Calibrating multibody ulno-humeral joint cartilage using a validated finite element model

Correct prediction of contact characteristic in multibody models is a challenging issue, which requires both employing an appropriate contact model and choosing its corresponding contact parameters. This study employed two subject specific multibody models of the ulno-humeral joint where the humerus cartilage was discretized and interacted with the ulna cartilage through a deformable contact. Parameters for the deformable contact were optimized by matching the maximum predicted contact pressure in the multibody models with contact pressures predicted in identical finite element models under axial 110 N compressive load. The performance of the optimized contact parameters and employed approach was evaluated under two other loading conditions of 80 and 140 N. Moreover, the effect of discretized element size on the contact prediction was also addressed. After optimization of the contact parameters, the difference between the multibody and FE models in terms of peak and average contact pressure, and contact area was significantly reduced (more than a factor of 10). Smaller discretization size of the humerus cartilage in the multibody models resulted in better predictions especially on highly curved regions. However, the optimized parameters of our study were different between the two elbows. This indicates that optimized contact parameters can be different not only among different joints, but also among different specimens and optimization conditions. Therefore, in order to improve contact predictions, separate contact optimization should be performed for each subject.     

Intermittent Audio Failure Analysis of a Remote Speaker-Microphone for a Two-Way Radio

This paper presents a case study of an intermittent audio failure analysis of a remote speaker-microphone module for a two-way radio. A root cause analysis was undertaken to identify probable causes of the intermittent failure, followed by a series of experiments to determine the strength and the intermittent audio failure load of cable components and the fully assembled cable. The combined experimental and finite element results demonstrated that the main contributor of the intermittent audio failure was the micro surface cracks on the copper conductor strands. In addition, the combination of the component materials and design of the cable have also contributed to the non-uniform state of residual stress induced in the copper conductors which have reduced the ability of the copper conductors to withstand the normal handling load under the influence of micro surface cracks.     

Nanostructured materials for water desalination

Desalination of seawater and brackish water is becoming an increasingly important means to address the scarcity of fresh water resources in the world. Decreasing the energy requirements and infrastructure costs of existing desalination technologies remains a challenge. By enabling the manipulation of matter and control of transport at nanometer length scales, the emergence of nanotechnology offers new opportunities to advance water desalination technologies. This review focuses on nanostructured materials that are directly involved in the separation of water from salt as opposed to mitigating issues such as fouling. We discuss separation mechanisms and novel transport phenomena in materials including zeolites, carbon nanotubes, and graphene with potential applications to reverse osmosis, capacitive deionization, and multi-stage flash, among others. Such nanostructured materials can potentially enable the development of next-generation desalination systems with increased efficiency and capacity.     

Influence of bias voltage on the optical and structural properties of nc-Si:H films grown by layer-by-layer (LBL) deposition technique

The effects of applying a positive bias of 25 to 100 V on the optical, structural and photoluminescence (PL) properties of hydrogenated nanocrystalline silicon (nc-Si:H) films produced by layer-by-layer (LBL) deposition technique has been studied. Optical characterization of the films has been obtained from UV-VIS-NIR spectroscopy measurements. Structural characterization has been performed using X-ray diffraction, micro-Raman spectroscopy and field emission scanning electron microscope (FESEM). PL spectroscopy technique has been used to investigate the PL properties of the films. In general, the films formed shows a mixed phase of silicon (Si) nanocrystallites embedded within an amorphous phase of the Si matrix. The crystalline volume fraction and grain size of the Si nanocrystallites have been shown to be strongly dependent on the applied bias voltage. High applied bias voltage enhances the growth rate of the films but reduces the refractive index and the optical energy gap of the films. Higher crystalline volume fraction of the films prepared at low bias voltages exhibits room temperature PL at around 1.8 eV (700 nm).     

Generalized viscoelastic designer functionally graded auxetic materials engineered/tailored for specific task performances

For arbitrary linear Kelvin model viscoelastic constitutive relations, generalized analyses based on collocation, least squares, Lagrangean multipliers, calculus of variation and inverse formulations are presented for determining viscoelastic designer material properties tailored and engineered to be best suited for specific boundary and loading conditions and their time histories. Optimum 3-D anisotropic designer materials, including auxetic viscoelastic functionally graded ones, are studied to minimize thermal stresses, creep buckling, creep rates, deflections, aero- and hydro- dynamic noise and static and dynamic aero-viscoelastic effects while concurrently lowering failure probabilities and extending structural survival times and maximizing or minimizing energy dissipation and its rate. The analyses are formulated for single structural elements as well as the entire structure. Extensions to the entire vehicle that incorporate aerodynamics, stability and control are discussed and the dimensions of computational requirements are estimated.     

Effect of doping (C or N) and co-doping (C+N) on the photoactive properties of magnetron sputtered titania coatings for the application of solar water-splitting

The photocatalytic splitting of water into hydrogen and oxygen using a photoelectrochemical (PEC) cell containing titanium dioxide (TiO2) photoanode is a potentially renewable source of chemical fuels. However, the size of the band gap (-3.2 eV) of the TiO2 photocatalyst leads to its relatively low photoactivity toward visible light in a PEC cell. The development of materials with smaller band gaps of approximately 2.4 eV is therefore necessary to operate PEC cells efficiently. This study investigates the effect of dopant (C or N) and co-dopant (C+N) on the physical, structural and photoactivity of TiO2 nano thick coating. TiO2 nano-thick coatings were deposited using a closed field DC reactive magnetron sputtering technique, from titanium target in argon plasma with trace addition of oxygen. In order to study the influence of doping such as C, N and C+N inclusions in the TiO2 coatings, trace levels of CO2 or N2 or CO2+N2 gas were introduced into the deposition chamber respectively. The properties of the deposited nano-coatings were determined using Spectroscopic Ellipsometry, SEM, AFM, Optical profilometry, XPS, Raman, X-ray diffraction UV-Vis spectroscopy and tri-electrode potentiostat measurements. Coating growth rate, structure, surface morphology and roughness were found to be significantly influenced by the types and amount of doping. Substitutional type of doping in all doped sample were confirmed by XPS. UV-vis measurement confirmed that doping (especially for C doped sample) facilitate photoactivity of sputtered deposited titania coating toward visible light by reducing bandgap. The photocurrent density (indirect indication of water splitting performance) of the C-doped photoanode was approximately 26% higher in comparison with un-doped photoanode. However, coating doped with nitrogen (N or N+C) does not exhibit good performance in the photoelectrochemical cell due to their higher charge recombination properties.     

Europium (III) PVC membrane sensor based on N-pyridine-2-carboxamido-8-aminoquinoline as a sensing material

Conductometric study in acetonitrile solution shows the selectivity of PCQ toward europium ion. Therefore, a new europium PVC membrane electrode was prepared based on N-pyridine-2-carboxamido-8-aminoquinoline (PCQ) as an ion carrier. The electrode has a wide concentration range from 1.0 × 10^− 2 and 1.0 × 10^− 6 mol L^− 1, Nernstian slope of 19.8 ± 0.3 mV per decade and a detection limit of 6.4 × 10^− 7 mol L^− 1. The potentiometric response is pH independent in the range of 2.4-7.4. The proposed sensor has a relatively fast response time less than 10 s and it can be used for at least 2 months without any considerable divergence in its potentials. The proposed electrode revealed good selectivity toward europium ion in comparison with variety of other metal ions. The practical utility of the electrodes has been demonstrated by their use as indicator electrodes in the potentiometric titration of Eu^3 + ions with EDTA and for determination of Eu^3 + ion concentration in mixtures of two and three different ions.     

Pressure dependent structural and optical properties of silicon carbide thin films deposited by hot wire chemical vapor deposition from pure silane and methane gases

Silicon carbide (SiC) thin films were deposited using hot wire chemical vapor deposition technique from silane (SiH₄) and methane (CH₄) gas precursors. The effect of deposition pressure on structural and optical properties of SiC films was investigated. Various spectroscopic methods including Fourier transform infrared spectroscopy, Raman scattering spectroscopy, Auger electron spectroscopy, and UV–Vis–NIR spectroscopy were used to study these properties. Films deposited at low deposition pressure were Si-rich, and were embedded with nano-crystals of silicon. These films showed strong absorption in the visible region and had low energy band gaps. Near stoichiometric SiC film, were formed at intermediate deposition pressure and these films were transparent in the visible region and exhibited a wide optical band gap. High deposition pressures caused inhomogeneity in the film as reflected by the increase in disorder parameter and low refractive index of the films. This was shown to be due to formation of sp ² carbon clusters in the film structure.     

A Real-Time Sequential Deep Extreme Learning Machine Cybersecurity Intrusion Detection System

In recent years, cybersecurity has attracted significant interest due to the rapid growth of the Internet of Things (IoT) and the widespread development of computer infrastructure and systems. It is thus becoming particularly necessary to identify cyber-attacks or irregularities in the system and develop an efficient intrusion detection framework that is integral to security. Researchers have worked on developing intrusion detection models that depend on machine learning (ML) methods to address these security problems. An intelligent intrusion detection device powered by data can exploit artificial intelligence (AI), and especially ML, techniques. Accordingly, we propose in this article an intrusion detection model based on a Real-Time Sequential Deep Extreme Learning Machine Cybersecurity Intrusion Detection System (RTS-DELM-CSIDS) security model. The proposed model initially determines the rating of security aspects contributing to their significance and then develops a comprehensive intrusion detection framework focused on the essential characteristics. Furthermore, we investigated the feasibility of our proposed RTS-DELM-CSIDS framework by performing dataset evaluations and calculating accuracy parameters to validate. The experimental findings demonstrate that the RTS-DELM-CSIDS framework outperforms conventional algorithms. Furthermore, the proposed approach has not only research significance but also practical significance.     

Implementation of high speed optical universal logic gates using the electro-optic effect-based Mach–Zehnder interferometer structures

The universal logic gates are the most important logic gates responsible for optimized design of different types of complex digital logic circuits. It is of great interest to implement the function of universal logic gates such as NAND and NOR logic gates using the concepts of electro-optic effect. The smart use of electro-optic effect can provide very effective optical power switching devices. The implementation of universal logic gates operation in the optical domain can improve the performance of the devices and includes the advantages of the optical communication system. The proper configuration of Mach–Zehnder interferometer working on the principle of electro-optic effect can provide the optical responses equivalent to the NAND and NOR logic gates. The proposed devices can be analyzed to check the various performance affecting parameters in order to specify the physical parameters.