Wavelength-tunable 40-GHz picosecond harmonically mode-locked fiber laser source

We demonstrate a novel 40-GHz mode-locked fiber laser that utilizes a single active device to provide both gain and mode-locking. The laser produces pulses as short as 2.2 ps, is tunable over a 27-nm band centered at 1553 nm, and exhibits long-term stability without cavity-length feedback control. The pulse train at 1556 nm was used in a 40-Gb/s transmission experiment over 45 km with a low 0.4-dB power penalty.     

Solutions to a combined problem of excessive hydrogen sulfide in biogas and struvite scaling.

The Woodman Point Wastewater Treatment Plant (WWTP) in Western Australia has experienced two separate problems causing avoidable maintenance costs: the build-up of massive struvite (MgNH4PO4. 6H2O) scaling downstream of the anaerobic digester and the formation of hydrogen sulfide (H2S) levels in the digester gas to levels that compromised gas engine operation and caused high operating costs on the gas scrubber. As both problems hang together with a chemical imbalance in the anaerobic digester, we decided to investigate whether both problems could be (feasibly and economically) addressed by a common solution (such as dosing of iron solutions to precipitate both sulfide and phosphate), or by using separate approaches. Laboratory results showed that, the hydrogen sulfide emission in digesters could be effectively and economically controlled by the addition of iron dosing. Slightly higher than the theoretical value of 1.5 mol of FeCl3 was required to precipitate 1 mol of dissolved sulfide inside the digester. Due to the high concentration of PO4(3-) in the digested sludge liquor, significantly higher iron is required for struvite precipitation. Iron dosing did not appear an economic solution for struvite control via iron phosphate formation. By taking advantage of the natural tendency of struvite formation in the digester liquid, it is possible to reduce the risk of struvite precipitation in and around the sludge-dewatering centrifuge by increasing the pH to precipitate struvite out before passing through the centrifuge. However, as the Mg2+/PO4(3-) molar ratio in digested sludge was low, by increasing the pH alone (using NaOH) the precipitation of PO4(3-) was limited by the amount of cations (Ca2+ and Mg2+) available in the sludge. Although this would reduce struvite precipitation in the centrifuge, it could not significantly reduce PO4(3-) recycling back to the plant. For long-term operation, maximum PO4(3-) reduction should be the ultimate aim to minimise PO4(3-) accumulation in the plant. Magnesium hydroxide liquid (MHL) was found to be the most cost-effective chemical to achieve this goal. It enhanced struvite precipitation from both, digested sludge and centrate to the point where more than 95% PO4(3-) reduction in the digested sludge was achieved.     

Preschool Competency in Context: An Investigation of the Unique Contribution of Child Competencies to Early Academic Success.

The present concurrent study combined developmental and ecological considerations to examine the unique contribution of multiple preschool competencies to an indicator of early academic success. Participants included 195 Head Start children from 32 classrooms representative of a large, urban Head Start program. Dimensional (variable-centered) analyses revealed 3 distinct classroom competency dimensions (i.e., General Classroom Competencies, Specific Approaches to Learning, and Interpersonal Classroom Behavioral Problems). The first 2 of these dimensions were found to be uniquely associated with early academic success. Findings from typological (person-centered) analyses supported the dimensional findings. Typological analyses revealed 7 profiles of classroom competency distinguished by high scores on the dimensions of General Competencies and Approaches to Learning, and these profiles were found to relate differentially to the indicator of early academic success. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

Improvement of AlGaInP light emitting diode by sulfide passivation

The brightness of AlGaInP light emitting diodes (LEDs) has been raised by a factor of 1.12 at 20 mA by sulfide passivation. Meanwhile, the sulfide also can decrease leakage current of AlGaInP LEDs at -2 V to nearly one thousandth of that in the as-fabricated device. The possible causes for the brightness increase of AlGaInP LEDs after sulfide treatment including surface roughness, reduction of Fresnel loss, and effective injection of carriers were demonstrated.     

Hopping and optical absorption of electrons in nano-porous crystal 12CaO·7Al2O3

Recently it has been discovered that a nano-porous main group oxide 12CaO·7Al₂O₃ (C12A7) can be converted from a wide-gap insulator to a good transparent conductor. Using ab initio modelling we explain good conductivity of this material by very small barriers for hopping of localised electrons between neighbouring positive cages. We show that optical absorption of C12A7 in infrared region and at energies higher than 2.7 eV is due to inter-cage and intra-cage electron transitions, respectively. The proposed mechanisms can be useful in further search for conducting transparent media.     

Impact of lead-free soldering processes on the performance of signal relay contacts

Various legislations, rules and regulations in Europe [Restrictions of the use of certain hazardous substances in electrical and electronic equipment (ROHS)] and Japan (Recycling Law for Home Electric Appliances) have either targeted restrictions or a full ban on the use of lead, to be enforced from 2001, 2005, and 2006 onwards. Next to these regulations, marketing arguments are becoming more and more important for so called "GREEN" products. Up to now, mainly tin-lead alloys have been used in electronics. The process temperatures usually applied have been in the range of 230/spl deg/C. All currently discussed lead-free alternatives for professional electronics need process temperatures which are at least 30/spl deg/C higher. In addition, the process duration is significantly longer. The combination of higher process temperatures and longer duration together results in a significant thermal stress on the precision mechanics of the relay. In order to guarantee proper functioning of the relay after the solder process with maximum process temperatures of 255/spl deg/C, the dimensional changes of the plastic parts must be less than a few micrometers in order to guarantee stable contact forces. The outgassing of the used insulating and sealing materials must be minimal in order not to pollute or contaminate the contacts. With the lead-free version of the IM relay, an identical performance and the same reliability during electrical and climatic endurance tests can be expected, even though relays were processed with typical lead-free soldering processes with temperatures up to 255/spl deg/C.