Hydrodynamic characteristics of a FCC regenerator

The hydrodynamic and gas mixing characteristics have been determined in a FCC regenerator (0.48 m I.D.x3.4 m high) with FCC particles. Solids holdup in the dense bed decreases with increasing gas velocity, but it increases in the freeboard region. The bubble/void fraction increases with an increase along the bed height at a given gas velocity and increases with increasing gas velocity at a constant bed height. Backmixed tracer gas at the wall region is higher than that at the center region of the bed. The gas backmixing coefficient decreases with increasing gas velocity.     

Study of alinite cement hydration by impedance spectroscopy

Two types of alinite cements, Mg-alinite and Zn-alinite, were synthesized using the reagent grade chemicals. Their hydration behavior was compared with ordinary Portland cement (OPC) using impedance spectroscopy (IS) and ²⁹Si nuclear magnetic resonance (NMR) spectroscopy. The bulk resistance in the IS spectra and the intensity ratio of the hydrous (Q₁ and Q₂) to anhydrous (Q₀) phases in the NMR spectra were estimated as the extent of hydration. The results obtained from both techniques were consistent each other. Mg-alinite had a comparable hydration rate to OPC and Zn-alinite exhibited faster hydration kinetics than Mg-alinite.     

Blends of chlorinated isotactic polypropylene with poly(ethylene-co-vinyl acetate) I. Effect of component polymers composition on the blend miscibility

Chlorinated isotactic polypropylenes (CPP) having various chlorine contents were blended with poly(ethylene-co-vinyl acetate)s (EVA) having various vinyl acetate (VA) contents. The blends were made by casting films from dilute THF solutions and miscibility of the blends was identified by single glass transition temperature, which was confirmed by DSC and dynamic mechanical measurements. Based on the miscibility data from a large number of CPP/EVA combinations, a miscibility map was depicted where CO equivalent weight (CO-EQW) of EVA was plotted against chlorine equivalent weight (Cl-EQW) of CPP. Though an attractive interaction between CPP and EVA could be detected in all the miscible and immiscible blend pairs, miscibility of the CPP/EVA blends could solely be observed in a relatively narrow range of Cl-EQW ca. 65–100 and CO-EQW ca. 170–230.     

The effct of asymmetries of die exit geometry on extrudate swell and melt fracture

Experimental investigations were performed to see how the die exit geometry and the extrusion velocity influence on extrudate swell and melt fracture for several polymer melts [low-density polyethylene, styrene-butadiene rubber (SBR) and SBR/HAF (carbon black) compound]. Four different types of die exit geometry were considered; 0° (symmetric. usual capillary die), and 30°, 45° and 60° (asymmetric dies) were chosen for the die exit angle. Extrudate diameters were measured without draw-down under isothermal condition. Polymer melts were extruded into an oil that has the same density and temperature as those of the extrudate. Extrudate swells from dies with different diameters were correlated with volumetric flow rates. It was observed that the extrudate swell increases with increasing volumetric flow rate and exhibits through a minimum value at about 45° die exit angle. As to the fracture phenomena, it was observed that the critical shear for the onset of melt fracture increases with the increasing die exit angle up to 45°. However, for 60° die exit angle, the onset of melt fracture is again similar to that of 0° exit angle.     

Effect of clinoptilolite addition and solids retention time on the extracellular polymeric substances composition and soluble chemical oxygen demands in activated sludge

This study was carried out to compare EPS (Extracellular Polymeric Substances) composition between conventional activated sludge (AS) and activated sludge dosed with clinoptilolite (CAS). Additionally, those were compared with organic removal efficiency in the effluent in conjunction with EPS concentrations. The experiments were conducted at SRT (Solids Retention Time) ranging from 5 to 100 d. For the CAS, proteins were more readily observed for SRT 20 and 100 d compared to that of the AS. Polysaccharide concentration in the sludge was greatly increased for the CAS, but it was significantly diminished when the SRT was extended. The level of EPS concentration observed from the effluent had the same pattern of variation for the two different types of systems. Regardless of type of reactor, the ratio of proteins for sludge versus effluent was independent of SRT, but the ratio of polysaccharides diminished as SRT increased. In the long run, the degree of protein synthesis directly ascribed to concurrent enhancement of SCOD removal efficiency was slightly more in the CAS. It was decided that clinoptilolite added system could be more reliably retrofitted to a conventional activated sludge process.     

Anisotropically ordered liquid crystalline epoxy network on carbon fiber surface

Summary Anisotropic orientation of liquid crystalline epoxy(LCE) resin on carbon fiber(CF) surface was investigated and it was correlated with curing behavior and thermomechanical properties of LCE. Anisotropic orientation of a LCE resin was spontaneously induced on CF surface along a long molecular axis of CF during curing and the anisotropic orientation was maintained after curing. Curing of LCE was accelerated by alignment of LCE on CF and anisotropic orientation of LCE enhanced dynamic modulus of CF reinforced LCE composites.     

Apparatus for measuring physical adsorption on intact supported porous membranes

We present a non-destructive, reusable apparatus with which to measure physical adsorption isotherms of intact porous membranes. We developed a two-piece sample container to make reliable sorption measurements of porous membranes, the properties of which may differ from those of powders due to crystal intergrowth. This novel system employs a resealable container that can be immersed in a cryogenic bath, into which tubular, planar, or other porous membranes and films may be placed. Detailed sorption isotherms, including high-resolution adsorption in the low pressure (micropore-filling) region, are shown for MFI-type zeolite membranes grown on two types and configurations of α-alumina support.     

Fraktionierung und Charakterisierung von ungehärteten Epoxidharzen aus Bisphenol A und Epichlorhydrin

Gel permeation chromatography and thin layer chromatography have been used respectively to separate and characterize the first seven members of an epoxy resin polymer homologous series on a preparative and analytical scale. The epoxy resin was formed by the reaction between Bisphenol-A and epichlorhydrin. NMR was used to identify the oligomers. The relationship between extinction coefficient and degree of polymerisation was also determined.     

Field bioassay ofexo- andendo-brevicomin withDendroctonus ponderosae in lodgepole pine

Bothexo- andendo-brevicomin reduced the response of flyingDendroctonus ponderosae (Coleoptera: Scolytidae) to an attractant composed oftrans-verbenol and terpenes or oftrans- andcis-verbenol and terpenes in a stand ofPinus contorta var.murrayana. These data suggest that racemicexo- andendo-brevicomin may interrupt aggregation in populations of mountain pine beetle colonizing lodgepole pine; functions of the natural chiral compounds are unknown.Research supported by NSF grants DEB 77-11367 and PCN 79-21708 and the O.S.U. School of Forestry. O.S.U. Agric. Exp. Sta. Tech. Paper No. 5713.     

Synergic influence of a surfactant and ultrasonication on the preparation of soluble,conducting polydiphenylamine/silica‐nanoparticle composites

Conducting polydiphenylamine was used to encapsulate silica nanoparticles through the oxidative polymerization of diphenylamine in the presence of ultrasonic irradiation. The polymerization was performed in the presence of sodium lauryl sulfate as a surfactant. Experiments performed in the absence of ultrasound clearly demonstrated that the application of ultrasonication played multiple roles in the preparation of a composite of polydiphenylamine with silica nanoparticles. Ultrasonication dispersed the silica nanoparticles, converted sodium lauryl sulfate to lauryl alcohol, and augmented the dispersion of the silica‐nanoparticle/polydiphenylamine composite in an organic medium. Silica‐nanoparticle/polydiphenylamine composites were also prepared in the absence of ultrasound and/or sodium lauryl sulfate. The silica‐nanoparticle/polydiphenylamine composites were characterized with Fourier trans form infrared spectroscopy, ultraviolet–visible/near‐infrared spectroscopy, and thermogravimetric analysis. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3912–3918, 2006