Mechanism of alloying element vaporization during laser welding

Vaporization of alloying elements is a serious problem in the laser welding of many important engineering alloys. Since the available mass transfer correlations are not applicable for credible assessment of the rates of transport of vaporized species in the gas phase, the role of gas phase mass transfer in the overall vaporization of alloying elements was examined by conducting several critical experiments. The rates of transport of alloying elements in the weld pool were determined from numerically computed fluid flow fields. Since the weld pool is surrounded by plasma during laser welding, the role of plasma in the vaporization of alloying elements was physically modeled by allowing molten copper drops to vaporize isothermally both in the presence and absence of plasma. The transport of alloying elements in both liquid and gas phases was found to be rapid and the overall vaporization rates were controlled by the plasma influenced intrinsic vaporization of alloying elements at the weld pool surface. The experimentally obtained rates of vaporization of alloying elements from laser melted stainless steel weld pools were compared with the corresponding theoretically calculated values.     

Surface leakage currents in SiN/sub x/ passivated AlGaN/GaN HFETs

A novel guarded surface leakage test structure is used to isolate the surface and bulk leakage contributions to gate current in AlGaN/GaN HFETs. Passivation with various recipes of SiN/sub x/ always resulted in the commonly observed increase in gate leakage, which was found to be dominated by bulk leakage through the AlGaN. However, high temperature deposited SiN/sub x/ recipes gave a 1-2 orders reduction in surface leakage, whereas low temperature deposition gave an increase. Gate lag measurements were found to correlate closely with the surface leakage component, giving direct evidence that the key device problem of current slump is associated with current flow at the AlGaN surface.     

Bioprocess applications of model-based estimation techniques

The last decade has seen the development of a number of approaches for estimating those variables which are difficult to measure on-line in industrial process situations. Whilst a range of techniques is available, a common element is the use of process knowledge in the form of a system model. In the case of bioprocess systems, although a large range of models has been presented in the literature, their use in estimation schemes on an industrial scale has been limited. A number of reasons can be identified for their low level of utilisation. Of particular significance is the uncertainty which exists in quantifying system performance and the process-model mismatch which inevitably results. The level of ‘pre-defined model’ uncertainty, together with the knowledge gained during the course of the fermentation, serves to dictate estimator structure. The paper considers a range of estimation strategies and contrasts, through industrial applications, their performance characteristics and utility.     

Religiosity and emotional disturbance: A test of Ellis's thesis in his own counseling center.

Assessed the validity of A. Ellis's (1971, 1973, 1981) contention that being religious was negatively correlated with mental health. 28 very religious, 34 atheist, and 33 religiously-neutral individuals seeking consultation were compared on the frequency and number of 8 reported problems. Contrary to Ellis's prediction, there were no significant differences among the groups. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

45% efficient silicon photovoltaic cell under monochromatic light

Improvements in the performance of silicon photovoltaic cells for solar applications are adapted for nonsolar photovoltaic applications. Improved monochromatic light efficiencies above 45% are reported including efficiencies close to 40% for relatively long-wavelength (1.064 μm) light as produced by neodymium-doped yttrium-aluminum garnet (Nd:YAG) lasers     

Yodel: A Yield Stress Model for Suspensions

A model for the yield stress of particulate suspensions is presented that incorporates microstructural parameters taking into account volume fraction of solids, particle size, particle size distribution, maximum packing, percolation threshold, and interparticle forces. The model relates the interparticle forces between particles of dissimilar size and the statistical distribution of particle pairs expected for measured or log-normal size distributions. The model is tested on published data of sub-micron ceramic suspensions and represents the measured data very well, over a wide range of volume fractions of solids. The model shows the variation of the yield stress of particulate suspensions to be inversely proportional to the particle diameter. Not all the parameters in the model could be directly evaluated; thus, two were used as adjustable variables: the maximum packing fraction and the minimum interparticle separation distance. The values for these two adjustable variables provided by the model are in good agreement with separate determinations of these parameters. This indicates that the model and the approximations used in its derivation capture the main parameters that influence the yield stress of particulate suspensions and should help us to better predict changes in the rheological properties of complex suspensions. The model predicts the variation of the yield stress of particulate suspensions to be inversely proportional to the particle diameter, but the experimental results do not show a clear dependence on diameter. This result is consistent with previous evaluations, which have shown significant variations in this dependence, and the reasons behind the yield stress dependence on particle size are discussed in the context of the radius of curvature of particles at contact.     

Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the     

Stability, in-Vitro and in-Vivo Release Studies from Metronidazole Ointments

The influence of ointment formulation on the stability, the in-vitro release and the in-vivo absorption through the skin of rabbits was investigated. The choice of the selected ointments has no influence on the drug stability with the exception of an acidified emulsion base. A good correlation between in-vitro release and in-vivo absorption was found revealing that metronidazole was quickly released and effectively absorbed from a polyethylene glycol base.