Biochemical oxidation of caprolactam-containing wastewater from the production of synthetic fibres

Conclusions The chemical mutagenesis method is recommended for use in local purification installations for cleaning up of caprolactam-containing wastewater.Use of this method permits one to carry out a biochemical clean-up of wastewater having a caprolactam content up to 600 mg/liter while increasing the oxidative power of the aeration tank by a factor of two.Translated from Khimicheskie Volokna, No. 6, p. 46, November–December, 1985.     

Numerical solution for shape optimization of an impactor penetrating into a semi-infinite target

The shape of the impactor with the maximum depth of penetration (DOP) for a given impact velocity is found using a numerical procedure for solving a corresponding non-classical variational problem. It is shown that the optimum shape in a general case is close to a blunt cone. The variation of the optimal shape of the impactor and the dependence of the DOP vs. the initial (impact) velocity and friction coefficient is studied. The analysis is performed also for optimal conical impactors.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Erosion und Korrosion of metallischer Werkstoffe in feststoffhaltigen Wässern

Erosion and corrosion of metallic materials in particle containing aqueous solutions The combined effect and mutual influence, respectively, of erosion and corrosion of metallic materials in particle containing flows was investigated. Materials under investigation are carbon steel of different hardness levels, ferritic chromium steel, austenitic stainless steel and brass. Corrosive medium was deionized water, acid (pH 4.5), alkaline (pH 10) and chloride (3% NaCl) solution. Quartz particles were used as abrasive at various particle concentrations, grain sizes and flow velocities. For comparison, tests were performed with pure water and under conditions of idle corrosion. Mechanical or corrosive influences dominate depending on material and test conditions, in some cases, synergistic effects of both mechanisms cause an increased mass loss.     

Mechanism of the skeletal isomerisation of linear butenes over ferrierite: analysis of side reactions

An investigation of the effect of reaction conditions on product distribution in the skeletal isomerisation reaction of linear butenes has been carried out. The main reaction routes over ferrierite have been identified. Beside the main product isobutene, major by-product formation occurs. The unwanted reactions include dimerisation of butene to form octenes, hydrogen transfer yielding small amounts of saturated C₃ and C₄ hydrocarbons and disproportionation producing propene and pentenes. The most abundant by-products were pentene and propene, though these were not formed in equimolar amounts as could be expected. Oligomerisation experiments of propene over ferrierite produced large amounts of butene and pentene, revealing the presence of adsorbed nonene. The cracking of this surface species to hexene and propene is the most likely reaction route for the excess propene formation. This additional path to propene formation operates mainly at temperatures above 623 K.     

The Metaflow architecture

The Metaflow architecture, a unified approach to maximizing the performance of superscalar microprocessors, is introduced. The Metaflow architecture exploits inherent instruction-level parallelism in conventional sequential programs by hardware means, without relying on optimizing compilers. It is based on a unified structure, the DRIS (deferred-scheduling, register-renaming instruction shelf), that manages out-of-order execution and most of the attendant problems. Coupling the DRIS with a speculative-execution mechanism that avoids conditional branch stalls results in performance limited only be inherent instruction-level parallelism and available execution resources. Although presented in the context of superscalar machines, the technique is equally applicable to a superpipelined implementation. Lightning, the first implementation of the Metaflow architecture, which executes the Sparc RISC instruction set is described     

Failure loads for notched graphite/epoxy laminates with a softening strip

The strengths of two graphite/epoxy notched laminate systems with a softening strip were investigated. The softening strip was created by replacing the 0°-graphite/epoxy plies by a glass/epoxy composite. Experimental results indicated that the use of softening strips could significantly increase the laminate strength. Analysis was performed with finite elements developed using the classical laminated plate theory and was shown to be adequate. A simple point-stress failure criterion was used to predict the strength of notched laminates with softening strips and the result was found to be satisfactory.     

FMR and EXAFS modeling of heat-treated Fe-rich and Co-rich TM-M thin films

Ion-beam sputter-deposited alloy films of Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ and Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ were examined for their magnetic and structural properties. Films were characterized by ferromagnetic resonance, vibrating sample magnetometry, and extended X-ray absorption fine structure (EXAFS) analysis. Using atomic parameters deduced from EXAFS modeling and fitting procedures, magnetic properties were calculated with no adjustable parameters. Correlation between perpendicular FMR measurements and EXAFS first-shell modeling suggests a low-temperature formation of cobalt-borides in the Co/sub 74/Fe/sub 6/B/sub 15/Si/sub 5/ alloy. Annealed Fe/sub 75/Ni/sub 5/B/sub 15/Si/sub 5/ samples did not display evidence of structural and/or magnetic instabilities until the onset of long-range crystallization near T/sub ann/=400 degrees C.<>