Extraction of penicillin G from simulated media by an emulsion liquid membrane process

The extraction of penicillin G from simulated media was performed by water/oil/water (w/o/w) emulsion liquid membranes (ELMs) and studied under various operational conditions in a batch system. The degree of extraction achieved was between 80% and 95% under specific conditions. A concentration of greater than nine times the initial concentration of penicillin G in the external phase was obtained in the internal phase. The pH of the internal aqueous solution, containing a basic salt, was theoretically calculated on the basis of the amount of penicillin G transported into the internal phase. The calculated results agreed with the experimental data well and were used to select a suitable type and concentration of a basic salt in the internal phase to give a pH within the range 5 to 8 where penicillin G was stable after the termination of extraction. The extraction of penicillin G was successfully performed by the ELM process with sodium carbonate in the internal phase.     

Monolithic SiGe Up‐/Down‐Conversion Mixers with Active Baluns

The purpose of this paper is to describe the implementation of monolithically matching circuits, interface circuits, and RF core circuits to the same substrate. We designed and fabricated on‐chip 1 to 6 GHz up‐conversion and 1 to 8 GHz down‐conversion mixers using a 0.8 µm SiGe hetero‐junction bipolar transistor (HBT) process technology. To fabricate a SiGe HBT, we used a reduced pressure chemical vapor deposition (RPCVD) system to grow a base epitaxial layer, and we adopted local oxidation of silicon (LOCOS) isolation to separate the device terminals. An up‐conversion mixer was implemented on‐chip using an intermediate frequency (IF) matching circuit, local oscillator (LO)/radio frequency (RF) wideband matching circuits, LO/IF input balun circuits, and an RF output balun circuit. The measured results of the fabricated up‐conversion mixer show a positive power conversion gain from 1 to 6 GHz and a bandwidth of about 4.5 GHz. Also, the down‐conversion mixer was implemented on‐chip using LO/RF wideband matching circuits, LO/RF input balun circuits, and an IF output balun circuit. The measured results of the fabricated down‐conversion mixer show a positive power conversion gain from 1 to 8 GHz and a bandwidth of about 4.5 GHz.     

Shortest path algorithms: A computational study with the C programming language

The main purpose of this study is to evaluate the computational efficiency of algorithms for calculating shortest paths when they are correctly coded by using the C programming language. The eight algorithms that we selected for this experiment are the most efficient, either measured in terms of worst-case bounds or marked as such from previous computational studies; they include the redistributive heap algorithm. We suggest computer implementations that use the full power of C. In particular, the network representation and the various data structures used to keep the scan eligible list may be managed by using only additions and no multiplications, while it is not possible with FORTRAN. These capabilities, unique to C, yield several interesting conclusions: one may expect to speed up a shortest path algorithm by a factor of 20%; in some cases, this factor may reach 30%. Interestingly, the level of programming difficulty required to achieve these benefits is not greater than that required by implementations using arrays.     

Effect of the Liquid-Phase Characteristic on the Microstructures and Dielectric Properties of Donor- (Niobium) and Acceptor- (Magnesium) Doped Barium Titanate

Changes in the microstructure and dielectric properties with the variation of the donor/acceptor ratio in BaTiO₃ ceramics were investigated. In donor-rich specimens, a liquid that appeared during sintering did not penetrate into grain boundaries. However, in the acceptor-rich specimens, the grains were separated by a liquid film during sintering. The much higher mobility of the liquid film than that of the grain boundaries was suggested to cause extensive grain growth in acceptor-rich BaTiO₃. The macroscopic homogenization of dopants because of grain growth in acceptor-rich specimens resulted in changes in the dielectric properties.     

共面转换液晶显示器中获得对比度高于1:600的新技术

薄膜晶体管液晶电视(TFT-LCD TV)因为具有薄、轻、紧凑和可随意放置的特点，已经占据了大部分电视机市场。除了这些物理特性以外，最重要的特性是已具有了良好像质的对比度。为了将对比度提高到1：600以上，对偏振片膜、背光源板、滤色片树脂、电极锥角和摩擦条件等都进行了研究。优化的背光板组合，光滑的电极锥角和摩擦方法的控制是提高对比度的主要控制因素。应用新开发的滤色片树脂，对获得高对比度最为有效。     

Efficient particle filter-based processing algorithm for clutter suppression and IR point targets enhancement

A novel soft decision-based median subtraction filter is presented for clutter suppression and infrared (IR) point targets enhancement. The decision is made based on a jump Markov model and its state and parameter estimation using a particle filter. The scheme is compared with other conventional clutter background removal techniques and good results are obtained.     

Application of artificial neural networks to the analysis of two‐dimensional fluorescence spectra in recombinant E coli fermentation processes

A two‐dimensional (2D) spectrofluorometer was used to monitor various fermentation processes with recombinant E coli for the production of 5‐aminolevulinic acid (ALA). The whole fluorescence spectral data obtained during a process were analyzed using artificial neural networks, ie self‐organizing map (SOM) and feedforward backpropagation neural network (BPNN). The SOM‐based classification of the whole spectral data has made it possible to qualitatively associate some process parameters with the normalized weights and variances, and to select some useful combinations of excitation and emission wavelengths. Based on the classified fluorescence spectra a supervised BPNN algorithm was used to predict some of the process parameters. It was also shown that the BPNN models could elucidate some sections of the process's performance, eg forecasting the process's performance. Copyright © 2005 Society of Chemical Industry     

An online technique for monitoring the insulation condition of AC machine stator windings

A novel online technique for monitoring the insulation condition of ac machine stator windings is proposed in this paper. The concept is to measure the differential leakage currents of each phase winding from the terminal box in a noninvasive manner to assess the insulation condition during motor operation. The conventional differential CTs used for phase fault protection can be replaced with high performance current sensors to measure the leakage current with higher accuracy. Indicators for insulation condition such as the capacitance and dissipation factor are calculated based on the measurements to provide a low cost solution for online insulation condition assessment. A simplified online insulation system model is derived for analysis and interpretation of the measured data. Experimental results on a 15-hp induction motor under simulated insulation degradation conditions show that the proposed technique is a very sensitive method capable of detecting incipient signs of insulation degradation.