Low-concentration ammonia gas sensing using polyaniline nanofiber thin film grown by rapid polymerization technique

Journal of Materials Science: Materials in Electronics - A thin film of polyaniline (PANI) nanofiber was synthesized by a simple and inexpensive rapid chemical polymerization technique on glass...     

Toward secure software-defined networks against distributed denial of service attack

The Journal of Supercomputing - The newly emerged software-defined networking (SDN) paradigm provides a flexible network management by decoupling the network control logic from the data plane,...     

Elastomeric ablative nanocomposites used in hyperthermal environments

Pristine multiwalled carbon nanotubes (MWCNTs) along with the silane coupling agent were incorporated into ethylene propylene diene monomer (EPDM) rubber using dispersion kneader and two roller mixing mill to fabricate ablative nanocomposites used in hyperthermal environment encountered by space vehicle or rocket motor. The 1 wt% addition of MWCNTS in the rubber matrix has remarkably reduced the backface temperature elevation up to 40°C during the ablation testing of the ablatives. The linear and mass ablation resistances have been diminished up to 125% and 74%, respectively, while insulation indexes at 110°C backface temperature of the composite specimens have been elevated up to 51% with increasing the MWCNTS incorporation into the EPDM matrix. Thermal stability and heat absorbance capability of the polymer composites were progressed with increasing the filler to matrix ratio. Thermal conductivity/impedance of the ablatives have been conducted according to the ASTM E1225‐99 and D5470‐03, respectively to execute the effect of MWCNTs concentration on the thermal transport characteristics of the tested specimens. Tensile strength of the composite specimen was augmented up to 42% with increasing nanotubes to polymer ratio. Evenly dispersed MWCNTs in the polymer matrix, polymer pyrolysis, and voids formation in the ablated samples can be scrutinized in the scanning electron microscopy images. POLYM. ENG. SCI., 54:255–263, 2014. © 2013 Society of Plastics Engineers     

Effect of electron‐beam irradiation on ethylene–methyl acrylate copolymer

Ethylene–methyl acrylate copolymer (Elvaloy 1330) was irradiated by an electron beam at different levels of radiation both in the presence and absence of a trimethylolpropane trimethacrylate sensitizer at various dosages of incorporation. The mechanical, thermal, and electrical properties of these samples were compared. The mechanical properties were observed to reach an optimum maximum around 6 Mrad of irradiation and 1 phr of sensitizer incorporation. Furthermore, an increase in either the radiation dose or the sensitizer level helped very little to further modify the properties. The thermal properties as determined by the thermogravimetric analysis and differential scanning calorimetry studies were quite supportive of the observation made during the study of the mechanical properties. The thermal stability of the irradiated samples underwent an increase with increasing electron‐beam dosage. In a manner similar to those of the mechanical properties, the increase in thermal stability was found to reach a maximum at a particular level of treatment and sensitizer incorporation, beyond which there was marginal or no effect at all. The α transition temperature underwent a substantial increase with increasing crosslink density, as evidenced by the increase in gel content with increasing proportion of electron‐beam radiation dose. The other glass‐transition temperature, however, appeared to remain unaffected. The electrical properties, as described by the dielectric constant, volume resistivity, and breakdown voltage, appeared to be affected very little by the electron‐beam radiation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Investigation of Magnetocaloric Behavior of Nanocrystalline Nd0.67A0.33MnO3, (A = Ca,Sr, Ba and Pb)

Colossal magnetoresistive (CMR) materials with the compositional formula, Nd_0.67A_0.33MnO₃ (where A = Ca, Sr, Ba, and Pb) in the nanocrystalline form were prepared by the PVA gel technique. After characterizing the samples structurally, a systematic investigation of magnetization has been undertaken, over a temperature range 10–300 K at 0.05 T magnetic field. An effort has been made to calculate the magnetocaloric behavior of all the samples theoretically using the experimental magnetization data. Other important parameters such as maximum entropy change, full width at half-maximum, relative cooling power, and maximum adiabatic temperature change under 0.05 T were also computed. The observed behavior has been explained qualitatively.     

Electromagnetic interference shielding effectiveness of ethylene vinyl acetate based conductive composites containing carbon fillers

Conductive polymeric based composites were derived from ethylene vinyl acetate rubber filled with Vulcan XC‐72, short carbon fiber (SCF), and their blends. The electromagnetic interference (EMI) shielding effectiveness (SE), return loss, and reflection coefficient were studied. The measurements of the SE of the composites were carried out in two different frequency ranges of 100–2000 MHz and 8–12 GHz (X band). It was observed that the SE of the composites was frequency dependent and it increased with increasing frequency. The increasing of filler loading also enhanced the SE of the composites. The 100% SCF filled composites showed a higher SE compared to that of the filler blend or purely carbon black filled composites. The correlation between the SE and bulk conductivity of various composites was also discussed. The compromise between EMI SE, electrical conductivity, and mechanical properties was obtained when the composites contained both types of filler like particulate carbon black and SCF. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1601–1608, 2001     

Effect of thermal treatment on structure and properties of polyester tire cords

Polyester and nylon are the mostly used reinforcing textile fibers in many industrial rubber applications. Now‐a‐days body ply of a passenger car radial is mostly made up of polyester fiber. Because of its thermoplastic nature, it undergoes some kind of thermal shrinkage during processing and vulcanization, which lead to many problems related to shape, dimension, and dimensional stability. To avoid this, polyester is subjected to thermal treatment at higher temperature. Hence, thermomechanical properties of polyester tire cords become very important. During the thermal treatment, there is not only change in shrinkage, shrinkage force, and mechanical properties but also it affects structural and morphological properties. In this work, the changes in thermomechanical properties due to heat setting have been correlated to structural and morphological changes like crystallinity, crystal size, orientation, crystal perfection, etc. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Microwave‐initiated synthesis of polyacrylamide grafted sodium alginate: Synthesis and characterization

Microwave‐initiated synthesis of polyacrylamide‐grafted sodium alginate, a graft copolymer with wide variety of applications has been reported in this study. The effect of reaction parameters (i.e., irradiation time and monomer concentration) onto the percentage grafting has been investigated. The resulting polymer has been characterized by a variety of characterization techniques such as intrinsic viscosity measurement, Fourier transform infrared spectra, ¹³C NMR spectra, elemental analysis, thermogravimetric analysis, molecular weight determination using static light scattering analysis, and scanning electron micrographs. Further, the flocculation efficiency of this graft copolymer has been investigated in coal suspension. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010