behavior in view of seismic design of pile foundation. Based on an extensive literature review covering both element testing and model testing, the paper summarizes the current understanding of the loading rate effects. The paper then describes the development of test apparatus used in this study and presents the data obtained from a series of monotonically increasing triaxial compression tests on Toyoura sand, varying the strain rate in the range of 0.005%/s to 250%/s. A total of 36 tests were conducted on dry and saturated sand, both under drained and undrained conditions with two confining pressures. The experimental results confirm that the soil strength and the soil stiffness increase as the strain rate increase. This paper also concludes that the internal friction angle and deformation modulus increase when the strain rate is high. The implications of the loading rate effect on pile foundation design are then presented.     

Laser brazing of a dissimilar joint of austenitic stainless steel and pure copper

In many industries, there are applications that require the joining of stainless steel and copper components; therefore, the welding of dissimilar stainless steel/copper joints is a common process. For this investigation, the optimal brazing conditions and suitable filler metals for laser brazing of stainless steel/copper lap joints were studied. Tensile shear force increases with increases in the laser spot diameter or in the laser irradiation angle, which is associated with increased bonding width; however, as bonding width approaches 2 mm, tensile shear force reaches a saturated value due to fracturing at the HAZ of the Cu base plate. In order to obtain joints with high tensile shear strength, laser brazing was optimized by using Cu–Si-based filler metal under the following conditions: laser power, 4 kW; spot diameter, 3 mm; laser irradiation angle, 80°; irradiation position shift, 0.6 mm; brazing speed, 0.30 m/min; and filler metal feed speed, 0.30 min. Concerning filler metals, it was found that the Ni–Cu type showed relatively large tensile shear force even at high welding speeds in comparison with those of the Cu–Si, Cu, Cu–Ni, Ni–Cu and Ni types, respectively.     

Nanostructured poly(3-hexylthiophene-2,5-diyl) films with tunable dimensions through self-assembly with polystyrene

Poly(3-hexylthiophene-2,5-diyl) is among the most widely used conjugated polymers for opto-electronic applications. To enhance its properties, researchers have attempted to nanostructure this polymer using various processes including breath figure arrays, nanolithography and elaborated organic synthesis. We here demonstrate a simple process to nanostructure the conjugated polymer using self-assembly with polystyrene and selective removal of one of the phases. The influence of the molecular weight of each polymer on the thin film morphology was systematically studied by atomic force microscopy. Using this approach, we observe two types of nanostructure, namely, nanoporous and nanoisland structures, of which the dimensions can be tuned by modifying the molecular weight of each polymer in the blend. This simple process introduces a cost-effective alternative to produce thin films of conjugated polymer with average nano-features from 100 nm up to 500 nm which could be used in a wide range of applications.     

Fabrication of porous magnesium spinel with directional pores by unidirectional solidification

A porous magnesium spinel (MgAl₂O₄) with directional pores was fabricated by unidirectional solidification in pressurized argon and hydrogen mixed gases. Two different kinds of pores with large directional and small facet shape were formed in the solidified samples. The former pores were dominant in the porous structure. A small amount of free corundum phase was formed in the solidified porous spinel as a secondary phase by vaporization of MgO component during the solidification process. With increasing total gas pressure, the pore size of the solidified samples decreased while no change in the porosity. The porosity and pore size of the samples increased with increasing hydrogen partial pressure. The porosities of the samples fabricated under 10%H₂–90%Ar and 1%H₂–99%Ar mixed gases were 30 and 10%, respectively, and that under Ar atmosphere was very low, non-porous.     

Supercritical fluid extraction of fungal oil using CO2, N2O,CHF3 and SF6

The extraction of oil from fungi (Mortierella ramanniana var.angulispora) was studied using carbon dioxide (CO₂), nitrous oxide (N₂O), trifluoromethane (CHF₃) and sulfur hexafluoride (SF₆) under supercritical conditions. The oil solubility was highest in SC-N₂O followed by SC-CO₂, while both SC-CHF₃ and SC-SF₆ showed poorer solvent power. The recorded oil solubilities at 333 K and 24.5 MPa were 2.3 wt% in N₂O, 0.48 wt% in CO₂, 0.0099 wt% in CHF₃ and 0.0012 wt% in SF₆. The oil solubilities in SC-N₂O and SC-CO₂ were measured over the pressure range 15.7–29.4 MPa and at temperatures ranging from 313–353 K. N₂O always showed greater solvent power than did CO₂ at the same temperature and pressure. The solvent power of a supercritical fluid increases with density at a given temperature, and increases with temperature at constant density. The change in neutral lipid composition of the extracted oil with the extraction ratio was measured. Free fatty acids or diglycerides were extracted more easily than triglycerides or sterol esters. The change in fatty acid composition was also measured. The proportion of γ-linolenic acid in the extract remained constant throughout the extraction.     

基于图像相关分析的砂土模型试验变形场量测

高分辨率数码相机的出现为砂土模型试验变形场非接触量测法的研究开发提供了一条简便经济而且实用的途径,在模型试验观测面上,不再需要布置嵌入式量测标志点或描画网格,直接用数码相机在试验各阶段拍摄照片,然后对照片序列进行图像相关分析,即可得出模型试验的变形场分布。利用图像匹配技术追踪模型上点的位移,借用FEM常用的等参单元的概念进行图像校准和应变计算,采用双线性插值技术可以实现微小变形量测,并提出同时用平移和旋转搜索方法,以适应砂土模型的变形特点。精度检验试验结果表明,一个像素以下的平移量测标准方差达到0.19个像素,数值试验表明,15°旋转刚体变形量测,非旋转搜索和旋转搜索的标准方差分别为0.49和0.08个像素。最后给出一个在砂土地基承载力离心机模型试验中的应用实例,分析结果包含砂土模型位移场、最大剪应变场和体积应变场的分布图。结果表明这一方法使得砂土模型局部化变形、剪切带和渐进破坏过程的量化分析成为可能。     

Microwave holographic imaging method with improved resolution

A multifrequency holographic microwave imaging method with high resolving capability in both azimuth and range directions, is described. The method incorporates a synthetic aperture approach in pulse radar systems, originally designed for the pulse-echo imaging, in order to improve azimuth resolution. The imaging technique places no constraint on the waveform of a transmitted signal in use and allows the three-dimensional imaging. This paper develops 1) the general formula, which describes the relation between the transmitted and received signals, based on Kirchhoff diffraction theory, 2) a test function, which is the kernel of a linear operation for producing object images from received signals, and 3) a filter design technique for compressing the durations and suppressing the sidelobe levels of received signals. Numerical image reconstructions are presented for demonstrating high resolution capability of the method.     

The Ameliorative Effect of Dexamethasone on the Development of Autoimmune Lung Injury and Mediastinal Fat-Associated Lymphoid Clusters in an Autoimmune Disease Mouse Model

In our previous study, we revealed the ameliorative therapeutic effect of dexamethasone (Dex) for Lupus nephritis lesions in the MRL/MpJ-Fas ^lpr/lpr (Lpr) mouse model. The female Lpr mice developed a greater number of mediastinal fat-associated lymphoid clusters (MFALCs) and inflammatory lung lesions compared to the male mice. However, the effect of Dex, an immunosuppressive drug, on both lung lesions and the development of MFALCs in Lpr mice has not been identified yet. Therefore, in this study, we compared the development of lung lesions and MFALCs in female Lpr mice that received either saline (saline group “SG”) or dexamethasone (dexamethasone group “DG”) in drinking water as a daily dose along with weekly intraperitoneal injections for 10 weeks. Compared to the SG group, the DG group showed a significant reduction in the levels of serum anti-dsDNA antibodies, the size of MFALCs, the degree of lung injury, the area of high endothelial venules (HEVs), and the number of proliferating and immune cells in both MFALCs and the lungs. A significant positive correlation was observed between the size of MFALCs and the cellular aggregation in the lungs of Lpr mice. Therefore, this study confirmed the ameliorative effect of Dex on the development of lung injury and MFALCs via their regressive effect on both immune cells’ proliferative activity and the development of HEVs. Furthermore, the reprogramming of MFALCs by targeting immune cells and HEVs may provide a therapeutic strategy for autoimmune-disease-associated lung injury.