Development of abrasive cut-off wheel having side grooves

The abrasive cut-off wheel fails prematurely during the routine sectioning of workpiece, which may cause injury to the operator. One of the major reasons of premature failure is the improper mixing of the abrasive mixture. In order to provide strength to the wheel, it was reinforced by woven roving type glass fiber and the abrasive mixture was ball milled. Cutting zone temperature becomes high during the cutting operation, which may cause thermal damage to the workpiece and debonding of abrasive from the wheel. It is very difficult to supply the cutting fluid to the cutting zone in order to reduce the temperature. New types of abrasive cut-off wheels were developed, which have radial passages on their surfaces to supply the cutting fluid to the cutting zone. Performance of the wheels was compared and the mechanical strength of the wheel material was tested.     

Use of cellular confinement for improved railway performance on soft subgrades

Due to extensive right-of-way, railroads are inevitably subject to poor subgrade conditions and interrupted service for significant maintenance due to excessive deformations and loss of track geometry. Geocell confinement presents itself as a possible solution for improving performance of ballasted railroad embankments over weak subgrade. To investigate the efficacy of geocell confinement on ballasted railway embankments, a set of well-instrumented, large-scale cyclic plate loading tests and numerical simulations were performed on geocell-confined ballast overlaying a weak subgrade material. The agreement of results from tests and simulations served as a basis for simulating practical track geometry and performance for various geocell configurations and subgrades using three-dimensional (3D) finite element (FE) analyses. The study showed that geocell reinforcement significantly decreased track settlement, decreased subgrade deformations with lower and uniform distribution of vertical stresses on subgrade and inhibited lateral deformation and serviceability under cyclic loading. These results demonstrate that geocell confinement can be an effective alternative to subsurface improvement or shorter maintenance cycles, particularly on weak subgrades.     

Instrumental characterization of clay by XRF,XRD and FTIR

Instrumental characterizations of the clay were performed by different techniques such as XRF, XRD and FTIR. XRF shows the chemical compositions of the clay where Al-oxide and silica oxide are present in major quantity whereas XRD confirms the presence of these minerals in clay. FTIR studies show the presence of quartz, alumina, haematite and different mineral matters.     

Comparison of osteoconductivity and absorbability of beta-tricalcium phosphate and hydroxyapatite in clinical scenario of opening wedge high tibial osteotomy

The purpose of this study was to compare the osteoconductivity, and absorbability of hydroxyapatite or beta-tricalcium phosphate in clinical scenario of opening wedge high tibial osteotomy Total 41 knees of 40 patients with follow up period of more than 1 year were enrolled. These patients were divided into two groups, Group I (22 knees, 21 patients) used hydroxyapatite and Group II (19 knees, 19 patients) used beta-tricalcium phosphate as a substitute in the opening gap. According to proven method, the osteoconductivity was assessed radiographically by the extent of new bone formation at osteotomy space and absorbability was evaluated by measuring the area occupied by substitute at immediate postoperative, postoperative 6 months and 1 year. Regarding preoperative demographic data, no significant differences were found between two groups. No statistically significant differences were found between two groups regarding lower limb alignment (mechanical femorotibial angle, weight-bearing line%) and posterior tibial slope at postoperative and final follow up radiographs. Concerning the osteoconductivity, there were no significant differences between two groups in any zone. However, the absorption rate was significantly greater in the Group II than in Group I at 6 months (Group I: 13.7?±?6.8, group II: 35.3?±?15.8, P?=?0.001) and 1 year (Group I: 24.2?±?6.3, Group II: 49.6?±?14.3, P?<?0.0001). The complications related to bone substitutes were not observed. Both hydroxyapatite and beta-tricalcium phosphate showed satisfactory gap healing without complications and can be successfully used as alternative healing materials in opening wedge high tibial osteotomy. Our study showed that beta-tricalcium phosphate has superior absorbability than hydroxyapatite. But osteoconductivity showed no significant difference.     

Ductile fracture in thin sheet metals: a FEM study of the Sandia fracture challenge problem based on the Gurson–Tvergaard–Needleman fracture model

In this paper, the Gurson–Tvergaard–Needleman (GTN) fracture model has been implemented in a 3D nonlinear finite element framework to investigate ductile failure. The simulation consists of both model parameter calibrations and predictions based on the experimental configurations that were described in the Sandia fracture challenge in 2012. The goal is to test the robustness of the GTN model in predicting crack initiation and propagation in a ductile structural stainless steel (15-5 PH). It has been observed that the predicted load drops at crack initiation agree well with the experimental data. Both the simulation and experiments reveal that cracks always initiate in the subsurface. The observed crack path in the experiments, however, is not unique and is strongly influenced by the geometric variations in the specimen introduced in the fabrication process. The crack path is quite sensitive to the relative location of pre-existing features (notch and holes) in this challenge problem, and a very small variation can potentially lead to different path, hence affecting the ductile failure pattern significantly. Variations in the crack path are also observed in the simulation with different choices of GTN model parameters that control the void nucleation and growth behavior.     

Verification of the applicability of lattice model to concrete fracture by AE study

Notched three-point bend specimens (TPB) were tested under crack mouth opening displacement (CMOD) control at a rate of 0.0004 mm/s and the entire fracture process was simulated using a regular triangular two-dimensional lattice network only over the expected fracture process zone width. The rest of the beam specimen was discretised by a coarse triangular finite element mesh. The discrete grain structure of the concrete was generated assuming the grains to be spherical. The load versus CMOD plots thus simulated agreed reasonably well with the experimental results. Moreover, acoustic emission (AE) hits were recorded during the test and compared with the number of fractured lattice elements. It was found that the cumulative AE hits correlated well with the cumulative fractured lattice elements at all load levels thus providing a useful means for predicting when the micro-cracks form during the fracturing process, both in the pre-peak and in the post-peak regimes.     

The structure and analysis of nanotechnology co-author and citation networks

Research activities and collaborations in nanoscale science and engineering have major implications for advancing technological frontiers in many fields including medicine, electronics, energy, and communication. The National Nanotechnology Initiative (NNI) promotes efforts to cultivate effective research and collaborations among nano scientists and engineers to accelerate the advancement of nanotechnology and its commercialization. As of August 2008, there have been over 800 products considered to benefit from nanotechnology directly or indirectly. However, today’s accomplishments in nanotechnology cannot be transformed into commercial products without productive collaborations among experts from disparate research areas such as chemistry, physics, math, biology, engineering, manufacturing, environmental sciences, and social sciences. To study the patterns of collaboration, we build and analyze the collaboration network of scientists and engineers who conduct research in nanotechnology. We study the structure of information flow through citation network of papers authored by nano area scientists. We believe that the study of nano area co-author and paper citation networks improve our understanding of patterns and trends of the current research efforts in this field. We construct these networks based on the publication data collected for years ranging 1993 through 2008 from the scientific literature database “Web of Science”. We explore those networks to find out whether they follow power-law degree distributions and/or if they have a signature of hierarchy. We investigate the small-world characteristics and the existence of possible community structures in those networks. We estimate the statistical properties of the networks and interpret their significance with respect to the nano field.     

Effects of Clinorotation on Growth and Chlorophyll Content of Rice Seeds

Microgravity, as a different environment, has been shown to affect plant growth and development (Sievers et al. 1996; Sack 1997). In the present study, effects of slow clinorotation (2 rpm) on growth and chlorophyll content in rice (variety: PRH-10) seedlings were investigated. Rice seeds were clinorotated continuously for 3, 5 and 7 days under ambient conditions. Root and shoot lengths and weights of rice seedlings were measured on the third, fifth and seventh day. Chlorophyll was extracted using N, N-Dimethylformamide (DMF). Absorption and fluorescence spectra of chlorophyll were recorded. Chlorophyll a, chlorophyll b and total chlorophyll contents were calculated from absorption spectra using Arnon’s method. Results showed an increase in root and shoot lengths in clinorotated samples. Similar results were obtained for root and shoot weights. Absorption spectra of chlorophyll showed no shift in the absorption peaks. Chlorophyll content was increased in clinorotated samples as compared to the controls. Interestingly, the difference between chlorophyll content in control and clinorotated samples decreased as the number of days of clinorotation increased. Chlorophyll a/b ratio was lowered in clinorotated samples as compared to the controls. These results suggest that slow clinorotation (2 rpm) affects plant growth and chlorophyll content in rice seedlings.     

Modeling and Experimental Studies on 3D-Magnetic Flux Leakage Testing for Enhanced Flaw Detection in Carbon Steel Plates

ABSTRACT

For enhanced detection of flaws in engineering components using magnetic flux leakage (MFL) technique, measurement of the leakage magnetic field components along the three perpendicular directions is beneficial. This article presents the three dimensional-magnetic flux leakage (3D-MFL) modeling and experimental studies carried out on carbon steel plates. Magnetic dipole model has been used for the prediction of MFL signals and images. Sensitivity of the MFL signals peak amplitudes of tangential (H_X), circumferential (H_Y), and normal (H_Z) components with respect to flaw length, width, depth and lift-off have been studied. A 3D-GMR sensor has been used for simultaneous measurement of all the three components of leakage magnetic fields from surface flaws in 12 mm thick carbon steel plates. The experimental MFL images have been compared with the model predicted MFL images. The sensor has shown the capability to detect and image 0.9 mm deep surface flaws with a signal to noise ratio of 8 dB. Principal component analysis (PCA)-based image fusion has been performed for fusion of the 3D-MFL images to obtain a geometrical profile of the flaws. Study reveals that 3D-GMR enhances the capability for detection of flaws having irregular geometries.