Biodiesel from rapeseed oil,methanol and KOH. 3. Analysis of composition of actual reaction mixture

Detailed analysis is described of the samples taken after suitable reaction times from the actual reaction mixture during the production of biodiesel fuel using methanolysis of rapeseed oil catalyzed by KOH. Three methods for stoppage of reaction (neutralisation of catalyst, dilution by two suitable solvents) in the sample are used. The contents of mono‐, di‐ and triacylglycerols, methylesters of fatty acids (biodiesel) and potassium salts of fatty acids of rapeseed oil, glycerol (by HPLC method), basicity (by potentiometric titration) and water (by GC and Karl‐Fischer method) in the samples are determined. An example of these determinations is described.     

An effect of iron(III) oxides crystallinity on their catalytic efficiency and applicability in phenol degradation—A competition between homogeneous and heterogeneous catalysis

Catalytic efficiency, stability and environmental applicability of five iron(III) oxide nanopowders differing in surface area and crystallinity were tested in degradation of concentrated phenolic aqueous solutions (100 g/L) at mild temperature (30 °C), initially almost neutral pH and equimolar ratio of hydrogen peroxide and phenol. The catalyst properties were easily controlled by varying in reaction time during isothermal treatment of ferrous oxalate dihydrate in air at 175 °C. Although the catalytic efficiency clearly increases with the surface area of the nanopowders, it is not due to the solely heterogeneous catalytic mechanism as would be expected. The amorphous Fe₂O₃ nanopowders possessing the largest surface areas (401 m² g⁻¹, 386 m² g⁻¹) are the most efficient catalysts evidently due to their highest susceptibility to leaching in acidic environment arising as a consequence of phenol degradation products. Thus, these amorphous samples act partially as homogeneous catalysts, which was confirmed by a high concentration of leached Fe(III) ions in the solution (19 ppm). The crystalline hematite (α-Fe₂O₃) samples, varying in surface area between 337 m² g⁻¹ and 245 m² g⁻¹, are generally less efficient when compared to the amorphous powders, however their catalytic action is almost exclusively heterogeneous as only 3 ppm of leached Fe(III) was found in the reaction systems catalyzed by nanohematite samples. A significant difference in relative contributions of heterogeneous and homogenous catalysis was definitely established in buffered reaction systems catalyzed by amorphous Fe₂O₃ and nanocrystalline hematite. The nanohematite sample exhibiting the highest heterogeneous action was tested at decreased initial phenol concentration (10 g/L), which is closer to the real contents of phenol in waste waters, and at different hydrogen peroxide/phenol molar ratios to consider its environmental applicability. At the hydrogen peroxide/phenol ratio equal to 5, no traces of the leached iron were detected and the phenol conversion of 84% was reached. Moreover, such a high degree of conversion is accompanied by a decrease of the chemical oxygen demand (COD) from the initial value of 11.23 g/L to 4.22 g/L after 125 min. This fact indicates that the considerable fraction of primary reaction products was totally degraded.     

Comparison of Isolated Indentation and Grid Indentation Methods for HVOF Sprayed Cermets

This paper compares the results of two approaches of instrumented indentation for characterization of mechanical properties of HVOF coatings. Three types of HVOF sprayed coatings (Cr₃C₂-NiCr, WC-Co, (Ti, Mo)(C,N)-NiCo) were investigated by the means of isolated nanoindentation and grid indentation methods. The results of the isolated indentation revealed hardness and elastic modulus of the individual phases in very good agreement with the corresponding bulk material. The grid indentation method, based on statistical evaluation of a large number of indentations, was influenced by the carbide-matrix interface, which gave rise to a third peak apart from the two peaks corresponding to the carbides and metallic matrix. As a consequence, the bimodal Gaussian fit was insufficient and a trimodal fit had to be used. The results extracted from low load grid nanoindentations were quite close to the results of isolated indentations whereas higher load grid nanoindentation revealed overall properties of the coating.     

Application of Structure-Based Models of Mechanical and Thermal Properties on Plasma Sprayed Coatings

Mechanical and thermal properties of thermal sprayed coatings, especially ceramics, are strongly influenced by cracks and pores that are present in the coating microstructure. In the recent past, there have been efforts to find an analytical model describing the coating properties based on the microstructural characteristics. Various analytical models were developed and published in the literature. In this study, several major models were applied to ceramic and metal coatings to describe their elastic modulus and thermal conductivity. The sensitivity of the models to the variations in the microstructure and relevancy of their use in specific cases were examined. The results were compared with those obtained by FEM modeling and experimentally measured values.     

Separation of Indium from Acid Sulfate-Containing Solutions by Ion Exchange with Impregnated Resins

Indium separation using ion exchange resins from acidic polymetallic and very diluted solutions are investigated. Since the selectivity of commercial ion exchange resins have proven to be too low for an effective separation from solutions with high content of other metals, Lewatit® TP 208 was impregnated with common extractants to enhance its properties. By resin impregnation with D2EHPA and Cyanex 272, not only the selective indium recovery was reached but also the resin capacity was increased approx. two times. The best loading and elution performance were shown by Cyanex 272-impregnated Lewatit® TP 208, increasing the indium purity in the eluate from 0.75 % to 85 %.     

Numerical estimation of hydrogen storage limits in carbon-based nanospaces

Theoretical limits of the hydrogen adsorption in carbon nanospaces are modeled using Monte Carlo simulations. A detailed analysis of storage capacity of slit pores has been performed as a function of the pore size, gas pressure (up to 100 bars) and temperature of adsorption (77 and 298 K). The H₂-slit wall interaction has been modeled assuming energies of adsorption ranging from 4.5 kJ/mol (pure graphene surface) to 15 kJ/mol (hypothetical chemically modified graphene). The quantum nature of H₂ has been incorporated in the calculations using the Feynman-Hibbs approach. It has been shown that in a hypothetical chemically modified porous carbon, with energy of adsorption of 15 kJ/mol or higher and pore size between 0.8 and 1.1 nm, the gravimetric and volumetric storage capacity can achieve targets required for practical applications. The relation between the energy of adsorption and the effective delivery has been discussed.     

Temperature‐Dependent Exciton and Trap‐Related Photoluminescence of CdTe Quantum Dots Embedded in a NaCl Matrix: Implication in Thermometry

Temperature‐dependent optical studies of semiconductor quantum dots (QDs) are fundamentally important for a variety of sensing and imaging applications. The steady‐state and time‐resolved photoluminescence properties of CdTe QDs in the size range from 2.3 to 3.1 nm embedded into a protective matrix of NaCl are studied as a function of temperature from 80 to 360 K. The temperature coefficient is found to be strongly dependent on QD size, with the highest sensitivity obtained for the smallest size of QDs. The emission from solid‐state CdTe QD‐based powders is maintained with high color purity over a wide range of temperatures. Photoluminescence lifetime data suggest that temperature dependence of the intrinsic radiative lifetime in CdTe QDs is rather weak, and it is mostly the temperature‐dependent nonradiative decay of CdTe QDs which is responsible for the thermal quenching of photoluminescence intensity. By virtue of the temperature‐dependent photoluminescence behavior, high color purity, photostability, and high photoluminescence quantum yield (26%–37% in the solid state), CdTe QDs embedded in NaCl matrices are useful solid‐state probes for thermal imaging and sensing over a wide range of temperatures within a number of detection schemes and outstanding sensitivity, such as luminescence thermochromic imaging, ratiometric luminescence, and luminescence lifetime thermal sensing.