纳米Ir／SPE电极的制备及其影响因素

首次选用镍作为中间催化剂,采用吸附还原成长法制备纳米Ir/SPE电极,并就镀浴温度和pH值、H2IrCl6浓度、NaBH4与H2IrCl6配比对电极制备的影响作了深入研究。研究表明:采用吸附还原成长法,以Ni作为中间催化剂,浓度为22mmol·L-1NaBH4与浓度为6mmol·L-1H2IrCl6的混合液作为镀浴,亦即NaBH4与H2IrCl6配比为3.6,pH值为8,镀浴温度为40℃,镀浴时间为24h的条件下,循环镀覆3次,可获得致密、均匀,具有良好电解性能的纳米级Ir/SPE电极。     

HSi80-3硅黄铜船用舵盖铸件精铸工艺的凝固模拟

运用Procast软件对HSi80-3硅黄铜船用舵盖零件在两种浇注工艺方案下的凝固过程进行模拟计算,在此基础上分析探讨了该铸件可能产生缩孔或缩松的部位。模拟显示第一种浇注工艺会在零件主体部位产生严重缩孔,而第二种浇注工艺则能自下而上顺序凝固,避免缩孔或缩松的产生,据此确定了第二种铸造工艺方案,并采用试验进行验证。结果表明,此浇注工艺没有产生技术要求缺陷,证明了凝固模拟的可行性。     

Effect of low-cycle fatigue on the hot ductility of plain carbon steel

In a continuous casting steelmaking operation, the surface of a slab is under a condition that can be characterized as high-temperature, low-cycle fatigue in which the tensile and compressive stress is repeatedly developed. For this reason, for the evaluation of the hot ductility of a slab, considering the fatigue deformation is more feasible before a tensile or compressive test. In this study, the effects of low-cycle fatigue on the hot ductility of steels with a carbon content of 0.06–0.8 wt.% are investigated at various temperatures. For a carbon content of 0.06%, there were no significant differences between the RA values from a simple tensile test and those from a tensile test after fatigue deformation. The tendency of ductility deterioration with fatigue deformation is evident in 0.1 %C steel, and is due to the deformation-induced ferrite film that forms around the prior austenite grain. Conversely, high carbon steel containing 0.8 %C did not show a recovery of hot ductility in a low temperature region, and the specimen on which the tensile was measured after fatigue showed a higher hot ductility in the low temperature region, which is thought to result from the pearlite refinement effects. As the results obtained in this work showed noticeable differences in the hot ductility of carbon steel through the test conditions, it is suggested that for more accurate data, fatigue deformation be adopted in which the temperature range in an unbending operation is determined in the steelmaking factory.     

Microstructure and mechanical property of irradiated Zr−2.5Nb pressure tube in Wolsong unit-1

With the aim of assessing the degradation of Zr−2.5Nb pressure tubes operating in the Wolsong unit-1 nuclear power plant, characterization tests are being conducted on irradiated Zr−2.5Nb tubes removed after 10-year operation. The examined tube had been exposed to temperatures ranging from 264 to 306°C and a neutron fluence of 8.9×10²¹ n/cm² (E>1 MeV) at the maximum. Tensile tests were carried out at temperatures ranging from RT to 300°C. The density of a-type and c-type dislocations was examined on the irradiated Zr-2.5Nb tube using a transmission electron microscope. Neutron irradiation up to 8.9×10²¹ n/cm² (E>1 MeV) yielded an increase in a-type dislocation density of the Zr−2.5Nb pressure tube to 7.5×10¹⁴ m⁻², which was highest at the inlet of the tube exposed to the low temperature of 275°C. In contranst, the c-component dislocation density did not change with irradiation, keeping an initial dislocation density of 0.8×10¹⁴ m⁻² over the whole length of the tube. As expected, the neutron irradiation increased mechanical strength by about 17–26% in the transverse direction and by 34–39% in the longitudinal direction compared to that of the unirradiated tube at 300°C. The change in the mechanical properties with irradiation is discussed in association with the microstructural change as a function of temperature and neutron fluence.     

A note on the optimal pricing and production decisions with price‐driven substitution

Recently, Kim and Bell ( 2011 ) developed a revenue managemnent pricing model with price‐driven substitution. The authors considered production decisions under unlimited production capacity and investigated the impact of price‐driven substitution on a firm's pricing and production decisions. The authors modeled the consumer demands for each market segment as linear additive demand function based on exogenous variables, where demand substitution occurred as a function of price differences between the two products. In this article, we extend this work to examine the impact of a production capacity constraint on the firm's joint pricing and inventory decisions. Based on this extended model, we investigate the impact of price‐driven substitution on a firm's pricing and production decisions where there is a limit on total capacity. We show how revenue managers should adjust prices and production levels to take into account price‐driven substitution under a capacity constraint setting. Both deterministic and stochastic models are developed, and the impact of price‐driven substitution and a capacity constraint on the optimal prices, production levels, and revenues is illustrated.     

A timing controller embedded driver IC with 3.24‐Gbps eDP interface for chip‐on‐glass TFT‐LCD applications

This paper presents a timing controller embedded driver (TED) IC with 3.24‐Gbps embedded display port (eDP), which is implemented using a 45‐nm high‐voltage CMOS process for the chip‐on‐glass (COG) TFT‐LCD applications. The proposed TED‐IC employs the input offset calibration scheme, the zero‐adjustable equalizer, and the phase locked loop‐based bang‐bang clock and data recovery to enhance the maximum data rate. Also, the proposed TED‐IC provides efficient power management by supporting advanced link power management feature of eDP standard v1.4. Additionally, the smart charge sharing is proposed to reduce the dynamic power consumption of output buffers. Measured result demonstrates the maximum data rate of 3.24 Gbps from a 1.1 V supply voltage with a 7.9‐inch QXGA 60‐Hz COG‐LCD prototype panel and 44% power saving from the display system.     

Usability Principles for Augmented Reality Applications in a Smartphone Environment

Through the rapid spread of smartphones, users have access to many types of applications similar to those on desktop computer systems. Smartphone applications using augmented reality (AR) technology make use of users' location information. As AR applications will require new evaluation methods, improved usability and user convenience should be developed. The purpose of the current study is to develop usability principles for the development and evaluation of smartphone applications using AR technology. We develop usability principles for smartphone AR applications by analyzing existing research about heuristic evaluation methods, design principles for AR systems, guidelines for handheld mobile device interfaces, and usability principles for the tangible user interface. We conducted a heuristic evaluation for three popularly used smartphone AR applications to identify usability problems. We suggested new design guidelines to solve the identified problems. Then, we developed an improved AR application prototype of an Android-based smartphone, which later was conducted a usability testing to validate the effects of usability principles.