Investigation of structure and mechanical properties of toughened poly(l‐lactide)/thermoplastic poly(ester urethane) blends

In this study, poly(l ‐lactide) (PLA) is melt‐blended with thermoplastic polyurethane (TPU) to modify the brittleness of PLA. An aliphatic ester‐based TPU was selected in order to have an ester sensitivity for degradation and an inherent biocompatibility. Using this compatible TPU, there was no need to apply problematic compatibilizers, so the main positive properties of PLA such as biocompatibility and degradability were not challenged. The detected microstructure of PLA/TPU blends showed that when the TPU content was lower than 25 wt %, the structure appeared as sea‐islands, but when the TPU content was increased, the morphology was converted to a cocontinuous microstructure. A higher interfacial surface area in the blend with 25 wt % TPU (PLA25) resulted in a higher toughness and abrasion resistance. The various analyses confirmed interactions and successful coupling of two phases and confirmed that melt‐blending of PLA with the aliphatic ester‐based TPU is a convenient, cost‐effective, and efficient method to conquer the brittleness of PLA. The prepared blends are general‐purpose plastics, but PLA25 showed an optimum mechanical strength, toughness, and biocompatibility suitable for a wide range of applications. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43104.     

Experimental investigation of the governing parameters in the electrospinning of poly(3‐hydroxybutyrate) scaffolds: Structural characteristics of the pores

We sought to determine the impact of electrospinning parameters on a trustworthy criterion that could evidently improve the maximum applicability of fibrous scaffolds for tissue regeneration. We used an image analysis technique to elucidate the web permeability index (WPI) by modeling the formation of electrospun scaffolds. Poly(3‐hydroxybutyrate) (P3HB) scaffolds were fabricated according to predetermined conditions of levels in a Taguchi orthogonal design. The material parameters were the polymer concentration, conductivity, and volatility of the solution. The processing parameters were the applied voltage and nozzle‐to‐collector distance. With a law to monitor the WPI values when the polymer concentration or the applied voltage was increased, the pore interconnectivity was decreased. The quality of the jet instability altered the pore numbers, areas, and other structural characteristics, all of which determined the scaffold porosity and aperture interconnectivity. An initial drastic increase was observed in the WPI values because of the chain entanglement phenomenon above a 6 wt % P3HB content. Although the solution mixture significantly (p < 0.05) changed the scaffold architectural characteristics as a function of the solution viscosity and surface tension, it had a minor impact on the WPI values. The solution mixture gained the third place of significance, and the distance was approved as the least important factor. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Optimizing the mechanical and physical properties of thermoplastic starch via tuning the molecular microstructure through co‐plasticization by sorbitol and glycerol

Nowadays, environmental hazards caused by plastic wastes are a major concern in academia and industry. Utilization of biodegradable polymers derived from renewable sources for replacing common petroleum‐based plastics is a potential solution for reducing the problem. In this regard, starch has become one of the most promising alternatives to non‐biodegradable polymers for depleting plastic waste thanks to its low expense, abundance, renewability and biodegradability. However, the main drawbacks of starch are its poor processability, weak mechanical properties and severe hydrophilicity. In this work, thermoplastic starch (TPS) samples have been prepared using glycerol and sorbitol as co‐plasticizers in a laboratory co‐rotating twin screw extruder. Based on the mechanical test results, glycerol caused higher elongation to break but had lower tensile strength and elastic modulus compared to sorbitol plasticized starch. Fourier transform infrared spectroscopy and DSC results indicated that the hydrogen bond interaction between starch chains and plasticizers could be improved by replacing glycerol by sorbitol, which resulted in higher resistance against retrogradation proved by XRD results. TGA illustrated that the higher the sorbitol to glycerol ratio was, the more stable was the TPS. Using a proper amount of plasticizers (42 wt% total plasticizer, sorbitol to glycerol ratio 2:1) led to the preparation of a TPS sample with optimized properties including enhanced mechanical properties, high thermal stability, strong hydrogen bond formation and high resistance against retrogradation. © 2017 Society of Chemical Industry     

Adoption and use of e-commerce in SMEs

In this study, nonlinear Logit and probit models are used to analyse the important factors that impact on the tendency of small- and medium-sized enterprises (SMEs) to use electronic commerce in one of the industrial parks in Kermanshah province of Iran. Furthermore, it identifies the major barriers of e-commerce adoption in these SMEs. The Sample of the study includes 35 SMEs in this province. The results of probit and Logit models suggest that a lower level of the internet service costs, motivates firms to adopt e-commerce. In addition, if the government provides free e-commerce facilities for SMEs, it can encourage SMEs to adopt e-commerce. Furthermore, the results show that due to uncertainty in the e-commerce, producing high-quality products and traditional exports cannot raise the tendency of sample firms to adopt e-commerce.     

Physical mechanisms of heat transfer during single bubble nucleate boiling of FC-72 under saturation conditions. II: Theoretical analysis

This paper is the second part of a two-part study concerning the dynamics of heat transfer during the nucleation process of FC-72 liquid. The experimental findings on the nature of different heat transfer mechanisms involved in the nucleation process were discussed in part I. In this paper, the experimental results are compared with the existing boiling models. The boiling models based on dominance of a single mechanism of heat transfer did not match the experimental results. However, the Rohsenow model was found to closely predict the heat transfer through the microconvection mechanism that is primarily active outside the bubble/surface contact area. An existing transient conduction model was modified to predict the surface heat transfer during the rewetting process (i.e. transient conduction mechanism). This model takes into account the gradual rewetting of the surface during the transient conduction process rather than a simple sudden surface coverage assumption commonly used in the boiling literature. The initial superheat energy of the microlayer (i.e. microlayer sensible energy) was accurately calculated and found to significantly contribute in microlayer evaporation. This even exceeded the direct wall heat transfer to microlayer at high surface superheat temperatures. A composite model was introduced that closely matches our experimental results. It incorporates models for three mechanisms of heat transfer including microlayer evaporation, transient conduction, microconvection, as well as their influence area and activation time. The significance of this development is that, for the first time, all submodels of the composite correlation were independently verified using experimental results.     

Heat Capacity of Defective Semiconducting Carbon Nanotubes

Using a random tight-binding model within the coherent potential approximation, the effects of boron and nitrogen doping on the temperature dependence of the specific heat of semiconducting zigzag carbon nanotubes are studied. It is shown that the electronic specific heat capacity behaves anomalously when the temperature is lowered. The presence of this anomaly is clarified on the basis of the idea of the so-called Schottky anomaly. More importantly, in the presence of dopants, the position of this anomaly moves towards higher temperatures and its height shifts down as the dopant concentration is increased. Such behavior is attributed to the substantial modifications in the density of states.     

Black Nickel Coating and Color Anodized Layers for Solar Absorber

Solar selective absorbers are considered as an essential part of a thermal solar collector for which the optical properties are dependent upon their structure and surface morphology. In this paper, optical properties of Ni-pigmented anodized are compared with black electroless nickel coatings. The effect of heat treatment on optical properties of the coatings was also investigated. Anodized films were formed in 6 M phosphoric acid followed by a black coloration process. Scanning electron microscope was used to study the morphology, and X-ray diffraction was employed to identify the phases present. Evaluation of optical properties was carried out by spectral reflectance. Evaluation of the optical characteristics showed that Ni-pigmented anodized and black electroless samples, after heat treatment, had the highest absorption coefficient at about 0.98 as well as the lowest emission coefficient. The ξ factor reached about 6 in heat treated Ni-pigmented anodized layer and offered optimal properties in this research.     

Cryptanalysis of an iterated halving-based hash function: CRUSH

Iterated Halving has been suggested as a replacement to the Merkle?Damga?rd (MD) construction in 2004 anticipating the attacks on the MDx family of hash functions. The CRUSH hash function provides a specific instantiation of the block cipher for Iterated Halving. The authors identify structural problems with the scheme and show that they can trivially identify collisions and second preimages on many equal-length messages of length ten blocks or more. The cost is ten decryptions of the block cipher, this being less than the generation of a single digest. In addition, these attacks can be used to differentiate CRUSH from a random oracle in O(1). The authors show that the complexity of finding a preimage in the unpadded CRUSH with the length encoding is negligible and extend this attack on CRUSH with the length encoding in cost O(2/sup 32/). This attack is a multi-preimage attack, since the attacker can produce a large number of messages for a given message digest for the cost of O(2/sup 32/). Hence, this attack can be used as a multi-collision and a multisecond- preimage as well. They show that if the attacker knows the last 64-bits of the message digest in advance, he can do the time-consuming part of the attack off-line. The authors show that even if Iterated Halving is repaired, the construction has practical issues that means it is not suitable for general deployment.     

SPARCL: an effective and efficient algorithm for mining arbitrary shape-based clusters

Clustering is one of the fundamental data mining tasks. Many different clustering paradigms have been developed over the years, which include partitional, hierarchical, mixture model based, density-based, spectral, subspace, and so on. The focus of this paper is on full-dimensional, arbitrary shaped clusters. Existing methods for this problem suffer either in terms of the memory or time complexity (quadratic or even cubic). This shortcoming has restricted these algorithms to datasets of moderate sizes. In this paper we propose SPARCL, a simple and scalable algorithm for finding clusters with arbitrary shapes and sizes, and it has linear space and time complexity. SPARCL consists of two stages—the first stage runs a carefully initialized version of the Kmeans algorithm to generate many small seed clusters. The second stage iteratively merges the generated clusters to obtain the final shape-based clusters. Experiments were conducted on a variety of datasets to highlight the effectiveness, efficiency, and scalability of our approach. On the large datasets SPARCL is an order of magnitude faster than the best existing approaches.