A simple decision tree-based disturbance monitoring system for VSC-based HVDC transmission link integrating a DFIG wind farm

Fault detection and classification is a key challenge for the protection of High Voltage DC (HVDC) transmission lines. In this paper, the Teager–Kaiser Energy Operator (TKEO) algorithm associated with a decision tree-based fault classi f ier is proposed to detect and classify various DC faults. The Change Identification Filter is applied to the average and differential current components, to detect the first instant of fault occurrence (above threshold) and register a Change Identified Point (CIP). Further, if a CIP is registered for a positive or negative line, only three samples of currents (i.e., CIP and each side of CIP) are sent to the proposed TKEO algorithm, which produces their respective 8 indices through which the, fault can be detected along with its classification. The new approach enables quicker detection allowing utility grids to be restored as soon as possible. This novel approach also reduces computing complexity and the time required to identify faults with classification. The importance and accuracy of the proposed scheme are also thor oughly tested and compared with other methods for various faults on HVDC transmission lines.     

Inverted emulsion polymerization route to polyaniline‐3D nanofiber network using sulfonated‐p‐cresol as novel dopant

Sulfonated‐p‐cresol (SPC) was used as novel dopant for the first time in the synthesis of polyaniline in 3D nanofiber networks (PANI‐3D). Polyaniline in 3D nanofiber network was prepared using organic solvent soluble benzoyl peroxide as oxidizing agent in presence of SPC and sodium lauryl sulfate (SLS) surfactant via inverted emulsion polymerization pathway. The influence of synthesis conditions such as the concentration of the reactants, stirring/static condition, and temperature etc., on the properties and formation of polyaniline nanofiber network were investigated. Polyaniline in 3D nanofiber network with 40–160 nm (diameter), high yield (134 wt % with respect to aniline used), and reasonably good conductivity (0.1 S/cm) was obtained in 24 h time. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Investigation of a Novel Condensation Aerosol Generator: Solute and Solvent Effects

Part I of this article presents results of an experimental study on gas-phase nucleation for three model solutes and their solvent, propylene glycol (PG), with variables being solute concentration and the nature of the solute substance. A single manifestation of an aerosol generator, which forms condensation aerosols by cooling of hot vapor issuing from an electrically heated, pumped capillary, is described and used for all experiments. The effects of solute concentration and solute type were studied for deoxycorticosterone (DOC), benzil (BZ), and phenyl salicylate (PhS). Suppression of homogeneous nucleation and occurrence of heterogeneous condensation of the solvent was observed at different solute concentrations for BZ, PhS, and DOC. The nature and concentration of the solute dissolved in the solvent was shown to determine the final particle size distribution of the condensed aerosol. In the case of the least volatile solute, DOC, solute aerosol and total aerosol size distributions were identical at low solute concentrations. A transitional concentration region then existed in which a bimodal solute aerosol was formed, followed at high concentrations by increasing separation of the solvent-dominated aerosol size distribution and that of the solute. In Part II of this article, the effect of DOC dissolution in different solvents was studied at fixed solute concentration. The effects of six glycol solvents--i.e., PG, ethylene glycol (EG), dipropylene glycol (DPG), diethylene glycol (DEG), triethylene glycol (TEG), and tetraethylene glycol (TetEG)--and three nonglycol solvents--i.e., dimethyl sulfoxide (DMSO), formamide (FORM), and oleyl alcohol (OA)--were studied, as these affected the resultant aerosol sizes. Suppression of total aerosol mass median aerodynamic diameter (MMAD) was observed on dissolution of 0.5% w/w DOC in each solvent, although suppression occurred to different extents. It was shown that the boiling point or volatility of the solvent used to dissolve the less volatile DOC had an effect on the final particle size distribution of the condensed aerosol and whether the aerodynamic size distributions for the solute and the total aerosol were the same or different.     

Structurally Diverse Histone Deacetylase Photoreactive Probes: Design,Synthesis, and Photolabeling Studies in Live Cells and Tissue

Histone deacetylase (HDAC) activity is modulated in vivo by post-translational modifications and formation of multiprotein complexes. Novel chemical tools to study how these factors affect engagement of HDAC isoforms by HDAC inhibitors (HDACi) in cells and tissues are needed. In this study, a synthetic strategy to access chemically diverse photoreactive probes (PRPs) was developed and used to prepare seven novel HDAC PRPs 9 – 15 . The class I HDAC isoform engagement by PRPs was determined in biochemical assays and photolabeling experiments in live SET-2, HepG2, HuH7, and HEK293T cell lines and in mouse liver tissue. Unlike the HDAC protein abundance and biochemical activity against recombinant HDACs, the chemotype of the PRPs and the type of cells were key in defining the engagement of HDAC isoforms in live cells. Our findings suggest that engagement of HDAC isoforms by HDACi in vivo may be substantially modulated in a cell- and tissue-type-dependent manner.     

Temperature–enthalpy curve for energy targeting of distillation columns

The temperature–enthalpy (T–H) diagram of a distillation column at practical near-minimum thermodynamic condition (PNMTC) or the column grand composite curve (CGCC) is a useful representation for energy targeting studies and may be generated from a converged simulation of a base-case column design. The calculation procedure for the CGCC involves determination of the net enthalpy deficit at each stage by generating envelopes from either the condenser end (top-down approach) or the reboiler end (bottom-up approach). However, the values calculated by the two approaches differ for stages with feeds because existing procedures for CGCC generation do not consider the enthalpy balances at the feed stages. In fact, the net enthalpy deficits at feed stages calculated by both approaches are erroneous even for the simplest case of binary distillation. A feed stage correction (FSC) that rigorously considers the mass and enthalpy balance equations at feed stages is proposed in this work to resolve the discrepancy. Instead of assuming that the compositions obtained from the converged simulation for a feed stage will remain unchanged at PNMTC, the pinched compositions for the feed are determined by the intersection of the equilibrium curve and the feed q-line. Rather than perform an additional flash calculation to establish the pinched feed compositions, a quadratic approximation is developed here for column targeting purposes by assuming the relative volatility obtained from the simulation to remain constant in the neighborhood of the feed stage. The proposed FSC ensures that the CGCC is identical whether the calculations are performed by the top-down approach or the bottom-up approach. The effect of the FSC on the targets for energy conservation by reflux modification, feed conditioning, and introduction of side reboilers/condensers is discussed. As the energy target for reflux modification is determined by the CGCC pinch which typically occurs at or close to the feed location, the significance of the FSC on the reflux modification target is highlighted through several case studies including a complex column featuring multiple feeds and consequently multiple pinch points. The CGCCs for these case studies are generated by a computer program based on the FSC and a single analytical equation for the calculation of the net enthalpy deficits that allows every stage to have a feed, liquid product, vapor product, and side exchanger. The studies show that the reflux modification targets may be erroneous in many cases, if the FSC is ignored.     

Experimental study of paddy drying in a vortex chamber

The intensification of interfacial mass, heat, and momentum transfer makes vortex chambers potentially interesting for the efficient drying of paddy, allowing shorter drying times and/or more compact equipment. The presence of a shell introduces particular challenges. Intraparticle diffusion limitations are strong and may reduce the advantage from intensified interfacial mass and heat transfer and the efficiency of air usage. Furthermore, high shear and normal stresses in the fast rotating particle bed may cause damage to the paddy shell, posing problems for transport and storage. With these specific aspects in mind, the use of vortex chambers for paddy drying is experimentally evaluated.     

Particle distribution control in cast aluminium alloy-mica composites

A suspension of mica particles (40m diameter and 3.7 thick) obtained in a mechanically stirred Al-4 wt % Cu-1.5 wt % Mg melt was poured and solidified in a variety of moulds under different heat flow configurations. The resulting cast structure showed a non-uniform distribution of dispersed mica particles with mica-depleted and segregated zones due to their flotation before and during solidification. The experimentally observed profiles of mica-free regions deviate significantly from those computed on the basis of Stokes's law and freezing-time computations. In relatively thick castings, segregation of mica could be minimized by using low pouring temperatures and/or side as well as bottom chilling. It was found, however, that thin castings (12.5 mm) could easily be produced with a homogeneous distribution of mica particles.     

Minimization and identification of conducted emission bearing current in variable speed induction motor drives using PWM inverter

The recent increase in the use of speed control of ac induction motor for variable speed drive using pulse width modulation (PWM) inverter is due to the advent of modern power electronic devices and introduction of microprocessors. There are many advantages of using ac induction motor for speed control applications in process and aerospace industries, but due to fast switching of the modern power electronic devices, the parasitic coupling produces undesirable effects. The undesirable effects include radiated and conducted electromagnetic interference (EMI) which adversely affect nearby computers, electronic/electrical instruments and give rise to the flow of bearing current in the induction motor. Due to the flow of bearing current in the induction motor, electrical discharge machining takes place in the inner race of the bearing which reduces the life of the bearing. In high power converters and inverters, the conducted and radiated emissions become a major concern. In this paper, identification of bearing current due to conducted emission, the measurement of bearing current in a modified induction motor and to minimize the bearing current are discussed. The standard current probe, the standard line impedance stabilization network (LISN)), the electronics interface circuits are used to measure high frequency common mode current, bearing current and to minimize the conducted noise from the system. The LISN will prevent the EMI noise entering the system from the supply source by conductive methods, at the same time prevents the EMI generated if any due to PWM, fast switching in the system, will not be allowed to enter the supply line. For comparing the results with Federal Communications Commission (FCC) and Special Committee on Radio Interference (CISPR) standards, the graphs are plotted with frequency Vs, line voltage in dBμ V, common mode voltage in dBμ V and the bearing current in dBμ A with out and with minimizing circuits.