Magnetic Resonance Visualisation of Flow and Pore Structure in Packed Beds with Low Aspect Ratio

Different NMR techniques were combined to obtain the structure and velocity information for a systematic investigation of fixed beds with low aspect ratio (tube diameter to particle diamter, d_t/d_p) in the range 1.4 to 32. The structure of the void space was determined for a variety of packed beds of glass beads or regular and irregular porous pellets by magnetic resonance imaging (MRI). Based on the images the radial distribution of the voids within the bed was obtained. Ordering effects were found even for non‐spherical and polydisperse particles, and a maximum of the fluid density near the tube wall was confirmed for all pellet geometries and sizes. By combining MRI with velocity encoding, velocity profiles and distributions of flow velocity components of a single fluid phase through packed beds have been acquired. The radial velocity distribution follows an oscillatory pattern which largely reflects the ordering of the particles, which can be accessed from the density distribution of the interparticle fluid. Maximum velocities of up to four times the average value were found to occur near the tube wall. This wall effect was observed for all but the smallest particles, where the aspect ratio was d_t/d_p = 32. Moreover, a visualisation of flow pattern in the presence of packed particles was achieved by using a tagging technique, and the stationary flow field could be identified for an experimental time of several hours.     

Synthesis of polypropylene‐graft‐maleic anhydride compatibilizer and evaluation of nylon 6/polypropylene blend properties

Polymer blends based on polyolefins are of a great interest owing to their broad spectrum of properties and practical applications. However, because of poor compatibilities of components, most of these systems generally exhibit high interfacial tension, a low degree of dispersion and poor mechanical properties. It is generally accepted that polypropylene (PP) and nylon 6 (N6) are not compatible and that their blending results in poor materials. The compatibility can be improved by the addition of a compatibilizer, and in this study PP was functionalized by maleic anhydride (MAH) in the presence of an optimized amount of dicumyl peroxide (DCP). The reaction was carried out in the molten state using an internal mixer. Then, once the compatibilizer polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) was prepared, it was added at various concentrations (2.5–10 wt%) to 30/70 glass fibre reinforced N6 (GFRN6) PP, and the mechanical properties were evaluated. It was found that the incorporation of the compatibilizer enhanced the tensile properties (tensile strength and modulus) as well as the Izod impact properties of the notched samples. This was attributed to better interfacial adhesion as evidenced by scanning electron microscopy (SEM). The optimum in these properties was achieved at a critical PP‐g‐MAH concentration. Copyright © 2005 Society of Chemical Industry     

Fuzzy control of nitrogen removal in predenitrification process using ORP.

In order to meet increasingly stringent discharge standards, new applications and control strategies for the sustainable removal of nitrogen from wastewater have to be implemented. In the past years, numerous studies have been carried out dealing with the application of fuzzy logic to improve the control of the activated sludge process. In this paper, fuzzy control strategies of predenitrification systems are presented that could lead to better effluent quality and, in parallel, to a reduction of chemicals consumption. Extensive experimental investigations on lab scale plant studies have shown that there was excellent correlation between nitrate concentration and ORP value at the end of the anoxic zone. Results indicated that ORP could be used as an on-line fuzzy control parameter of nitrate recirculation and external carbon addition. The optimal value of ORP to control nitrate recirculation and external carbon addition was - 86 +/- 2 mV and - 90 +/- 2 mV, respectively. The results obtained with real wastewater also showed the good performance and stability of the fuzzy controllers independently from external disturbances. The integrated control structure of nitrate recirculation and external carbon addition in the predenitrification system is also presented.     

Nitrogen management in reservoir catchments through constructed wetland systems.

In this study, nitrogen removal was investigated in pilot-scale subsurface flow (SSF) and in free water surface flow (FWS) constructed wetlands installed in the campus of TUBITAK-Marmara Research Center, Gebze, near Istanbul, Turkey. The main purposes of this study are to apply constructed wetlands for the protection of water reservoirs and to reuse wastewater. Experiments were carried out at continuous flow reactors. The effects of the type of plants on the removal were investigated by using emergent (Canna, Cyperus, Typhia spp., Phragmites spp., Juncus, Poaceae, Paspalum and Iris.), submerged (Elodea, Egeria) and floating (Pistia, Salvina and Lemna) marsh plants at different conditions. During the study period HLRs were 30, 50, 70, 80 and 120 L m(2)d(-1) respectively. The average annual NH4-N, NO(3)-N, organic N and TN treatment efficiencies in SSF and FWS wetlands are 81% and 68%, 37% and 49%, 75% and 68%, 47% and 53%, respectively. Nitrification, denitrification and ammonification rate constant (k20) values in SSF and FNS systems have been found as 0.898 d(-1) and 0.541 d(-1), 0.488 d(-1) and 0.502 d(-1), 0.986 d(-1) and 0.908 respectively. Two types of the models (first-order plug flow and multiple regression) were tried to estimate the system performances.     

Surface topography of planar PMMA grating structures produced by the UV-laser based phase mask method

Surface relief gratings are written into the surface of a planar PMMA substrate by the UV-excimer laser based phase mask method. The surface relief grating topography (grating amplitude and grating constant) is investigated in dependence on the laser irradiation parameters (fluence and irradiation dose) yielding some information relevant for the ablation and grating formation mechanism.     

Ergonomic job design in frequent manual lifting tasks: A microcomputer-based model

The main objective of this paper is to generate ergonomic software that can be used in the design and evaluation of manual materials handling tasks so as to minimize the risk of injury. Specifically, this study is aimed at developing a microcomputer-based model for the design of frequent manual lifting tasks based ont he concept of job saverity index. The microcomputer-based software package is intended to be used by non-experts in the field of MMH. Possible engineering and administrative controls are implemented in the software in case if human lifting abilities are exceeded. The software was written in AutoLISP for the IBM personal computer. The knowledge base of the software is built upon a set of two models which were developed in the present study. The models were based on 2,736 observations.     

Economical technology for cryoproduct storage and delivery

Translated from Khimicheskoe i Neftyanoe Mashinostroenie, No. 11, pp. 22–23, November, 1992.