Generation of square and triangular wave with independently controllable frequency and amplitude using OTAs only and its application in PWM

This paper presents a self-generating square/triangular wave generator using only the CMOS Operational Transconductance Amplifiers (OTAs) and a grounded capacitor. The output frequency and amplitude of the proposed circuit can be independently and electronically adjusted. The proposed circuit validates its advantage by consuming less amount of power, which is about 71.3 µW. The theoretical aspects are authentically showcased using the PSPICE simulation results. The performance of the proposed circuit is also verified through pre layout and post layout simulation results using the 90 nm GPDK CMOS parameters. A prototype of this circuit has been made using commercially available IC CA3080 for experimental verification. Experimentation also gives the similar output as per the theoretical proposition. The designed circuit is also made applicable to perform pulse width modulation (PWM).     

Retrieval of thermal properties in a transient conduction–radiation problem with variable thermal conductivity

This article reports an inverse analysis of a transient conduction–radiation problem with variable thermal conductivity. Simultaneous retrieval of parameters is accomplished by minimizing the objective function represented by the square of the difference between the measured and the assumed temperature fields. The measured temperature field is calculated from the direct method involving the lattice Boltzmann method (LBM) and the finite volume method (FVM). In the direct method, the FVM is used to obtain the radiative information and the LBM is used to solve the energy equation. With perturbations imposed on the measured temperature data, minimization of the objective function is achieved with the help of the genetic algorithm (GA). The accuracies of the retrieved parameters have been studied for the effects of the genetic parameters such as the crossover and the mutation rates, the population size, the number of generations and the effect of noise on the measured temperature data. A good estimation of parameters has been obtained.     

Fabrication of Food Grade Vitamin E Nanoemulsion by Low Energy Approach,Characterization and Its Application

The present study was carried out to fabricate the food grade vitamin E acetate nanoemulsion using edible mustard oil and to evaluate its improved bioactivities. A food-grade vitamin E acetate nanoemulsion was fabricated using the edible mustard oil and surfactant Tween-80. Flocculation was not observed for 15 days. The nanoemulsion was characterized for droplet morphology and size distribution using atomic force microscope and zetasizer, respectively. We observe a stable nanoemulsion of spherical morphology and a size distribution of 86.45 ± 3.61 nm. Further, the high-performance liquid chromatography method was used to determine the vitamin E acetate concentration and encapsulation efficiency for the stable nanoemulsion. These nanoemulsions showed improved bioactivity, antioxidant, and antimicrobial activity and could be potentially used to increase the shelf life of fruit juice.     

A summary of ring rolling technology—I. Recent trends in machines, processes and production lines

Ring rolling process is widely used in the production of seamless rings for automotive and aerospace industry. This paper presents a summary of the ring rolling technology: machine and process types; process considerations; and examples of ring rolling lines. In this technology survey, recent trends in ring rolling machines and processes are emphasized. This survey will be specially valuable for industry personnel engaged with the selection and implementation of ring rolling lines and process planning engineers working with ring rolling companies. It will also provide adequate background to researchers initiating research in the mechanics of the ring rolling process.     

引领新一代高级封装的光刻技术

在当今飞速发展的电子环境中，芯片制造商和封装技术供应商们发现传统的前段制造设备，诸如光刻步进器等，可能会实现成本高效的后段工艺流程（BEOL）器件封装。尽管高级封装市场的发展空间最初是被PCs行业的蓬勃发展带动起来的，但是现在它们已经不再是主要的增长催化因素。通信以及手持设备，如手机、PDAs（个人数字助理）、便携式游戏机以及个人通讯系统正在成为新增长阶段的推动因素。随着数字消费应用的爆炸式发展一陛能和波形系统成为必须启用高级封装（AP）技术的必要条件。在未来五年内，预计通讯芯片组、图形处理器、集成无源元件以及高速PC内存元件将成为AP技术的主要诉求。随着领先的逻辑芯片制造商们需求量的不断增大，我们共同见证了AP市场的成长过程。然而，这一细分市场的另一个转折点可能会来自高速PC内存元件对高级封装技术的诉求。     

Past developments and future trends in the rotary or orbital forging process

Rotary forging is a relatively new manufacturing process with potential for cost-effective applications, especially in cold forging of intricate parts to net shape. In this paper orbital forging and axial die rolling processes are included as subsets of rotary forging while radial forging, also known as rotary forging, has been excluded; these decisions are primarily based on die kinematics. Because of its recent origins, the rotary forging process is first described. Then, a historical perspective is provided to trace its recent origins. The machines are classified based on die kinematics. Die kinematics influence the stick-slip or position discrepancy behavior of the different machine types and have deep implications on the die filling and accuracy capabilities of these machines. Rotary forging machines currently in operation in the U.S. and their applications are presented in greater detail. The discussion on future applications and potential research issues is primary based on the author’s own perception of future trends in this emerging field. The author is with.     

Effects of thermal load on wheel–rail contacts: A review

This article presents a technical review on the effects of thermal loads evolved at the wheel–rail–brake contact interfaces. These dynamic contact interfaces develop heat transfer conditions of widely varied thermal level. Their modeling to identify the sources for a variety of defect formation, observable on wheel tread or rail surface, is very important. The railway system, in general, has to bear axle load, friction load, and thermal load arising from their contact conditions in addition to traction and dynamic loads. The defects arising from the interaction of thermal load and other loadings may be identified as hot spots, shelling, spalling, rolling contact fatigue (RCF), and corrugation. The mechanisms for the formation of such defects are pivoted over the existing thermal environment of dynamic interacting surfaces. This review summarizes the works of early investigations and recent advances in modeling the heat transfer conditions required to estimate the temperature distribution at the contact zone. The heat partitioning method for both drag and stop braking conditions, in the presence of rail chill effect, is emphasized. Thermal gradient, introduced by localized temperature rise in the contact zone, in the presence of variable friction coefficient, promotes the RCF process. These alter the residual stresses in the contact region to cause a structural shakedown, aggravate plastic flow and activates ratchetting phenomenon in rails. The evolution of thermomechanical surface and subsurface fatigue cracks are also discussed for the completeness of this article. The effect of all such defect formation, emerging from thermal loading condition, and their countermeasures for defect mitigation are presented in this review. This abridged technical documentation envisions attracting more research in the area to improve wheel–rail set design and performance standards to extend enhanced safety and comfort to rail transport operation. It is opined that the thermomechanical loading, their effects on promoting defect formation and propagation should be studied in combination instead of the current practice of treating them separately.     

Glass fiber-reinforced epoxy composites

Glass fiber-reinforced epoxy composites were prepared from the matrix resins tetraglycidyl diaminodiphenylmethane

1 Systematic name: N,N,N′,N′-Tetrakis(2,3-epoxypropyl)-4,4′-diaminodiphenylmethane.

(TGDDM) and tetraglycidyl bis(o-toluidino)-methane

2 Systematic name: N,N,N′,N′-Tetrakis(2,3-epoxypropyl)-4,4′-bis(o-toluidino)methane.

(TGMBT) using various amines like 4,4′-diaminodiphenylmethane (DDM), 4,4′-diaminodiphenylsulfone (DDS) and diethylene triamine (DETA) as curing agents. The fabricated laminates were evaluated for their mechanical and dielectrical properties and chemical resistance. The composites prepared using an epoxy fortifier (20 phr) showed significant improvement in the mechanical properties.     

Optical and electrical properties of ZrSe3 single crystals grown by chemical vapour transport technique

Single crystals of the lamellar compound, ZrSe₃, were grown by chemical vapour transport technique using iodine as a transporting agent. The grown crystals were characterized with the help of energy dispersive analysis by X-ray (EDAX), which gave confirmation about the stoichiometry. The optical band gap measurement of as grown crystals was carried out with the help of optical absorption spectra in the range 700–1450 nm. The indirect as well as direct band gap of ZrSe₃ were found to be 1.1 eV and 1.47 eV, respectively. The resistivity of the as grown crystals was measured using van der Pauw method. The Hall parameters of the grown crystals were determined at room temperature from Hall effect measurements. Electrical resistivity measurements were performed on this crystal in the temperature range 303–423 K. The crystals were found to exhibit semiconducting nature in this range. The activation energy and anisotropy measurements were carried out for this crystal. Pressure dependence of electrical resistance was studied using Bridgman opposed anvils set up up to 8 GPa. The semiconducting nature of ZrSe₃ single crystal was inferred from the graph of resistance vs pressure. The results obtained are discussed in detail.     

Adsorption of beta blockers to environmental surfaces

Beta-adrenergic blocking agents (beta blockers) are widely used pharmaceuticals which have been detected in the environment. Predicting the transport and ultimate fate of beta blockers in the environment requires understanding their adsorption to soils and sediments, something for which little information is currently available. The objective of this work was to examine the adsorption of three beta blockers, propranolol, metoprolol and nadolol, to a natural alluvial material, as well as to six minerals present as components of the alluvial material. Batch adsorption experiments indicate that, for most of the minerals studied, compound hydrophobicity is an important predictor of adsorption, with propranolol,the most hydrophobic compound studied, adsorbing to the greatest extent. Results further suggest that, for the minerals studied, electrostatic effects are not a good predictor of adsorption; adsorption extent was not well-predicted by either surface zeta potential or by the difference between experiment pH and point of zero charge, despite the cationic nature af the three beta blockers at experiment pH values. Experiments were conducted to examine the effect of an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), on adsorption. Results indicate that SDBS significantly increases the adsorption of propranolol to two different sorbents. This result is potentially important because surfactants such as SDBS are likely to be present in wastewater effluents with beta blockers and could influence their mobility in the environment.