Influence of drying and extraction methods on yield and chemical composition of the essential oil of Satureja hortensis

The aerial parts of Satureja hortensis, cultivated in Iran (Research Station of Alborz, Karaj), were collected at the full-flowering stage and dried by three different drying methods (sun-drying, shade-drying and oven-drying at 45 °C). The essential oils of every treatment were obtained by hydro-distillation of the aerial parts. In addition, the essential oil of shade-dried sample was obtained by two other distillation methods (water- and steam-distillation and direct steam-distillation). The oils were analyzed by capillary GC and GC–MS. Statistical analysis showed no significant difference between oil yield (w/w) of the oven-dried sample (1.06%) compared to shade-dried (0.94%) and sun-dried (0.87%). The oil content of the shade-dried sample, obtained by hydro-distillation, was higher (0.94%) than that of the steam-distilled (0.27%). Twenty-three components were identified in the oil of S. hortensis in the different drying methods, including carvacrol (46.0–48.1%) and γ-terpinene (37.7–39.4%) as main components. Seventeen compounds were characterized in the oils of different distillation methods, including carvacrol (12.3–46%) and γ-terpinene (37.7–70.4%). Although the drying methods had no significant effect on oil composition of S. hortensis, the distillation changed the percentage of main components sharply (significant at 1%). The steam-distillation method produced the lowest amount of carvacrol and highest amount of γ-terpinene. The results showed that extraction by hydro-distillation gave the best results for S. hortensis, based on oil yield and carvacrol percentage.     

Modeling of CO2-brine interfacial tension: Application to enhanced oil recovery

Development of reliable and accurate models to estimate carbon dioxide–brine interfacial tension (IFT) is necessary, since its experimental measurement is time-consuming and requires expensive experimental apparatus as well as complicated interpretation procedure. In the current study, feed forward artificial neural network is used for estimation of CO₂–brine IFT based on data from published literature which consists of a number of carbon dioxide–brine interfacial tension data covering broad ranges of temperature, total salinity, mole fractions of impure components and pressure. Trial-and-error method is utilized to optimize the artificial neural network topology in order to enhance its capability of generalization. The results showed that there is good agreement between experimental values and modeling results. Comparison of the empirical correlations with the proposed model suggests that the current model can predict the CO₂–brine IFT more accurately and robustly.     

Synthesis of Ferrocene-Based Hyperbranched Polyether and Its Catalytic Performance for Thermal Decomposition of Ammonium Perchlorate

A series of ferrocene-based hyperbranched polyethers (HBPE-Fc) with different ferrocene content were synthesized by esterification of ferrocenecarbonyl chloride and hyperbranched polyether (HBPE). ¹H NMR and FT-IR were used to confirm the structure of HBPE and HBPE-Fc. GPC was used to calculate the molecular weights. The catalytic performance of the synthesized HBPE-Fc for thermal decomposition of ammonium perchlorate (AP) was investigated by TG and DTG techniques. The results showed that HBPE-Fc exhibited good catalytic activity on the thermal decomposition of AP. The influence factors on catalytic performances, such as substitution degree of ferrocene and mass ratio of AP/HBPE-Fc were discussed as well.     

Probabilistic Fatigue Life Prediction and Structural Reliability Evaluation of Turbine Rotors Integrating an Automated Ultrasonic Inspection System

The paper presents a general method and procedure for fatigue reliability assessment integrating automated ultrasonic non-destructive inspections. The basic structure of an automated ultrasonic inspection system is presented. Fatigue reliability assessment methodology is developed using uncertainty quantification models for detection, sizing, and fatigue model parameters. The probability of detection model is based on a classical log-linear model coupling the actual flaw size with the ultrasonic inspection reported size. Using probabilistic modeling, the distribution of the actual flaw size is derived. Reliability assessment procedure using ultrasonic inspection data is suggested. A steam turbine rotor example with realistic ultrasonic inspection data is presented to demonstrate the overall method. Calculations and interpretations of assessment results based on risk recommendations for industrial applications are given.     

Spatial analyses of wildlife contact networks

Datasets from which wildlife contact networks of epidemiological importance can be inferred are becoming increasingly common. A largely unexplored facet of these data is finding evidence of spatial constraints on who has contact with whom, despite theoretical epidemiologists having long realized spatial constraints can play a critical role in infectious disease dynamics. A graph dissimilarity measure is proposed to quantify how close an observed contact network is to being purely spatial whereby its edges are completely determined by the spatial arrangement of its nodes. Statistical techniques are also used to fit a series of mechanistic models for contact rates between individuals to the binary edge data representing presence or absence of observed contact. These are the basis for a second measure that quantifies the extent to which contacts are being mediated by distance. We apply these methods to a set of 128 contact networks of field voles (Microtus agrestis) inferred from mark–recapture data collected over 7 years and from four sites. Large fluctuations in vole abundance allow us to demonstrate that the networks become increasingly similar to spatial proximity graphs as vole density increases. The average number of contacts, , was (i) positively correlated with vole density across the range of observed densities and (ii) for two of the four sites a saturating function of density. The implications for pathogen persistence in wildlife may be that persistence is relatively unaffected by fluctuations in host density because at low density is low but hosts move more freely, and at high density is high but transmission is hampered by local build-up of infected or recovered animals.     

The Electrochemical Behavior of Au/AuNPs/PNA/ZnSe-QD/ACA Electrode Towards CySH Oxidation

Nano-Micro Letters - This work describes the electrochemical behavior of azodicarboxamide (ACA) film immobilized on the surface of penicillamine (PNA)/ZnSe-quantum dot (ZnSe-QD) gold nanoparticle...     

The potential for greenhouse gases mitigation in household sector of Iran: cases of price reform/efficiency improvement and scenario for 2000–2010

Iran's demographic profile is sharply youth oriented and this upcoming generation's needs for employment and housing, coupled with low-energy efficiency vectors and consumption patterns, has created a constant rise in energy demand and greenhouse gas (GHGs) emissions in the residential sector. Improved energy efficiency as a national policy lynchpin for demand reduction and GHGs mitigation, has become commonplace. OPEC countries however, Iran included, suffer an obvious lack of consumer incentive because of low fuel prices. This study evaluates the twin impacts of price reform and efficiency programs on energy carriers’ consumption and GHGs mitigation in the Iranian housing sector. For this purpose, the demand functions for energy carriers, has been developed by econometrics process models.     

Hot tensile properties and microstructural evolution of as cast NiTi and NiTiCu shape memory alloys

Hot tensile properties of as cast NiTi and NiTiCu shape memory alloys were investigated by hot tensile test at temperature range of 700–1100 °C using the strain rate of 0.1 s⁻¹. The NiTi alloy exhibited a maximum hot ductility at temperature range of 750–1000 °C, while the NiTiCu alloy showed it at temperature range of 800–1000 °C. It was found that at temperatures less than 750 °C, diffusion-assisted deformation mechanism was inactive leading to semi-brittle type of failure and limited ductility in both alloys. Also it was found that at temperature range of 800–1000 °C, dynamic recrystallization is dominant leading to high ductility. Likewise, the fracture surface of the specimens presenting the maximum hot ductility showed an ideal type of ductile rupture in which they gradually pulled out to a fine point. On the other hand, the decline in ductility occurred at the temperatures above 1000 °C was attributed to the liquid phase formation leading to interdendritic and intergranular type of fracture.     

pH-dependant structural and morphology evolution of Ni(OH)2 nanostructures and their morphology retention upon thermal annealing to NiO

Nickel hydroxide nanosheets, nanobelts and nanorods were prepared by hydrothermal treatment of the precipitates obtained at different pH values. The morphology and crystal structure of the products could be controlled simply by adjusting the pH value at precipitation. Interconnected nanosheets of hexagonal β-Ni(OH)₂ with thickness around 10–20 nm were formed at pH ∼ 11, whereas nanobelts with typical widths around 40–80 nm, and nanorods with diameters around 50–60 nm of phase pure α-Ni(OH)₂ containing intercalated sulphate ions were obtained in the pH range ∼9.5–8.5. Thermal annealing of the hydroxides at 500 °C yielded cubic phase NiO with morphologies similar to their hydroxide precursors. X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and energy dispersive X-ray (EDX) analysis were used to characterize the as-prepared products. The role of pH in controlling the phase and morphology of the products was discussed.