Amine-containing olefin copolymer with CO2-switchable oil absorption and desorption

Global decrease in crude oil resources and frequent crude oil leaks cause the energy crisis and ecological pollution. The absorption and release of leaked crude oil through absorption materials are a necessary process for environmental protection and recycling. In this article, a CO₂-responsive olefin copolymer was obtained by copolymerization of styrene and an amine-containing olefin monomer. The structure of resultant copolymer was characterized by FTIR; thermal properties and CO₂-responsive morphology changes were determined by DSC/TGA and SEM, respectively. Copolymers had certain absorption capacity for toluene with absorption rate up to 180.0%. The absorbed toluene could be released upon CO₂ stimulation with desorption rate up to 84.6%. The CO₂-responsive copolymer could be regenerated through a simple heating process and showed stable absorption–desorption performance even after being recycled for 4 times. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47439.     

Thermoplastic and low dielectric constants polyimides based on BPADA-BAPP

ABSTRACT

The thermoplastic and low dielectric constants polyimides were introduced. The polyimides were prepared by pyromellitic dianhydride (PMDA) or 4,4?-(4,4?-Isopropylidenediphenoxy)diphthalic anhydride (BPADA) as anhydride monomer and 4,4?-oxydianiline (ODA) or 2,2-bis(4-(4-aminephenoxy)phenyl)propane (BAPP) as amine monomer. The polyimides were well characterized by FT-IR, thermogravimetric analysis, dynamic thermomechanical analysis, dielectric measurement, and tensile test. The dielectric constants were 2.32–2.95 compared with 3.10 of ODA-PMDA polyimide, while partly polyimides were thermoplastic. The results indicated anhydride monomers, containing lateral methyl groups, made polyimides become thermoplastic. The results of molecular simulations via Materials Studio also proved this conclusion.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

内插法在相关干涉仪测向体制中的应用

测向误差的减小一直以来都是无线电测向精度提高的一个难点,对于不同的测向体制所采用的减小测向误差的方法都不尽相同。本文主要介绍的是相关干涉仪测向体制的基本原理以及通过内插法的应用来减小测向误差的方法。     

文献计量视角下健康人力资本研究动态分析

通过文献计量方法从样本选取、研究动态分析、主题分布三方面对健康人力资本发展现状及热点问题进行总结.研究结果表明,自2004年开始该领域所属学科种类和期刊源日益丰富,并形成合著度较高的核心作者群体,健康人力资本研究成为人力资本领域的研究热点,健康人力资本与经济增长或收入的关系、健康人力资本指标体系的构建和居民健康人力资本收入效应的测算等问题都成为当前和未来的研究重点.     

3-三氟甲基-5,6,7,8-四氢-1,2,4-三唑[4,3-α]吡嗪盐酸盐的合成

乙二胺与氯乙酸乙酯经取代、环合反应制得2-哌嗪酮,2-哌嗪酮与Boc酸酐进行氨基保护反应后,再与五硫化二磷进行硫代反应制得4-(N-叔丁氧羰基)-2-哌嗪硫酮,其与三氟乙酰肼经取代、环合、脱叔丁氧羰基成盐,得标题化合物,总收率为45.7%(以氯乙酸乙酯计)。为磷酸西他列汀中间体的工业化生产提供了一条较理想的工艺路线。     

古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。