Energy Efficiency of an Indirect Thermally Coupled Distillation Sequence

Several thermally coupled distillation sequences have been proposed to improve the thermal inefficiency of conventional distillation sequences. Particularly, for the separation of ternary mixtures, structures that perform a lateral extraction in one of the columns of the integrated arrangement have been shown to provide significant energy savings. The structure of existing sequences, based on conventional distillation columns, might provide the basis for alternate thermally coupled designs. In this paper, it is shown how a thermally coupled system derived from an indirect conventional sequence can provide energy savings through a proper optimization of the interconnecting streams.     

Wetting angles and photocatalytic activities of illuminated TiO2 thin films

TiO₂ thin films have been prepared by physical vapour deposition (PVD) and plasma enhanced chemical vapour deposition (PECVD) to study the UV-induced photo-activity of this material. Wetting angle variations and photo-catalytic activity for the degradation of dyes upon UV illumination have been compared for thin films with different crystalline structure (amorphous, rutile and anatase), microstructure (columnar, compact, etc.) and porosities as estimated from the values of their refraction indices and their direct assessment with a quartz crystal monitor. The surface of the thin films became superhydrophilic upon UV light irradiation and then it recovered its original state by keeping the samples in the dark. Wetting angle decays follow very similar kinetics for amorphous and crystalline films, independently of their actual porosities. By contrast the photo-catalytic activity was very dependent on the crystalline structure of the films (anatase > rutile > amorphous) and on their porosities. The different behaviour depicted by the films with regard to these two properties suggests that they respond to different though related mechanisms and that they cannot be considered as equivalent when trying to prove the photo-activity of TiO₂.     

New investigation of phase equilibria in the system Al-Cu-Si

The phase equilibria and invariant reactions in the system Al-Cu-Si were investigated by a combination of optical microscopy, powder X-ray diffraction (XRD), differential thermal analysis (DTA) and electron probe micro analysis (EPMA). Isothermal phase equilibria were investigated within two isothermal sections. The isothermal section at 500 °C covers the whole ternary composition range and largely confirms the findings of previous phase diagram investigations. The isothermal section at 700 °C describes phase equilibria only in the complex Cu-rich part of the phase diagram. A new ternary compound τ was found in the region between (Al,Cu)-γ₁ and (Cu,Si)-γ and its solubility range was determined. The solubility of Al in κ-CuSi was found to be extremely high at 700 °C. In contrast, no ternary solubility in the β-phase of Cu-Al was found, although this phase is supposed to form a complete solid solution according to previous phase diagram assessments. Two isopleths, at 10 and 40 at.% Si, were investigated by means of DTA and a partial ternary reaction scheme (Scheil diagram) was constructed, based on the current work and the latest findings in the binary systems Al-Cu and Cu-Si. The current study shows that the high temperature equilibria in the Cu-rich corner are still poorly understood and additional studies in this area would be favorable.     

The on-line texture analysis of steel strips

A new on-line texture-analyzing system and its application to nondestructive r value determination is discussed. In addition to providing a brief theoretical background and describing the instrumental set-up, the article presents off-line measurements with this equipment and demonstrates the high accuracy of the determined r-values. A special feature of the unit is the possibility to simultaneously measure the most important r values—r₀, r₄₅, r₉₀, and r_m.     

Transition metal- chalcogen systems XI: the platinum- selenium phase diagram

The platinum-selenium phase diagram was investigated by differential thermal analysis, metallography, and X-ray powder diffraction methods. The two previously known intermediate phases, Pt₅Se₄ and PtSe₂, both melt congruently: Pt₅Se₄ at ∼1070 °C and PtSe₂ (under its own vapor pressure) at 1245 ± 10 °C. Pt₅Se₄ forms a eutectic with Pt at 1065 ± 2 °C and ∼42 at % Se and another one with PtSe₂ at 1067 ± 2 °C and somewhat below 45 at.% Se. On cooling, Pt and PtSe₂ form a metastable eutectic at 1037 ± 2 °C and ∼43 at % Se. Between PtSe₂ and Se, a degenerate eutectic was found at 221 °C, which also indicates negligible solubility of platinum in solid selenium.     

Textured PMN–PT and PMN–PZT

A promising way to improve the performance of piezoelectric ceramics is grain orientation by templated grain growth. In this work lead-based piezoelectric ceramics Pb(Mg_1/3Nb_2/3)_0.68Ti_0.32O₃ (PMN–32PT) and Pb(Mg_1/3Nb_2/3)_0.42(Ti_0.638Zr_0.362)_0.58O₃ (PMN–37PT–21PZ) ceramics were textured via templated grain growth process. For texturization (001)-oriented BaTiO₃ (BT) platelets (approximately 10 μm × 10 μm × 2 μm) were utilized as templates. The texturized ceramics were accomplished by aligning the templates by tape casting. The template growth into the matrix resulted in textured ceramics with Lotgering factors between 0.94 and 0.99 for both compositions. Consequences of the texture are enhanced dielectric and piezoelectric properties. Unipolar strain-field measurements of textured ceramics showed 0.25% strain s ₃₃ at 3 kV/mm. Large signal d ₃₃^* of up to 878 pm/V were determined directly from strain measurements. Compared with randomly oriented ceramics in texturized samples unipolar strain s ₃₃ and large signal d ₃₃^* was enhanced by a factor of up to 1.8.     

Application of advanced materials for ship construction – Experiences and problems

Within the paper a short overview is given regarding the application of advanced materials in the shipbuilding world. The trends for application of high‐strength structural steel, aluminium alloys and composites as well as their limits and restrictions are mentioned. Specific attention is paid to material and corrosion problems observed in shipbuilding and ships in service. As main topics the application of high‐tensile strength structural steel for ship structural members, for ballast water tanks and the involved corrosion problems, the fatigue resistance and “undermatch” situation of welded aluminium alloys compared to steel as well as the corrosion of composites, i.e. osmosis, are mentioned. New developments of ships, e.g. high‐speed crafts and wigs, are pointed out. Conclusions for further research and development in the material field are drawn. The importance of the inter‐relationships amongst the improved material properties, design and calculation aspects as well as the fabrication technologies are stated.     

Laboratory-scale liquefiers for natural gas: A design and assessment study

Exact knowledge of natural gas composition is essential in custody transfer to determine the energy content of the delivery. However, for liquefied natural gas (LNG), a reliable composition determination is difficult. Here, we describe the design of a laboratory-scale reference liquefier that enables the validation and calibration of optical spectroscopy sensors by providing them with a sample of metrologically traceable composition. Hence, it is crucial to avoid fractionation of the sample during liquefaction. This is realized by supercritical liquefaction of a reference gas mixture in conjunction with a special vapor–liquid-equilibrium (VLE) cell. As this is a demanding high-pressure application, low-pressure condensation as liquefaction method was also assessed. Through experimental investigations and VLE calculations, preservation of the composition of the produced liquid sample during condensation was studied. We conclude that under optimized conditions, validation, and calibration measurements of optical sensors can be performed on condensed liquids, which, however, needs further confirmation.     

Influence of the residual stress state of coatings on the wear behavior in external turning of AISI 4140 and Ti–6Al–4V

The residual stress state of coatings influences tool life and performance in machining significantly. Due to thermo-mechanical loads during the cutting process the coatings require tailored properties. Beside the coating structure the two most important properties are the residual stress state and the chemical composition of the coating. Therefore, the influence of these two properties is investigated in this study, comparing the cutting performance in continuous and interrupted cutting of 42CrMo4 (AISI 4140) and Ti–6Al–4V. It is shown that the residual stress states of the coating close to the surface and close to the substrate are important for the wear behavior. High compressive residual stresses near the substrate combined with a material-optimized composition increase the resistance against chipping. Flank wear resistance increases with high compressive residual stresses near the surface and decreasing stresses towards the substrate.