Simplified Impedance Model for Adhesively Bonded Piezo-Impedance Transducers

The electromechanical impedance technique employs surface-bonded lead zirconate titanate piezoelectric ceramic patches as impedance transducers for structural health monitoring and nondestructive evaluation. The patches are bonded to the monitored structures using finitely thick adhesive bond layer, which introduces shear lag effect, thus invariably influencing the electromechanical admittance signatures. This paper presents a new simplified impedance model to incorporate shear lag effect into electromechanical admittance formulations, both one-dimensional and two-dimensional. This provides a closed-form analytical solution of the inverse problem, i.e. to derive the true structural impedance from the measured conductance and susceptance signatures, thus an improvement over the existing models. The influence of various parameters (associated with the bond layer) on admittance signatures is investigated using the proposed model and the results compared with existing models. The results show that the new model, which is far simpler than the existing models, models the shear lag phenomenon reasonably well besides providing direct solution of a complex inverse problem.     

Modelling of a downdraft biomass gasifier with finite rate kinetics in the reduction zone

A model of a downdraft gasifier has been developed based on chemical equilibrium in the pyro‐oxidation zone and finite rate kinetic‐controlled chemical reactions in the reduction zone. The char reactivity factor (C_RF) in the reduction zone, representing the number of active sites on the char and its degree of burn out, has been optimized by comparing the model predictions against the experimental results from the literature. The model predictions agree well with the temperature distribution and exit gas composition obtained from the experiments at C_RF=100. A detailed parametric study has been performed at different equivalence ratios (between 2 and 3.4) and moisture content (in the range of 0–40%) in the fuel to obtain the composition of the producer gas as well as its heating value. It is observed that the heating value of the producer gas increases with the increase in the equivalence ratio and decrease in the biomass moisture content. The effect of divergence angle of the reduction zone geometry (in the range of 30–150°) on the temperature and species concentration distributions in the gasifier has been studied. An optimum divergence angle, giving the best quality of the producer gas, has been identified for a particular height of the reduction zone. Copyright © 2009 John Wiley & Sons, Ltd.     

Robust and minimum norm partial quadratic eigenvalue assignment in vibrating systems: A new optimization approach

The partial quadratic eigenvalue assignment problem (PQEVAP) concerns reassigning a few undesired eigenvalues of a quadratic matrix pencil to suitably chosen locations and keeping the other large number of eigenvalues and eigenvectors unchanged (no spill-over). The problem naturally arises in controlling dangerous vibrations in structures by means of active feedback control design. For practical viability, the design must be robust, which requires that the norms of the feedback matrices and the condition number of the closed-loop eigenvectors are as small as possible. The problem of computing feedback matrices that satisfy the above two practical requirements is known as the Robust Partial Quadratic Eigenvalue Assignment Problem (RPQEVAP). In this paper, we formulate the RPQEVAP as an unconstrained minimization problem with the cost function involving the condition number of the closed-loop eigenvector matrix and two feedback norms. Since only a small number of eigenvalues of the open-loop quadratic pencil are computable using the state-of-the-art matrix computational techniques and/or measurable in a vibration laboratory, it is imperative that the problem is solved using these small number of eigenvalues and the corresponding eigenvectors. To this end, a class of the feedback matrices are obtained in parametric form, parameterized by a single parametric matrix, and the cost function and the required gradient formulas for the optimization problem are developed in terms of the small number of eigenvalues that are reassigned and their corresponding eigenvectors. The problem is solved directly in quadratic setting without transforming it to a standard first-order control problem and most importantly, the significant “no spill-over property” of the closed-loop eigenvalues and eigenvectors is established by means of a mathematical result. These features make the proposed method practically applicable even for very large structures. Results on numerical experiments show that the proposed method considerably reduces both feedback norms and the sensitivity of the closed-loop eigenvalues. A study on robustness of the system responses of the method under small perturbations show that the responses of the perturbed closed-loop system are compatible with perturbations.     

Microfabrication and characterization of metal-embedded thin-film thermomechanical microsensors for applications in hostile manufacturing environments

Effective monitoring and diagnosis of manufacturing processes is of critical importance. If critical manufacturing process conditions are continuously monitored, problems can be detected and solved during the processing cycle. However, current technology still evidently lags behind practical needs. Microfabricated thin-film thermocouples and strain gauges are attractive for their small size and fast response. It is challenging to fabricate and embed these sensors into metallic components that are widely used in manufacturing. This paper investigates the fabrication, embedding, and characterization of metal embedded thin-film thermocouples and strain gauges. The materials (dielectric and metallic) constituting a complete microsensor were characterized and optimized. The results obtained from characterization and optimization of materials are presented and discussed. Thin-film thermocouples on stainless steel substrates (before and after embedding) were calibrated to elevated temperatures. The behavior of thin-film strain gauges was also studied. The metal embedded sensors demonstrated good accuracy, sensitivity, and linearity that matched the performance of commercial thermocouples and strain gauges well. The metal embedded microsensors are promising for in situ monitoring in hostile manufacturing environments.     

Application of the Feynman-Kac path integral method in finding excited states of quantum systems

Group theory considerations and properties of a continuous path are used to define a failure tree procedure for finding eigenvalues of the Schrödinger equation using stochastic methods. The procedure is used to calculate the lowest excited state eigenvalues of eigenfunctions possessing anti-symmetric nodal regions in configuration space using the Feynman-Kac path integral method. Within this method the solution of the imaginary time Schrödinger equation is approximated by random walk simulations on a discrete grid constrained only by symmetry considerations of the Hamiltonian. The required symmetry constraints on random walk simulations are associated with a given irreducible representation and are found by identifying the eigenvalues for the irreducible representation corresponding to symmetric or antisymmetric eigenfunctions for each group operator. The method provides exact eigenvalues of excited states in the limit of infinitesimal step size and infinite time. The numerical method is applied to compute the eigenvalues of the lowest excited states of the hydrogenic atom that transform as Γ² and Γ⁴ irreducible representations. Numerical results are compared with exact analytical results.     

A study of concurrency control in real-time, active databasesystems

Real-time active database systems (RTADBSs) have attracted a considerable amount of research attention in the past and a number of important applications have been identified for such systems, such as telecommunications network management, automated air traffic control, automated financial trading, process control and military command and control systems. In spite of the recognized importance of this area, very little research has been devoted to exploring the dynamics of transaction processing in RTADBSs. Concurrency control (CC) constitutes an integral part of any transaction processing strategy and, thus, deserves special attention. We study CC strategies in RTADBSs and postulate a number of CC algorithms. These algorithms exploit the special needs and features of RTADBSs and are shown to deliver substantially superior performance to conventional real-time CC algorithms     

Characterization of laser and laser/thermal annealed semiconducting iron silicide thin films

-FeSi₂ is an important semiconducting silicide which is being studied extensively. In this paper, we report our results of the effect of laser and laser-thermal annealing on the properties of -FeSi₂. 5N purity Fe was deposited on Si substrate and was subsequently irradiated by CW and pulsed laser separately followed by thermal annealing to reduce the laser induced damage. The samples were then characterized by sheet resistance, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), optical reflectance and absorption studies. Lastly, -FeSi₂/n-Si heterojunctions were fabricated and the effect of laser treatment on the junction ideality factor was investigated. All these characterizations indicated the formation of good quality -FeSi₂, particularly after pulsed laser followed by thermal treatment.     

Scanning electron microscopy and ultrasonic studies of drawn polypropylenes

Ultrasonic measurements and scanning electron microscope studies are reported on a series of drawn samples of polypropylene. The ultrasonic measurements were performed over the frequency range 15 to 35 MHz and over a temperature range 283 to 343K. The scanning electron microscope observations confirmed the predictions from density data that the ‘void’ content initially increases on drawing and then decreases. The acoustic measurements on the samples with the highest draw ratios indicated that severe restriction of the motion of the polymer occurs when the fibrous structure is formed.