Numerical modeling of combustion processes and pollutant formations in direct-injection diesel engines

The Representative Interactive Flamelet (RIF) concept has been applied to numerically simulate the combustion processes and pollutant formation in the direct injection diesel engine. Due to the ability for interactively describing the transient behaviors of local flame structures with CFD solver, the RIF concept has the capabilities to predict the auto-ignition and subsequent flame propagation in the diesel engine combustion chamber as well as to effectively account for the detailed mechanisms of soot formation, NO_X formation including thermal NO path, prompt and nitrous NO_X formation, and reburning process. Special emphasis is given to the turbulent combustion model which properly accounts for vaporization effects on the mixture fraction fluctuations and the pdf model. The results of numerical modeling using the RIF concept are compared with experimental data and with numerical results of the commonly applied procedure which the low-temperature and high-temperature oxidation processes are represented by the Shell ignition model and the eddy dissipation model, respectively. Numerical results indicate that the RIF approach including the vaporization effect on turbulent spray combustion process successfully predicts the ignition delay time and location as well as the pollutant formation.     

A critical heat flux model based on mass, energy, and momentum balance for upflow boiling at low qualities

A mechanistic modeling of critical heat flux (CHF) in upflow boiling at low qualities is performed. The developed model is based on a physical criterion of CHF occurrence and a mechanism limiting the thermal transport between a stagnant bubbly layer and bulk stream. The mechanism can be mathematically formulated by coupling the equation of limiting mixing mass flux, which is derived from momentum balance equations in two regions, with local mass and energy balance equations on the bubbly layer. The resulting form of the model is represented by a general and straightforward CHF formula involving two empirical constants related to the void fraction and the thickness of the bubbly layer. The predictions agree well with the extensive CHF data of water in uniformly heated tubes.     

Magnetic anisotropy of Co-Cr thin films as a function of substrate temperature during deposition

A sequence of Co78Cr22films, 500 nm in thickness, was prepared by deposition on glass in a modified Varian D.C. magnetron S-gun sputtering system. The substrate temperature during deposition, Ts, was fixed at various values with an upper limit of 300°C. Specimens were examined by VSM, TM, FMR and TEM. Msrises significantly with increasing Ts, peaking at 200°C at 370 emu/cm³. The effective volume-averaged anisotropy drops for Ts>110°C from +1.6 KOe to progressively negative values (-4.3 KOe at 300°C). From FMR we find indications of the presence, in addition to the transition and bulk layers, of a highly negative anisotropy constituent (sim-11.5KOe anisotropy field). This resonance appears at Tsvalues of 150°C and above. TEM plane and cross-section views taken on a Ts= 150°C specimen show islands composed of tilted columns within the bulk. For vertical recording, specimens prepared at Tsvalues between 50 and 100°C are recommended. On the other hand, for longitudinal recording applications, films prepared at Tsvalues above 250°C would seem to be appropriate.     

Predicting the performance of concrete structures exposed to chemically aggressive environment—Field validation

The behavior of two series of concrete slabs exposed to sulfate-bearing soils was investigated by a numerical model called STADIUM. In addition to the diffusion of ions and moisture, the model also accounts for the effects of dissolution/precipitation reactions on the transport mechanisms. The simulations yielded by the model were compared to the actual degradation of the slabs after 8 years of exposure. The microstructural alterations of concrete resulting from the penetration of magnesium, chloride and sulfate ions were studied by backscatter mode scanning electron microscope observations and energy-dispersive X-ray analyses. The comparison of both series of data indicates that the model can reliably predict the various features of the microstructural alterations of concrete.

---

Résumé Le comportement de deux séries de dalles sur sol en béton exposées à des sols chimiquement agressifs a été étudié à l'aide d'un code de calcul numérique appelé STADIUM. Ce modèle permet de décrire le transport couplé de l'eau et des ions dans des matériaux poreux non-saturés en prenant en considération l'influence des réactions chimiques. Les résultats des simultations de la dégradation du béton après huit ans d'exposition à des ions chlore, sulfate et magnésium. Les observations ont été réalisées par microscopie électronique à balayage. Des analyses par dispersion des rayons X ont également été effectuées. Les données démontrent clairement que le modèle perment de prédire avec précision le comportement du béton soumis à différents types d'agression chimique.

---

---

Editorial Note Laval University (Canada) is a RILEM Titular Member. Prof. J. Marchand was awarded the 2000 Robert L'Hermite Medal. He is Editor in Chief for Concrete Science and Engineering and Associate Editor for Materials and Structures. He participates in RILEM TC 186-ISA ‘Internal Sulfate attack’.     

Effect of misalignment on electrical characteristics of ACF joints for flip chip on flex applications

The effect of misalignment on the electrical properties of anisotropic conductive film (ACF) joints is investigated in this work. It is found that along with the increase of misalignment, the connection resistance of ACF joints increases. When the misalignment in x-direction is less than 5 μm, the increase rate of connection resistance is quite large. Then, along with the severity of misalignment, the increase rate becomes smaller. Finally, when the misalignment is close to 20 μm, the increase rate rises again. The Holm's electric contact theory is used for understanding the connection resistance variation. On the other hand, with the increase of misalignment in x-direction, the insulation resistance between ACF joints decreases. If the misalignment exceeded 10 μm, the decrease is prominent for the Ni particle ACF joints. This phenomenon can be explained by the effect of dielectric damage of the epoxy.Computer programs are also developed to calculate the variation of the probability of open and shorting after misalignment and predicate the maximum misalignment tolerance. The results show that the open and shorting probability increase abruptly after misalignment. On the view of pad parameters, the open probability is mainly related to the pad area, while the pads gap is critical to the shorting probability. Large pads gap (small pad width) can reduce the shorting probability obviously. On the other hand, enlarging the pad area by increasing pad length decreases the open probability significantly. So comparing to square shape pad, rectangle shape pad can reduce the failure probability greatly.     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

NO emission characteristics in counterflow diffusion flame of blended fuel of H2/CO2/Ar

Flame structure and NO emission characteristics in counterflow diffusion flame of blended fuel of H₂/CO₂/Ar have been numerically simulated with detailed chemistry. The combination of H₂, CO₂ and Ar as fuel is selected to clearly display the contribution of hydrocarbon products to flame structure and NO emission characteristics due to the breakdown of CO₂. A radiative heat loss term is involved to correctly describe the flame dynamics especially at low strain rates. The detailed chemistry adopts the reaction mechanism of GRI 2.11, which consists of 49 species and 279 elementary reactions. All mechanisms including thermal, NO₂, N₂O and Fenimore are taken into account to separately evaluate the effects of CO₂ addition on NO emission characteristics. The increase of added CO₂ quantity causes flame temperature to fall since at high strain rates a diluent effect is prevailing and at low strain rates the breakdown of CO₂ produces relatively populous hydrocarbon products and thus the existence of hydrocarbon products inhibits chain branching. It is also found that the contribution of NO production by N₂O and NO₂ mechanisms are negligible and that thermal mechanism is concentrated on only the reaction zone. As strain rate and CO₂ quantity increase, NO production is remarkably augmented. Copyright © 2002 John Wiley & Sons, Ltd.     

A compact LTCC-based Ku-band transmitter module

Presents design, implementation, and measurement of a three-dimensional (3-D)-deployed RF front-end system-on-package (SOP) in a standard multi-layer low temperature co-fired ceramic (LTCC) technology. A compact 14 GHz GaAs MESFET-based transmitter module integrated with an embedded bandpass filter was built on LTCC 951AT tapes. The up-converter MMIC integrated with a voltage controlled oscillator (VCO) exhibits a measured up-conversion gain of 15 dB and an IIP3 of 15 dBm, while the power amplifier (PA) MMIC shows a measured gain of 31 dB and a 1-dB compression output power of 26 dBm at 14 GHz. Both MMICs were integrated on a compact LTCC module where an embedded front-end band pass filter (BPF) with a measured insertion loss of 3 dB at 14.25 GHz was integrated. The transmitter module is compact in size (400 /spl times/ 310 /spl times/ 35.2 mil/sup 3/), however it demonstrated an overall up-conversion gain of 41 dB, and available data rate of 32 Mbps with adjacent channel power ratio (ACPR) of 42 dB. These results suggest the feasibility of building highly SOP integrated RF front ends for microwave and millimeter wave applications.     

Langmuir-Blodgett deposited cadmium gate inverted InP-GaInAs modulation-doped field-effect transistors

We report on the Langmuir-Blodgett film deposition and plasma etching of cadmium distearate on n-Gao.47Ino.53As to form a high-barrier-height Schottky barrier. Using this technique to form the gate electrode, we fabricated a 1?m-gate-length inverted InP-GalnAs modulation-doped field-effect transistor (MODFET) with an extrinsic transconductance of 170mS/mm and a cutoff frequencyfT of 19 GHz.