Recycling of silicone rubber waste: Effect of ground silicone rubber vulcanizate powder on the properties of silicone rubber

The silicone rubber vulcanizate powder (SVP) obtained from silicone rubber by mechanical grinding exists in a highly aggregated state. The particle size distribution of SVP is broad, ranging from 2 µm to 110 µm with an average particle size of 33 µm. X‐ray Photoelectron Spectroscopy (XPS) and Infrared (IR) Spectroscopy studies show that there is no chemical change on the rubber surface following mechanical grinding of the heat‐aged (200°C/10 days) silicone rubber vulcanizate. Addition of SVP in silicone rubber increases the Mooney viscosity, Mooney scorch time, shear viscosity and activation energy for viscous flow. Measurement of curing characteristics reveals that incorporation of SVP into the virgin silicone rubber causes an increase in minimum torque, but marginal decrease in maximum torque and rate constant of curing. However, the activation energy of curing shows an increasing trend with increasing loading of SVP. Expectedly, incorporation of SVP does not alter the glass‐rubber transition and cold crystallization temperatures of silicone rubber, as observed in the dynamic mechanical spectra. It is further observed that on incorporation of even a high loading of SVP (i.e., 60 phr), the tensile and tear strength of the silicone rubber are decreased by only about 20%, and modulus dropped by 15%, while the hardness, tension set and hysteresis loss undergo marginal changes and compression stress‐relaxation is not significantly changed. Atomic Force Microscopy studies reveal that incorporation of SVP into silicone rubber does not cause significant changes in the surface morphology.     

Preparation and properties of styrene–butadiene rubber based nanocomposites: The influence of the structural and processing parameters

Rubber‐based nanocomposites were prepared with octadecyl amine modified sodium montmorillonite clay and styrene–butadiene rubber with different styrene contents (15, 23, and 40%). The solvent used to prepare the nanocomposites, the cure conditions, and the cure system were also varied to determine their effect on the properties of the nanocomposites. All the composites were characterized with X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies revealed exfoliation for the modified clay–rubber composites. The TEM photomicrographs showed a uniform distribution of the modified clay in the rubber matrix. The thickness of the particles in the exfoliated composites was around 10–15 nm. Although the FTIR study of the unmodified and modified clays showed extra peaks due to the intercalation of the amine chains into the gallery, the spectra for the rubber–clay nanocomposites were almost the same because of the presence of a very small amount of clay in the rubber matrix. All the modified clay–rubber nanocomposites displayed improved mechanical strength. The styrene content of the rubber had a pronounced effect on the properties of the nanocomposites. With increasing styrene content, the improvement in the properties was greater. Dicumyl peroxide and sulfur cure systems displayed similar strength, but higher elongation and slightly lower modulus values were obtained with the sulfur cure system. The curing of the samples at four different durations at 160°C showed that the cure time affected the properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 698–709, 2004     

Melt‐processable rubber: Chlorinated waste tire rubber‐filled polyvinyl chloride

Chlorinated ground rubber tire (Cl‐GRT) particles were used as filler in a plasticized polyvinylchloride (PVC) to develop a melt‐processable rubber composition. Physical properties of the Cl‐GRT‐filled PVC compound showed improvement compared to the nonchlorinated counterpart. Interaction between Cl‐GRT and PVC was examined on the basis of results of stress relaxation, dynamic mechanical thermal analysis, and solvent swelling studies. The Cl‐GRT could be loaded upto 40 parts per hundred parts of PVC, and the composition still retains the elastomeric characteristics. The Cl‐GRT‐filled composite was found to be reprocessable like the unfilled PVC compound. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 622–631, 2002; DOI 10.1002/app.10352     

Throughput analysis in censoring-based cooperative cognitive radio network with energy harvesting

An energy harvesting (EH) and cooperative cognitive radio (CR) network (CRN) is studied in this paper where CR users transmit data through a primary user (PU) channel if the channel remains idle, else an optimal number CRs helps in transmission of PU. To achieve the optimum number of CRs (ONCR) involved in cooperation, a novel scheme based on a combination of channel censoring and total error is proposed. The performance of the proposed scheme is investigated under RF harvesting scenario. The EH is dependent on sensing decision and a CR source harvests energy from PU's RF signal. The harvested energy (HE) is split into two parts: One part is used by the CR network (CRN) for its own transmission, and the other part is used for supporting PU. The effect of the energy allocation factor on total throughput is also investigated. New expressions for optimal number of CRs and throughput are developed. The effect of network parameters such as sensing time, censoring threshold, and energy allocation parameter (EAP) on throughput is investigated. Impact of distance between nodes is also studied.     

Speech enhancement using Teager energy operated ERB-like perceptual wavelet packet decomposition

In recent past, wavelet packet (WP) based speech enhancement techniques have been gaining popularity due to their inherent nature of noise minimization. WP based techniques appeared as more robust and efficient than short-time Fourier transform based methods. In the present work, a speech enhancement method using Teager energy operated equal rectangular bandwidth (ERB)-like WP decomposition has been proposed. Twenty four sub-band perceptual wavelet packet decomposition (PWPD) structure is implemented according to the auditory ERB scale. ERB scale based decomposition structure is used because the central frequency of the ERB scale distribution is similar to the frequency response of the human cochlea. Teager energy operator is applied to estimate the threshold value for the PWPD coefficients. Lastly, Wiener filtering is applied to remove the low frequency noise before final reconstruction stage. The proposed method has been applied to evaluate the Hindi sentences database, corrupted with six noise conditions. The proposed method’s performance is analysed with respect to several speech quality parameters and output signal to noise ratio levels. Performance indicates that the proposed technique outperforms some traditional speech enhancement algorithms at all SNR levels.     

33.7 MHz heavy-ion radio frequency quadrupole linac at VECC Kolkata

A 33.7 MHz heavy-ion radio frequency quadrupole (RFQ) linear accelerator has been designed, built, and tested. It is a four-rod-type RFQ designed for acceleration of 1.38 keVu, qA> or =116 ions to about 29 keVu. Transmission efficiencies of about 85% and 80% have been measured for the unanalyzed and analyzed beams, respectively, of oxygen ((16)O(2+), (16)O(3+), (16)O(4+)), nitrogen ((14)N(3+), (14)N(4+)), and argon ((40)Ar(4+)). The system design and measurements along with results of beam acceleration test will be presented.     

Microscopic studies on the mechanisms of wear of NR,SBR and HNBR vulcanizates under different conditions

Microscopic investigations, undertaken to understand the mechanism of wear of natural rubber (NR), styrene-butadiene rubber (SBR) and hydrogenated nitrile rubber (HNBR) vulcanizates abraded against hard rock, a knurled aluminium disc and a silicone carbide abrader under different conditions, are reported. The wear of NR and SBR vulcanizates against hard rock at low normal load (6 kPa) takes place by a fatigue wear mechanism and it switches over to frictional wear at high normal load (above 18 kPa). In HNBR vulcanizates the wear takes place by an abrasive wear mechanism. Ridges are observed on worn surface of swollen N R and SBR vulcanizates at low normal load, but at higher normal load the wear takes place by catastrophic fracture and extensive plough marks along the direction of abrasion are observed. The wear of NR and SBR vulcanizates proceeds by frictional wear, even at elevated temperatures. In HNBR vulcanizates, the mechanism changes from abrasive wear at 25C to frictional wear above 50C. Above 50C, ridges are observed and the spacing between adjacent ridges increases with rise of temperature.     

Learning rules of a card game from video

This paper presents a framework for automatically learning rules of a simple game of cards using data from a vision system observing the game being played. Incremental learning of object and protocol models from video, for use by an artificial cognitive agent, is presented. iLearn??a novel algorithm for inducing univariate decision trees for symbolic datasets is introduced. iLearn builds the decision tree in an incremental way allowing automatic learning of rules of the game.