Optimal charge rates for a lithium ion cell

The optimum charge rate for a lithium ion cell at each cycle is determined to maximize the useful life of the cell without using optimization algorithms. In previous work, we showed that by applying a dynamic optimization routine the number of cycles can be increased by approximately 29.4% with respect to the case with one optimal charge current [7]. The dynamic optimization results indicated that the optimum charge rates are the minimum currents at which the constraints for the useful life are satisfied. This is due to the minimum charge rate resulting in minimum side reaction rate and capacity fade. Useful cell life is defined as the number of cycles before the end of discharge voltage (EODV) drops below 3.0 V or the cell discharge capacity becomes less than 20% of the original discharge capacity. The new approach presented in this work is able to find the optimal charge rates in a few minutes while the previous optimization algorithm takes at least one day, and improves the useful cell life by approximately 41.6% with respect to using only one optimal charge current.     

Improving the quality of surface in the polishing process with the magnetic abrasive powder polishing using a high-frequency induction heating source on CNC table

In this research, polishing flat surfaces has been done by using a completely new and innovative method. In this method, rotary magnetic tool that carry magnetic abrasive powders, is placed in a very strong thermal induction field, and magnetic rotary tool frequently change its direction from clockwise (CW) to counterclockwise (CCW) and CCW to CW. The frequency of changing rotation direction is an important parameter of this innovation method. The intended pieces for polishing operations have been placed on a synchronic two-axis Cartesian CNC table, and the gap between rotary magnetic tool and the sheet surface can be controlled by a power transmission screw operating in the direction of the vertical axis. Several experiments have proved high performance of the new proposed method in the process of polishing.     

Decoupled adaptive neuro-fuzzy (DANF) sliding mode control system for a Lorenz chaotic problem

This paper introduces a decoupled adaptive neuro-fuzzy (DANF) sliding mode control system for the chaos control problem in a system without precise system model information. It has on-line learning ability to deal with the parametric uncertainty and disturbance by adjusting the control parameters and no constrained conditions and prior knowledge of the controlled plant is required in the design process. Also, a decoupled adaptive sliding mode controller is developed to control the chaotic Lorenz system for comparison. Finally, the effectiveness of the proposed decoupled adaptive sliding mode and DANF sliding mode controllers are demonstrated by some simulated results.     

The Ablation and Oxidation Behaviors of SiC Coatings on Graphite Prepared by Slurry Sintering and Pack Cementation

SiC coatings were generated on graphite using slurry sintering (SS) and pack cementation (PC). The samples’ ablation features were assessed by an oxyacetylene torch. The rates of mass ablation of the PC–SiC and SS–SiC coatings were approximated 2.17?×?10^?3 and 9.52?×?10^?3 g s^?1, respectively, decreased by 84.1 and 29.6% compared to the uncoated samples. It was mainly attributed to the formation of a SiO₂ layer on the surface. The continuous SiO₂ molten film formed via the PC–SiC oxidation generates a sealing mechanism which can be an obstacle against the oxygen diffusion and hinder more ablation. This is while discontinuous SiO₂ film formed from the thin SS–SiC cannot protect the graphite effectively. The non-isothermal oxidation test shows that without the SiC coating, the sample weight is lost largely from 25 to 1500 °C, and its weight loss was 2.2% after the TGA. However, after coating, the samples possessed excellent oxidation protection and weight losses of SS–SiC and PC–SiC coatings are down to 1.3 and 0.6%, respectively. The more oxidation of the graphite substrate occurred due to the formation of macrocracks in the coating during the TGA and also the formation of holes on SiO₂ glass layer owing to release of CO or CO₂.     

Changes in Effective Thermal Conductivity During the Carbothermic Reduction of Magnetite Using Graphite

Knowledge of the effective thermal diffusivity changes of systems undergoing reactions where heat transfer plays an important role in the reaction kinetics is essential for process understanding and control. Carbothermic reduction process of magnetite containing composites is a typical example of such systems. The reduction process in this case is highly endothermic and hence, the overall rate of the reaction is greatly influenced by the heat transfer through composite compact. Using Laser-Flash method, the change of effective thermal diffusivity of magnetite-graphite composite pellet was monitored in the dynamic mode over a pre-defined thermal cycle (heating at the rate of 7 K/min to 1423 K (1150 °C), holding the sample for 270 minutes at this temperature and then cooling it down to the room temperature at the same rate as heating). These measurements were supplemented by Thermogravimetric Analysis under comparable experimental conditions as well as quenching tests of the samples in order to combine the impact of various factors such as sample dilatations and changes in apparent density on the progress of the reaction. The present results show that monitoring thermal diffusivity changes during the course of reduction would be a very useful tool in a total understanding of the underlying physicochemical phenomena. At the end, effort is made to estimate the apparent thermal conductivity values based on the measured thermal diffusivity and dilatations.     

Pipe damper,Part I: Experimental and analytical study

In this paper the behavior of steel pipes, filled and unfilled with concrete, is studied under cyclic shear to examine the possibility of their use as a seismic damper. Two specimens of steel pipes filled inside with concrete are tested under monotonic and cyclic shear. Four other specimens of bare steel pipes are tested under fully reversed cyclic shear loading. The results show that the bare steel pipes are capable of absorbing a great amount of energy under a severe cyclic shear loading with a stable hysteretic behavior. This behavior is also simulated using the finite element method. Then, parametric studies are performed to investigate the effects of variations in geometrical properties of the pipe on its hysteretic behavior. A simplified bi-linear model is proposed to approximate the hysteretic behavior of the steel pipe as a metallic-yielding damper.     

Degradation of drag reducing polymers in aqueous solutions

The performance of drag reducing polymers in turbulent flow is restricted by their mechanical degradation. This study examines how the working fluid can affect the degradation behavior of diluted drag reducing polymeric solutions. Solutions having different proportions of tap water and de-ionized water served as the working fluids. Three commercially available water soluble polymeric agents, namely, an anionic copolymer of polyacrylamide, xanthan gum, and polyethylene oxide, were then added to these solutions. All experiments had identical flow rates corresponding to turbulent conditions in a laboratory scale pipe line. Variation of pressure drop in the pipe line was then measured for 2 hours. It was found that polymer degradation is accelerated in tap water solutions compared to that in de-ionized water solutions. However, this is dependent on the specification of the polymer used, namely, the molecular weight of the polymer and the rigidity of its molecular backbone. Furthermore, a new mathematical relation has been developed to investigate degradation of the polymers over time.     

Uncertainty treatment in forced response calculation of mistuned bladed disk

Mistuning, imperfections in cyclical symmetry of bladed disks is an inevitable and perilous occurrence due to many factors including manufacturing tolerances and in-service wear and tear. It can cause some unpredictable phenomena such as mode splitting, mode localization and dramatic difference in forced vibration response. In this paper first, a method is presented which calculates the forced vibration response of a mistuned system based on an exact relationship between tuned and mistuned systems. Then, the genetic algorithm is used for solving an optimization problem to find the worst-case response of bladed-disk assembly. The second part tries to find methods to reduce the system worst-case response. Intentional mistuning which breaks the nominal symmetry of a tuned bladed disk and rearranging the bladed-disk assembly are introduced and used to reduce the system worst-case response. Finally, a two degree of freedom per blade simplified model with 56 blades is used to demonstrate the capabilities of the techniques in reducing the worst response of the bladed-disk system.