The inverse design of the wind turbine blade sections by the singularities method

The aerodynamic characteristics of wind turbines are closely related to the geometry of their blades. The innovation and the technological development of wind turbine blades can be centred on two tendencies. The first is to improve the shape of existing blades; the second is to design new shapes of blades. The aspiration in the two cases is to achieve an optimal circulation and hence enhancing some more ambitious aerodynamic characteristics. This paper presents an inverse design procedure, which can be adapted to both thin and thick wind turbine blade sections aiming to optimise the geometry for a prescribed distribution of bound vortices. A method for simulating the initial contour of the blade section is exposed, which simultaneously satisfy the aerodynamic and geometrical constraints under nominal conditions. A detailed definition of the function characterising the bound vortex distribution is presented. The inviscid velocity field and potential function distributions are obtained by the singularities method. In the design method implemented, these distributions and the circulation of bound vortices on the camber line of the blade profile, are used to rectify its camber in an iterative calculation leading to the final and optimal form of the blade section once convergence is attained. The scheme proposed has been used to design the entire blade of the wind turbine for a given span-wise distribution of bound circulation around the blade contour.     

Engineering economic analysis of biomass IGCC with carbon capture and storage

Integration of biomass energy technologies with carbon capture and sequestration could yield useful energy products and negative net atmospheric carbon emissions. We survey the methods of integrating biomass technologies with carbon dioxide capture, and model an IGCC electric power system in detail. Our engineering process model, based on analysis and operational results of the Battelle/Future Energy Resources Corporation gasifier technology, integrates gasification, syngas conditioning, and carbon capture with a combined cycle gas turbine to generate electricity with negative net carbon emissions. Our baseline system has a net generation of 123 MW_e, 28% thermal efficiency, 44% carbon capture efficiency, and specific capital cost of 1,730 $ kW_e⁻¹. Economic analysis suggests this technology could be roughly cost competitive with more conventional methods of achieving deep reductions in CO₂ emissions from electric power. The potential to generate negative emissions could provide cost-effective emissions offsets for sources where direct mitigation is expected to be difficult, and will be increasingly important as mitigation targets become more stringent.     

Optimizing the solar photo-Fenton process in the treatment of contaminated water. Determination of intrinsic kinetic constants for scale-up

The elimination of aromatic compounds present in surface water by photo-Fenton with sunlight as the source of radiation was studied. The concentrations of Fe³⁺ and H₂O₂ are key factors for this process. A solar simulator and a prototype parabolic collector were used as laboratory-scale reactors to find the parameters of those key factors to be used in the CPC (compound parabolic collector) pilot plant reactor. The initial mineralization rate constant (k_obs) was determined and evaluated at different Fe³⁺ and H₂O₂ concentrations to find the best values for maximum efficiency. In all the experiments the mineralization of an aqueous phenol solution was described by assuming a pseudo-first-order reaction. The intrinsic kinetic constants not dependent on the lighting conditions were also estimated for scale-up.     

An evaluation of enhanced oil recovery strategies for a heavy oil reservoir after cold production with sand

Cold heavy oil production with sand (CHOPS) is the process of choice for unconsolidated heavy oil reservoirs with relatively high gas content. The key challenge of CHOPS is that the recovery factor tends to be between 5% and 15%, implying that the majority of the oil remains in the ground after the process is rendered uneconomic. Continued cold production (without sands) is not productive for a post‐CHOPS reservoir because of the low oil saturation and depleted reservoir pressure in the wormhole regions. There is a need to develop viable recovery processes for post‐CHOPS reservoirs. Here, different follow‐up processes are examined for a post‐CHOPS heavy oil reservoir. In post‐CHOPS cold water flooding, severe water channeling is ineffective at displacing high viscosity heavy oil. Hot water flooding improves the sweep efficiency and produces more oil compared with cold water flooding. However, the swept region is limited to the domain between the neighboring wormhole networks, and the energy efficiency of the process is relatively poor. Compared with the hot water flooding case, steam flooding achieves higher oil production rates and lower water use. A cyclic steam stimulation strategy achieves the best performance regarding oil production rates and water usage. Based on our results, it is observed that thermally based techniques alone are not capable to recover the oil economically for post‐CHOPS reservoirs. However, it is suggested that techniques with combined use of thermal energy and solvent could potentially yield efficient oil recovery methods for these reservoirs. Copyright © 2015 John Wiley & Sons, Ltd.     

Stability of wood fast pyrolysis oil

This study evaluates the effects of storage conditions on physical and chemical properties of biomass fast pyrolysis oils exposed to elevated temperatures over extended periods of time. It was performed on oak pyrolysis oil generated in the NREL vortex reactor. Oil samples were stored at three temperatures: 37, 60 and 90°C in glass vessels. Properties of the oils were measured after hours of storage at 90°C, and after days or weeks at lower temperatures. Chemical changes in the oils were measured using GPC (molecular weight distribution) and FTIR spectroscopy. The oil remained a single phase throughout the studied conditions. Its pH was not affected by storage. The water content, viscosity and molecular weight of the oil increased with the time and temperature of storage. First-order reaction kinetics were successfully used to predict changes in molecular weight of the stored oil. FTIR provided evidence that etherification or esterification are mechanisms for condensation of the oil during storage.     

Energy Aware Signal Processing for Software Defined Radio Baseband Implementation

The fast pacing diversity and evolution of wireless communications require a wide variety of baseband implementations within a short time-to-market. Besides, the exponentially increased design complexity and design cost of deep sub-micron silicon highly desire the designs to be reused as much as possible. This yields an increasing demand for reconfigurable/ programmable baseband solutions. Implementing all baseband functionalities on programmable architectures, as foreseen in the tier-2 SDR, will become necessary in the future. However, the energy efficiency of SDR baseband platforms is a major concern. This brings a challenging gap that is continuously broadened by the exploding baseband complexity. We advocate a system level approach to bridge the gap. Specifically, we fully leverage the advantages (programmability) of SDR platforms to compensate its disadvantages (energy efficiency). Highly flexible and dynamic baseband signal processing algorithms are designed and implemented to exploit the abundant dynamics in the environment and the user requirement. Instead of always performing the best effort, the baseband can dynamically and autonomously adjust its work load to optimize the average energy consumption. In this paper, we will introduce such baseband signal processing techniques optimized for SDR implementations. The methodology and design steps will be presented together with 3 representative case studies in HSDPA, WiMAX and 3GPP LTE.     

Effect of substrate flexibility on solder joint reliability

Solder joint fatigue failure is a serious reliability concern in area array technologies, such as flip chip and ball grid array packages of integrated-circuit chips. The selection of different substrate materials could affect solder joint thermal fatigue lifetime significantly. The reliability of solder joint in flip chip assembly for both rigid and compliant substrates was evaluated by accelerated temperature cycling test. Experimental results strongly showed that the thermal fatigue lifetime of solder joints in flip chip on flex assembly was much improved over that in flip chip on rigid substrate assembly. Debonding area of solder joints in flip chip on rigid board and flip chip on flex assemblies were investigated, and it was found that flex substrate could slow down solder joint crack propagation rate. The mechanism of substrate flexibility on improving solder joint thermal fatigue was investigated by thermal mechanical analysis (TMA) technique. TMA results showed that flex substrate buckles or bends during temperature cycling and this phenomenon was discussed from the point of view of mechanics of the flip chip assembly during temperature cycling process. It was indicated that the thermal strain and stress in solder joints could be reduced by flex buckling or bending and flex substrates could dissipate energy that otherwise would be absorbed by solder joints. It was concluded that substrate flexibility has a great effect on solder joint reliability and the reliability improvement was attributed to flex buckling or bending during temperature cycling.     

Delay Fault Testing: Choosing Between Random SIC and Random MIC Test Sequences

The combination of higher quality requirements and sensitivity of high performance circuits to delay defects has led to an increasing emphasis on delay testing of VLSI circuits. In this context, it has been proven that Single Input Change (SIC) test sequences are more effective than classical Multiple Input Change (MIC) test sequences when a high robust delay fault coverage is targeted. In this paper, we show that random SIC (RSIC) test sequences achieve a higher fault coverage than random MIC (RMIC) test sequences when both robust and non-robust tests are under consideration. Experimental results given in this paper are based on a software generation of RSIC test sequences that can be easily generated in this case. For a built-in self-test (BIST) purpose, hardware generated RSIC sequences have to be used. This kind of generation will be shortly discussed at the end of the paper.     

On-Line Error Detection for Bit-Serial Multipliers in GF(2m)

In this paper error detection is applied to four finite field bit-serial multipliers. It is shown that by using parity prediction, on-line error detection can be incorporated into these multipliers with very low hardware overheads. These hardware overheads are generally independent of m and comprise only a handful of gates, so for large values of m these overheads are particularly low. The fault coverage of the presented structures has been investigated by simulation experiment and shown to range between 90% and 94.3%.