Three-parameter vs. two-parameter Weibull distribution for pultruded composite material properties

The three-parameter and two-parameter Weibull distributions are compared using 26 mechanical property data sets of fiber-reinforced polymeric (FRP) composite materials manufactured by the pultrusion process. Both strength and stiffness properties were examined. The probability distributions were compared on the basis of goodness of fit, nominal design values, and allowable load to achieve uniform reliability. It is recommended that the two-parameter Weibull distribution be used to characterize FRP composite material properties. The primary basis for this recommendation is small differences in nominal design values and small differences in allowable loads between the two-parameter and three-parameter Weibull distributions. Other supporting reasons for the recommendation are similar observed significance levels in distribution fitting, computational efficiency, and the fact that the location parameter of the three-parameter Weibull distribution is near the first order statistic.     

Correction to Construction of Panoramic Image Mosaics with Global and Local Alignment

International Journal of Computer Vision -     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Phase Shifter for a 915 MHz Phased Array Hyperthermia System

This paper describes a design for an analog phase shifter operating at 915 MHz and suitable for use in a phased array microwave hyperthermia system. Here, the major operating constraint was minimization of amplitude variation over a 1800 phase shift, whereas previous phase shifters were designed to obtain a linear relationship between phase and control voltage. The result is a simple, inexpensive hybrid coupler phase shifter that operates over a narrow bandwidth and provides 180°of continuous phase shift with input powers up to 1 W.     

Tracing success: graphical methods for analysing successful collaborative problem solving

The aim of this paper is to evaluate the use of trace diagrams for analysing collaborative problem solving. The paper describes a study where trace diagrams were used to analyse joint navigation in a virtual environment. Ten pairs of undergraduates worked together on a distributed virtual task to collect five flowers using two bees with each participant controlling one of the bees. This task is used extensively in research on multi-robot systems. The joint navigation of the pairs was analysed using trace diagrams. They showed that more successful pairs divided the task up, showed very little overlap and very little backtracking. Whereas, the less successful pairs, showed no task division, there was significant overlap and extensive backtracking. From this analysis we developed numerical measures of task division, overlap and backtracking. Task division was significantly and negatively related with task performance. Backtracking and overlap were significantly and positively correlated.     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.     

Application of the FE‐Method to the Simulation of Fatigue Crack Growth in real Structures

In the following paper at first general concepts which have to be considered for the accomplishment of a 3D fatigue crack propagation simulation by the FE‐method in real structures are introduced. In doing so numerical aspects concerning the necessary mesh generation as well as fracture mechanical issues will be discussed. Furthermore the 3D crack simulation program ADAPCRACK3D, which has been developed at the Institute of Applied Mechanics at University of Paderborn, is presented in its general functionality. The simulation example of the crack propagation in a shutter ring of a hydraulic press shows the practical relevance of both the implemented algorithms and fracture mechanical concepts.     

Chemical vapor deposition of amorphous ruthenium-phosphorus alloy films

Chemical vapor deposition growth of amorphous ruthenium-phosphorus films on SiO₂ containing ∼ 15% phosphorus is reported. cis-Ruthenium(II)dihydridotetrakis-(trimethylphosphine), cis-RuH₂(PMe₃)₄ (Me = CH₃) was used at growth temperatures ranging from 525 to 575 K. Both Ru and P are zero-valent. The films are metastable, becoming increasingly more polycrystalline upon annealing to 775 and 975 K. Surface studies illustrate that demethylation is quite efficient near 560 K. Precursor adsorption at 135 K or 210 K and heating reveal the precursor undergoes a complex decomposition process in which the hydride and trimethylphosphine ligands are lost at temperatures as low at 280 K. Phosphorus and its manner of incorporation appear responsible for the amorphous-like character. Molecular dynamics simulations are presented to suggest the local structure in the films and the causes for phosphorus stabilizing the amorphous phase.