Gate and drain SEU sensitivity of sub-20-nm FinFET- and Junctionless FinFET-based 6T-SRAM circuits by 3D TCAD simulation

Scaling of metal–oxide–semiconductor field-effect transistors (MOSFETs) to below a few tens of nanometer has failed to make significant improvements. FinFETs were introduced to replace MOS devices in circuits, offering good performance improvement in the nanoscale regime. Memories occupy a major portion of chip area. Their reliability is a primary concern in harsh environments such as cosmic radiation. Also, in the nanoscale regime, reliability proves to be challenging. We present herein FinFET- and junctionless FinFET-based 6T-static random-access memories (SRAMs) for the 16-nm technology node. In the literature so far, either drain or gate strike has been considered. In this work, we studied irradiation in both the drain and the gate region. The FinFET-based 6T-SRAM showed higher hardness to single-event upset (SEU) radiation in both regions compared to junctionless FinFET-based 6T-SRAM.     

An Enhanced MPR OLSR Protocol for Efficient Node Selection Process in Cognitive Radio Based VANET

Wireless Personal Communications - A VANET is an excellent instance of a wireless sensor network. The mobile vehicles are the nodes and communication happens between the vehicular nodes. This...     

Jute and hollow conjugated polyester composites for outdoor & indoor insulation applications

The research work aims at investigating the fitness of jute and hollow conjugated polyester (HCP) composites for indoor and outdoor applications. Limiting oxygen value index, natural weathering exposure was done on four optimized composite structures; i) sandwich structure composite (A); ii) blended non-woven structure composite (B); iii) multiple layers with 5% of low melt polyester added composite (C); (iv) multiple layers of non-woven stitched composite (D) were produced. Their tensile strength, strain at break, and Young’s modulus values were evaluated both before and after the coating of acrylic-based silicon emulsion (ASE). From the experimental results, it is suggested that sample A can be used for an interior trim, sample B can be a base material for interior designing, sample C can replace the usage of wood, plastics, metals, and alloys in hardware applicationsand sample D can be used in interiors as an insulation material in commercial buildings for the purpose of internal cooling or heating.     

Abdominal tuberculosis: a presumptive diagnosis

BACKGROUND: Abdominal tuberculosis (TB) is common. But the diagnosis of abdominal TB is fraught with difficulties as it is often not possible to get a microbiological confirmation of the infection. We therefore undertook this study to highlight those pertinent clinical and laboratory features which would enable one to make a provisional diagnosis of abdominal TB early, to pave way for a trial of anti-tuberculosis chemotherapy. METHOD: This is a retrospective study of 12 patients treated for abdominal TB in our department over a period of 2 years. FINDINGS: Seven of the patients suffered from chronic diarrhoea for periods ranging from 4 weeks to 12 months. Four patients had progressive abdominal distension (ascites). The last patient came in with multiple abdominal swellings. Seven patients had clinical and biochemical features of malabsorption. Another 9 patients also had persistent pyrexia. The ascitic fluid was exudative in the 4 patients mentioned earlier. A definitive diagnosis could not be established in any of these patients. The diagnosis of abdominal TB was thus one of exclusion in these patients who showed prompt response to anti-tuberculosis therapy. CONCLUSION: Our study justifies a trial of anti-TB chemotherapy in TB endemic areas in the following clinical situations: (a) patients with chronic diarrhoea of unknown aetiology and (b) patients with exudative ascitic fluid, after all other possible causes, have been excluded. A prompt response to anti-TB therapy should be accepted as sufficient ground for the diagnosis of abdominal TB even when histopathological or microbiological confirmation of the disease is not possible. Our study reflects the experience of other workers from Third World countries.     

Effects of pyruvate, succinate, and lactate enhancement on beef longissimus raw color

Beef strip loins (n=30) were divided into halves, and each half was assigned randomly to one of four injection enhancements: (1) non-enhanced control, (2) 3% pyruvate, (3) 3% succinate, and (4) 3% lactate. Steaks were cut and packaged in either vacuum, high oxygen (80% O(2)/20% CO(2)), or PVC. Color and lipid oxidation were measured on days 0, 5, and 13 of storage at 1°C. Enhancement had a significant effect on steak pH. On day 13 of storage, steaks enhanced with lactate, pyruvate, and succinate were less discolored (P<0.05) than control steaks in PVC and high oxygen. Enhancement darkened steaks (P<0.05) compared with control steaks. Succinate had the greatest and pyruvate had the least metmyoglobin-reducing activity (P<0.05). Lactate and pyruvate decreased the TBARS values of steaks packaged in PVC (P<0.05) whereas pyruvate was most effective for lowering lipid oxidation in high-oxygen packaging.     

Effects of pyruvate on lipid oxidation and ground beef color

Our overall objective was to better understand the effects of added pyruvate on enhanced beef color stability. The 2 possible mechanisms assessed were the role of pyruvate in lipid oxidation and direct interaction between pyruvate and beef myoglobin. Microsomes were incubated with pyruvate at pH 5.6, 25 °C, and lipid oxidation was measured hourly for 3 h. Bovine oxymyoglobin at pH 5.6 was incubated with pyruvate and used to quantify both redox stability (metmyoglobin formation) and pyruvate-myoglobin adduction using mass spectrometry analysis. Surface color and lipid oxidation were measured on ground beef patties stored for 6 d in polyvinyl chloride over-wrap (PVC) or high oxygen. Addition of pyruvate to microsomes decreased lipid oxidation compared with controls (P < 0.05). Conversely, no effect on myoglobin was observed (no changes in redox stability and no peaks corresponding to pyruvate were observed; P > 0.05). However, pyruvate increased color stability and decreased lipid oxidation of ground beef patties packaged in PVC and high oxygen. Pyruvate decreased nitric oxide metmyoglobin-reducing capacity and oxygen consumption of patties compared with controls (P < 0.05). This research suggests that pyruvate may improve beef color stability primarily through its antioxidant effect on lipids. Practical Application: Discoloration of meat often results in significant revenue loss. This study suggests that pyruvate can improve the color stability of patties packaged in high oxygen and PVC primarily through its antioxidant effect on lipids.     

Yttrium aluminum garnet powders by nitrate decomposition and nitrate–urea solution combustion reactions—a comparative study

Precursors for yttrium aluminum garnet (Y₃Al₅O₁₂—YAG) were synthesized by simple decomposition of concentrated aqueous solution of nitrates and combustion of concentrated aqueous solution of nitrates with urea on a heater. The precursor formed by the former reaction was granules of agglomerated powder while that from the latter reaction was a voluminous and porous sponge-like mass. Both precursors were ground to powders and subjected to detailed thermogravimetric–differential thermal analysis and X-ray diffraction studies. The precursor from the simple decomposition of nitrates exhibited a total loss in weight of about 18% in stages (25 to 300 °C and 300 to 600 °C) accompanied by endotherms—characterized as processes of dehydration of absorbed moisture and decomposition of residual nitrates, respectively. The as formed precursor and that heated to 820 °C were amorphous. Crystallization to YAG phase occurred from an amorphous oxide characterized by an exotherm above 820 °C with no loss of weight. The precursor from nitrate–urea combustion reaction was found to exhibit a weight loss of 2.5% accompanied by a shallow endotherm in the range of 25 to 300 °C—characterized as the process of dehydration of absorbed moisture. No further weight loss or heat effect was noticed, confirming it to be chemically pure YAG. This as formed precursor was found to be crystalline YAG. The difference in chemical composition of the precursors formed by these two reactions is attributed to the difference in the actual reaction temperatures during their formation—lower reaction temperature for the endothermic decomposition of nitrates and higher reaction temperature for the exothermic combustion associated with the formation of a bright flame. The morphology of the precursor powder formed by the former reaction exhibited only cracks while that of the precursor from the latter reaction exhibited pores and voids. The precursor from the former reaction was calcined at 1100 °C to form into chemically pure YAG. Zeta potential variation with pH for the aqueous suspensions of the crystalline YAG powders from both the reactions exhibited a maximum value in the range of 40 to 50 mV around a pH of 4, indicating stability of these dispersions towards coagulation at this pH. Particle size distribution of wet ground powders (slurries with 20%, v/v, solid at a pH of 4) showed that the powder from combustion reaction could be formed into a finer size than that from simple nitrate decomposition, indicating the agglomerates of combustion reaction were softer.     

Synthesis of boron/nitrogen substituted carbons for aqueous asymmetric capacitors

Boron/nitrogen substituted carbons were synthesized by co-pyrolysis of polyborazylene/coal tar pitch blends to yield a carbon with a boron and nitrogen content of 14 at% and 10 at%, respectively. The presence of heteroatoms in these carbons shifted the hydrogen evolution overpotential to −1.4 V vs Ag/AgCl in aqueous electrolytes, providing a large electrochemical potential window (∼2.4 V) as well as a specific capacitance of 0.6 F/m². An asymmetric capacitor was fabricated using the as-prepared low surface area carbon as the negative electrode along with a redox active manganese dioxide as the positive electrode. The energy density of the capacitor exceeded 10 Wh/kg at a power density of 1 kW/kg and had a cycle life greater than 1000 cycles.     

A 2D Transconductance and Sub-threshold behavior model for triple material surrounding gate (TMSG) MOSFETs

A 2D analytical model for transconductance, Sub-threshold current and Sub-threshold swing for Triple Material Surrounding Gate MOSFET (TMSG) is presented in this paper. Based on the solution of two dimensional Poisson equation, the physics based model of sub-threshold current of the device is derived. The model also includes the effect of gate oxide thickness and silicon thickness on the sub-threshold swing characteristics. Transconductance to drain current ratio of the triple material surrounding gate is calculated since it is a better criterion to access the performance of the device. The effectiveness of TMSG design was scrutinized by comparing with other triple material and dual material gate structures. Moreover the effect of technology parameter variations is also studied and proposed. This proposed model offers basic guidance for design of TMSG MOSFETs. The results of the analytical model are compared with the MEDICI simulation results thus providing validity of the proposed model.