Adaptive viewpoints for co-browsing on heterogeneous devices

Co-browsing is an activity in which a group of users navigate their way through of a set of Web pages together for a shared purpose. Effective co-browsing among users with different device capabilities requires a shared understanding of those Web pages. This paper demonstrates the concept of shared viewpoints (SVPs), and personal viewpoints (PVPs), for co-browsing, before detailing a framework for implementing these concepts. Finally, the effectiveness of the framework is presented through a perceptual experiment.     

On-demand routing and channel assignment in multi-channel mobile ad hoc networks

The capacity of mobile ad hoc networks is constrained by the intra-flow interference introduced by adjacent nodes on the same path, and inter-flow interference generated by nodes from neighboring paths. By assigning orthogonal channels to neighboring nodes, one can minimize both types of interferences and allow concurrent transmissions within the neighborhood, thus improving the throughput and delay performance of the ad hoc network. In this paper, we present three novel distributed channel assignment protocols for multi-channel mobile ad hoc networks. The proposed protocols combine channel assignment with distributed on-demand routing, and only assign channels to active nodes. They are shown to require fewer channels and exhibit lower communication, computation, and storage complexity, compared with existing approaches. Through simulation studies, we show that the proposed protocols can effectively increase throughput and reduce delay, as compared to several existing schemes, thus providing an effective solution to the low capacity problem in multi-hop wireless networks.     

连续时间Sigma-Delta模/数转换器(下)

连续时间∑△调制器 第一枚获业界公认的∑△调制器诞生于1962年,而它事实上是采用了CT电路.此后,利用CT电路来实现∑△调制器便愈来愈普遍,但当开关电容器(SC)电路面世后,大部分的∑△调制器都改以DT环路滤波器来实现.SC电路之所以受欢迎,原因是它不会受信号波形特性的影响.此外,SC积分器的时间常数可随着采样频率而调整,从而提高系统的灵活性.     

用于大面积显示的低成本纳米管场发射显示器

我们验证了一个显示视频图像的阴极阵列,它基于6in对角线、QVGA分辨率的碳纳米管,采用了简单的低成本器件结构。该纳米管是利用选择性化学汽相沉积法生长在特定位置上的,对净化阴极具有良好的可控性。该器件结构只需要三个低分辩率的掩膜工序,开关电压为50V。此外,我们的器件设计为较长的显示寿命创造了条件。在一个较小的全熔接密封的试验显示器上,我们已经记录了超过3000小时的寿命,而电流仅下降了20%。     

Sparse LCMV beamformer design for suppression of ground clutter inairborne radar

Cancellation of the ground clutter received at an airborne phased array radar is an inherently two dimensional problem. Clutter returns are Doppler shifted due to platform motion forcing the use of processors that can resolve targets in both velocity (Doppler) and azimuth. Fully adaptive processors that operate in both dimensions require prohibitively large computation so that reduced adaptive dimension, or partially adaptive processors must be considered. In conventional partially adaptive linearly constrained minimum variance (LCMV) beamformer design the approach taken has been to represent the interference subspace with some reduced set of vectors, typically the eigenvectors associated with the largest eigenvalues of the interference covariance matrix. This technique does yield good performance but will not give the optimum performance for a given partially adaptive dimension. In this paper, an off-line method for selecting the “best” degrees of freedom to be retained in a partially adaptive design is presented. The sequential algorithm described selects those degrees of freedom that best minimize the beamformer output mean square error. This approach leads to a sparse structure for the transformation matrix, which when implemented in a generalized sidelobe canceller (GSC) structure results in a reduction in the computational load. This approach also allows a reduction in the required adaptive dimension as compared to the eigenvector based approach. Illustrative examples demonstrate the effectiveness of this method     

Thickness dependence of stress-induced leakage currents in siliconoxide

The thickness dependence of high-voltage stress-induced leakage currents (SILC's) has been measured in oxides with thicknesses between 5 and 11 nm. The SILC's were shown to be composed of two components: a transient component and a DC component. Both components were due to trap-assisted tunneling processes. The transient component was caused by the tunnel charging and discharging of the stress-generated traps near the two interfaces. The DC component was caused by trap-assisted tunneling completely through the oxide. The thickness, voltage, and trap density dependences of both of these components were measured. The SILC's will affect data retention in electrically erasable programmable read-only memories (EEPROM's) and the DC component was used to estimate to fundamental limitations on oxide thicknesses     

A Finite Element Computational Method for Gas Hydrate. Part I: Theory

A finite element scheme is presented to model the dissociation of gas hydrates in porous media by hot water injection. We show a complete derivation of the finite element formulation, including the associated mass and energy conservation equations capable of performing transient analysis of both conductive and convective heat transfer for gas and liquid flow in porous media. The scheme also includes the latent heat effect to accommodate the change of phase due to melting of hydrate. In the companion paper, Part II, this method is successfully applied to hydrate reservoirs.     

A Finite Element Computational Method for Gas Hydrate. Part II: Application

A finite element model has been applied to the dissociation of gas hydrates in porous media by hot water injection. In the first step, it was applied to calculate the temperature and saturation profiles for a two-phase convective heat transfer case. The second step involved hydrate thawing calculations with release of water and gas. Realistic results were obtained in predicting the temperature, pressure, and water saturation profiles in the hydrate medium with respect to time, when subjected to hot water injection at high pressure in a wellbore. Furthermore, the thaw front progression calculated by this scheme exhibits stable and satisfactory behavior with respect to time.     

Profile-Driven Component Placement for Cluster-Based Online Services

The growth of the Internet and of various intranets has spawned a wealth of online services, most of which are implemented on local-area clusters using remote invocation (for example, remote procedure call/remote method invocation) among manually placed application components. Component placement can be a significant challenge for large-scale services, particularly when application resource needs are workload dependent. Automatic component placement has the potential to maximize overall system throughput. The key idea is to construct (offline) a mapping between input workload and individual-component resource consumption. Such mappings, called component profiles, then support high-performance placement. Preliminary results on an online auction benchmark based on J2EE (Java 2 Platform, Enterprise Edition) suggest that profile-driven tools can identify placements that achieve near-optimal overall throughput.     

Two-dimensional singular vector elements for finite-elementanalysis

The finite-element method (FEM) exhibits a reduced convergence rate when used for the analysis of geometries containing sharp edges where the electromagnetic field is singular. The convergence of the method can be-improved by introducing singular elements that model analytically predicted singular behavior. A number of authors have developed singular elements that are compatible with the scalar FEM. In this paper, we propose a new singular element that is compatible with edge-based vector finite elements and can cope with any order of singularity while preserving the sparsity of the FEM equations. Edge-based singular elements more correctly model singular fields and thus require fewer unknowns, while avoiding the introduction of spurious modes in the numerical solution. Numerical results verify that the convergence of the FEM is significantly improved