Influence of solvent composition and degree of reaction on the formation of surface microtopography in a thermoset siloxane-urethane system

The effects of solvent composition and degree of reaction prior to film formation leading to the formation of a biphasic microtopographical surface in a crosslinked siloxane-urethane coating system were explored. For the solvent composition study, a D-optimal mixture design study was carried out using methyl n-amyl ketone (MAK), toluene, ethyl 3-ethoxypropionate (EEP), butyl acetate (BA) and isopropyl alcohol (IPA) as solvents. The study revealed that the presence of slow evaporating solvents MAK, EEP and the absence of fast evaporating solvent IPA in the solvent composition with a minimal amount of BA favored formation of a structured surface. Control over the domain size could be obtained by varying the MAK:EEP ratio in solvent compositions having a fixed amount of BA. The effect of mixing time on the formation of surface domains was studied. At short mixing times (<2 h) and long mixing times (>7 h), no surface phase separation is observed, while at intermediate times a ‘window’ was found where surface microdomains of similar size are generated. Doubling the level of catalyst halves the mixing time required to generate surfaces with microdomains. Scanning electron microscopy (SEM) studies with energy dispersive X-ray mapping and dynamic mechanical analysis (DMA) were done in order to understand the development of the phases in the PDMS-polyurethane system.     

Structural and photoluminescence studies of Eu3+ doped zinc oxide nanorods prepared by precipitation method

Trivalent europium doped zinc oxide (ZnO:Eu3+) nanocrystals were synthesized via room temperature chemical co-precipitation and they were systematically characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and photoluminescence (PL) spectroscopy. The as-synthesized samples were found to have hexagonal wurtzite coexisted with the intermediate Zn5(OH)8Cl2·H2O phase, while the single hexagonal phase was facilitated due to the calcinations. The as obtained samples were broadly composed of nanoflakes while the highly crystalline nanorods were formed due to low temperature annealing of the as-synthesized samples. The crystallite size of the nanoflakes and nanorods (40-90 nm) were extracted from the XRD pattern which was found to be consistent with scanning electron microscopy (SEM) measurements. The photolumi-nescence (PL) spectra of nanophosphors showed bright red and orange emissions at 618 and 594 nm respectively with efficient broad blue green emission spectrum due to ZnO lattice. Further, a good energy transfer process from ZnO host to Eu3+ was observed in PL emission and excitation spectra of Eu3+ doped ZnO ions. In all, the present nanophosphors were found to have great potentiality for bio-applications.     

Polysaccharides from Sesamum indicum meal: Isolation and structural features

Defatted Sesamum indicum seed cake was extracted, following two separate sequences, and the effects of extraction medium on yield and composition of the extracts were compared. Polysaccharides extracted sequentially with dilute acid and alkali represented 250 mg/g of defatted meal. The isolated polymers contained arabinan, rhamnogalacturonan I (RG I) and arabinogalactan proteins. Polysaccharides extracted during chlorite treatment and with dilute alkali had a higher proportion of rhamnose, suggesting a more branched variety of polymer. Three extracts, which were further characterized by size exclusion chromatography, gave two overlapping peaks. Structural characterisation of hemicellulosic polysaccharides, isolated with KOH, using specific enzyme hydrolysis, ion exchange chromatography (HPAEC) and matrix assisted laser desorption ionisation-time-of-flight (MALDI-TOF) mass spectroscopy, showed that sesame meal xyloglucan (XG) contained XXXG, XXFG and XXLG, and XLLG (named according to Fry et al., 1993) as the major building sub-units in the ratio of 1:0.9:0.3. Hydrolysis with endo-β-(1 → 4)-d-xylanase and analysis of the xylan derived oligosaccharides showed the presence of monomeric xylose (40%), xylobiose (46%) and acidic xylan oligosaccharides containing 4-O-methyl-d-glucuronic acid residues (14%).     

A Desymmetrization Approach to the Enantiopure syn/anti‐1,5‐Diols via Hydrolytic Kinetic Resolution (HKR) of Functionalized meso‐Bis‐Epoxides: Further Elaboration to syn/syn‐1,3,5‐Triols and Application to the Formal Synthesis of Cryptocarya Diacetate

A new approach has been developed for the synthesis of enantiopure syn/anti‐1,5‐diols by desymmetrization of functionalized meso‐bis‐epoxides using hydrolytic kinetic resolution (HKR). The usage of this protocol was demonstrated by converting syn‐1,5‐diols into syn/syn‐1,3,5‐triols and its subseqent application to the formal synthesis of cryptocarya diacetate.     

Particle fracture and plastic deformation in vanadium pentoxide powders induced by high energy vibrational ball-mill

An X-ray powder profile analysis in vanadium pentoxide powder milled in a high energy vibrational ball-mill for different lengths of time (0–250 h), is presented. The strain and size induced broadening of the Bragg reflection for two different crystallographic directions ([001] and [100]) was determined by Warren-Averbach analysis using a pattern-decomposition method assuming a Pseudo-Voigt function. The deformation process caused a decrease in the crystallite size and a saturation of crystallite size of ∼ 10 nm was reached after severe milling. The initial stages of milling indicated a propensity of size-broadening due to fracture of the powder particles caused by repeated ball-to-powder impact whereas with increasing milling time microstrain broadening was predominant. WA analysis indicated significant plastic strain along with spatial confinement of the internal strain fields in the crystallite interfaces. Significant strain anisotropy was noticed in the different crystallographic directions. A near-isotropy in the crystallite size value was noticed for materials milled for 200 h and beyond. The column-length distribution function obtained from the size Fourier coefficients progressively narrowed down with the milling time.     

Modeling of plasma spray coating process using statistical regression analysis

This study aimed to correlate outputs of a plasma spray coating process with its input parameters. Central composite design of experiments had been followed to conduct the experiments on plasma spray coating process, in order to collect its input–output data. The effects of four input parameters, namely primary gas flow rate, stand-off distance, powder flow rate, and arc current on three outputs (responses), such as thickness, porosity, and microhardness of the coatings, had been studied using non-linear statistical regression analysis. Such an analysis yielded the response equations, and viability of these equations had been tested on a set of experimentally obtained cases. The above four process parameters were found to have varying influences on different responses. However, all the above three responses were found to be significantly dependent on primary gas flow rate.     

Artificial neural network model in surface modification by EDM using tungsten–copper powder metallurgy sintered electrodes

Electro-discharge machining (EDM) is a widely accepted nontraditional machining process used mostly for machining materials difficult to machine by conventional shearing process. Surface modification by powder metallurgy sintered tools is an uncommon aspect of EDM. Of late, it is being explored by many researchers. In the present paper, attempts have been made to model the surface modification phenomenon by EDM with artificial neural networks. Two output measures, material transfer rate and average layer thickness, have been correlated with different process parameters and presented in the form of plots. The predicted results are matching well with the experimental results.     

Taguchi analysis of surface modification technique using W-Cu powder metallurgy sintered tools in EDM and characterization of the deposited layer

The present study describes an experimental research on surface modification during electrical discharge machining (EDM) by depositing a hard layer over the work surface of C-40 grade plain carbon steel using specially prepared powder metallurgy compact tools. The investigated process parameters were composition, compaction pressure, sintering temperature, pulse on-time, peak?Ccurrent setting, and duty factor. Measurements of deposited layer thickness, mass transfer rate, tool wear rate, surface roughness and microhardness were undertaken on the EDM-ed specimens. Different studies like X-ray diffraction, optical microscopy, scanning electron microscopy, and energy dispersive X-ray spectroscopy were carried out to ascertain the characteristics of the deposited layer on the work surface. These analyses confirmed the presence of the tool materials in the work surface layer. At first, an L-16 orthogonal array was applied as Taguchi DOE technique and the ANOVA was done to study the effects of pertinent process parameters. An optimum condition was achieved using overall evaluation criteria. Later on, a detailed study was carried out to get a smooth and regular deposition of material. The characterization of the deposited layer is presented. The deposited layer with a wide range of average layer thickness of 3?C785???m, enriched with tool materials (W and Cu) and with the formation of tungsten carbide, and having microhardness of 9.81?C12.75?GPa at the hardest zone was successfully deposited over the work surface.     

Note: Compact high voltage pulse transformer made using a capacitor bank assembled in the shape of primary

The experimental results of an air-core pulse transformer are presented, which is very compact (<10 Kg in weight) and is primed by a capacitor bank that is fabricated in such a way that the capacitor bank with its switch takes the shape of single-turn rectangular shaped primary of the transformer. A high voltage capacitor assembly (pulse-forming-line capacitor, PFL) of 5.1 nF is connected with the secondary of transformer. The transformer output voltage is 160 kV in its second peak appearing in less than 2 μS from the beginning of the capacitor discharge. The primary capacitor bank can be charged up to a maximum of 18 kV, with the voltage delivery of 360 kV in similar capacitive loads.     

Network-Wide Optimal Scheduling of Transit Systems Using Genetic Algorithms

The primary objective of any transit system is to provide a better level of service to its passengers. One of the good measures of level of service is the waiting time of passengers during their journey. The waiting time consists of an initial waiting time (the time a passenger waits to board a vehicle at his or her point of origin) and a transfer time (the time a passenger waits at a transfer station while transferring from one vehicle to another). An efficient schedule minimizes the overall transfer time (TT) of passengers transferring between different routes as well as the initial waiting time (IWT) of the passengers waiting to board the vehicle at their point of origin. This paper uses genetic algorithm (GA)—a search and optimization procedure—to find optimal/near-optimal schedules of vehicles in a transit network. The main advantage of using GA is that the transit network scheduling problem can be reformulated in a manner that is computationally more efficient than the original problem. Further, the coding aspect of GA inherently takes care of most of the constraints associated with the scheduling problem. Results from a number of test problems show that GAs are able to find optimal/near-optimal schedules with minimal computational resources.