Simulation of the initial stages of nucleation and growth of Au/NaCl(100)

The results of a computer simulation of the initial stages of the nucleation and growth of gold on NaCl(100) are presented. A potential energy scaling Monte Carlo model employing a 50 × 50 array, mobile monomers, dimers and trimers, and gold atom vertical “roll up” was used. The parameters in the model were obtained from the work of Robinson and Robins, other published sources and/or found by calculation. Simulations of the migration of single gold adatoms over the surface permitted the determination of the diffusion coefficient as a function of the reciprocal temperature which returned the same activation energy given by the potential field, thus indicating the consistency of the model. Initial cluster densities were determined using deposition rates of R_d = 10¹⁵cm^-2s^-1 and R_d = 10¹⁴cm^-2s^-1 over the temperature range T=200–425 K. Initial cluster growth was found to occur primarily by surface phase transport and resulted in clusters that were shaped like very thin disks. Using the equations from the work of Velfe and coworkers, calculations were made to extrapolate the computer simulation data in order to permit an indirect comparison with the data of Robinson and Robins. Good agreement was achieved. Initial condensation coefficients determined over a 250 ms interval showed that α ≈ 0 at T > 425 K and α ≈ 1 at T < 325 K for a deposition rate of R_d=10¹⁵ cm^-2 s^-1.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Online and Offline Rotary Regression Analysis of Torque Estimator for Switched Reluctance Motor Drives

A new torque estimator for switched reluctance motor (SRM) drives based on 2-D rotary regression analysis is presented in this paper. The proposed torque estimator is composed of a bicubic regressive polynomial as a function of rotor position and input current. The regressive coefficients can be computed offline or online from the torque characteristics acquired either experimentally or from numerical computation. Furthermore, a torque estimation method by taking mutual coupling into consideration is proposed. It can be seen that the estimated and experimentally obtained self-coupling and mutual-coupling torque characteristics are in good agreement with each other. In addition, the dynamic torque waveforms with and without the mutual coupling, estimated by the proposed estimator, are found to be virtually the same as those obtained from the bicubic spline interpolation for SRM drives with single-pulse voltage, hysteresis current chopping, as well as with voltage pulse width modulation control. The success of all the case studies being reported is a good validation of the usefulness and accuracy of the proposed real-time torque estimator that, as described in this paper, can be used to quickly estimate the instantaneous output torque of SRM drives.     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。     

3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

A process-dependent real-time controller for sequencing batch reactor plants: results of full-scale operation.

This paper presents results of a research project, in which a process-dependent real-time control (RTC) strategy for a sequencing batch reactor plant was realised in full-scale. The cycle controller is based on NH4 analysers, NO3 probes, TSS probes and sludge level probes. With this new RTC strategy it was possible to increase the treatment capacity by 50%. By implementation of the new controller the TN, TP and NH4-N treatment efficiency could be improved significantly, too. The treatment efficiency concerning COD is comparable.