The morphology and corrosion resistance of electrodeposited Co‐TiO2 nanocomposite coatings

Co‐TiO₂ nanocomposite coatings with various contents of TiO₂ nanoparticles were prepared by electrodeposition in Co sulfate plating bath containing TiO₂ nanoparticles. The influence of the TiO₂ nanoparticles concentration in the bath, of the current density and of sodium dodecyle sulfate (SDS) as anionic surfactant on the morphology, composition, texture, roughness, and microhardness of the coatings was investigated. The morphology and composition of coatings were studied by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The phase structure of coatings was analyzed by X‐ray diffraction (XRD). The results showed that the maximum codeposition of TiO₂ nanoparticles in Co matrix was around 4.5 vol% obtained in 60 g/L TiO₂ in the bath, 30 mA/cm² and 0.15 g/L SDS. The microhardness of coatings was increased up to 504 Hv by increasing TiO₂ concentration in the bath to 60 g/L TiO₂. The electrochemistry tests including potentiodynamic polarization and impedance spectroscopy revealed that by addition of TiO₂ into Co matrix, the corrosion current density, polarization resistance, and charge transfer resistance of Co‐TiO₂ coating were increased compared with Co coating.     

Influence of Pulse Electrodeposition and Heat Treatment on Microstructure,Tribological, and Corrosion Behavior of Nano-Grain Size Co-W Coatings

In the present study, Co-W nano-structured alloy coatings are produced on low-carbon steel substrate by means of pulse electrodeposition from a citrate-based bath under different average current densities and duty cycles. The results indicate that the coating deposited under 60% of duty cycle and 1 A/dm² of average current density exhibit optimum pulse plating conditions with 44.38 wt.% W, 37 nm grain size, and 758 HV microhardness. The effect of heat treatment temperature on microstructure, composition, corrosion behavior, and morphology of amorphous deposited Co-W alloy with 44 wt.% W was investigated. The microhardness of the coating increased to 1052 HV after heat treatment at 600 °C, which is due to the formation of Co₃W and CoWO₄ phases in the deposit. Furthermore, the coatings heat-treated at 600 °C had lower friction coefficients and better wear resistance under various loads than before heating.     

Exact stability of a platoon of vehicles by considering time delay and lag

The problem of controlling a string of vehicles moving in one dimension is considered so that they all follow a lead vehicle with constant time headway spacing between successive vehicles. Due to realistic design and execution, the negative effect of the tracking lag parameter and time delay is taken into account. By applying an acceleration feedforward, the distance error of each vehicle will be independent of the behavior of other vehicles. As a result, the vehicle is better able to track a desired trajectory, which improves the string stability. Cluster treatment of characteristic roots (CTCR) paradigm is utilized to reveal the stabilizing parametric regions in the domain of the time delay to render the stability of closed loop system. The string stability analysis is performed to evaluate the disturbance attenuation. Finally, an example of multiple vehicle platoon control is presented, which demonstrates the effectiveness of the proposed method.     

Synthesis and characterization of new soluble and thermostable polyimides via novel diisocyanates

A facile synthesis of two novel diisocyanates containing methylene groups and preformed imide structure is described. Furthermore, six thermally stable and soluble polyimides were synthesized by polycondensation of these two diisocyanates with pyromellitic dianhydride (PMDA), 3, 3 ′,4, 4 ′‐benzophenonetetracarboxylic dianhydride (BTDA) and hexafluoroisopropylidene‐2,2‐bis‐(phthalic anhydride) (6FDA) in N,N ‐dimethyl acetamide. All monomers and polymers were characterized by conventional methods and their physical properties such as solution viscosity, solubility properties, thermal stability and thermal behaviour were studied. © 1999 Society of Chemical Industry     

Polyoxometalate–molybdenylacetylacetonate hybrid complex: A reusable and efficient catalyst for oxidation of alkenes with tert-butylhydroperoxide

The hybrid complex consist of molybdenylacetylacetonate complex covalently linked to a lacunary Keggin-type polyoxometalate, K₈[SiW₁₁O₃₉] (POM), was synthesized and characterized by elemental analysis, SEM, XRD, diffuse reflectance UV–Vis and FT-IR spectroscopic methods. The hybrid complex, [MoO₂(acac)–POM] (1), was used for alkene epoxidation with tert-BuOOH in 1,2-dichloroethane as solvent. The complex (1) can catalyze epoxidation of various olefins including non-activated terminal olefins. The effect of reaction parameters such as oxidant, solvent, and temperature on the epoxidation of cyclooctene was also investigated. This heterogeneous catalyst was reused several times in the oxidation of cyclooctene.     

Modified chitosan as a polymeric nanoreactor for fabrication of pure ZnO nano particles

ZnO nanoparticles have been prepared successfully by hydrogel decomposition method (HDM). Synthesized ZnO nanoparticles were characterized by X‐ray diffraction (XRD), fourier transforms infrared spectroscopy (FTIR), and transition electron microscopy (TEM) techniques. Narrow distribution of sizes with a 20–30 nm diameter and regular distribution of ZnO nanoparticles are attributed to the application of poly(acrylic acid‐co‐acrylamide) grafted chitosan hydrogel as coating agent. The results show that the polymer thermal decomposition technique is a perfect method for the synthesis of ZnO nanoparticles. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The effect of ethane on the performance of commercial polyphenylene oxide and Cardo-type polyimide hollow fiber membranes in CO<Subscript>2</Subscript>/CH<Subscript>4</Subscript> separation applications

Impurities such as hydrogen sulfide, water vapor and heavy hydrocarbons in natural gas have considerable effects on the membrane performance. Small amounts of condensable and polymer soluble components in the feed gas cause swelling or plasticization of glassy membranes, leading to a reduction in membrane selectivity. In the present research the influence of ethane was investigated on the permeance and selectivity of two commercially available hollow fiber membranes, namely Cardo-type polyimide and PPO hollow fibers for CO₂/CH₄ separations. It was concluded that the gas mixture permeation rate was increased in the presence of C₂H₆. However, the CO₂/CH₄ separation factors remained almost the same in the presence and absence of the C₂H₆.     

Biologization of Pcl-Mesh Using Platelet Rich Fibrin (Prf) Enhances Its Regenerative Potential In Vitro

Introduction: Resorbable synthetic scaffolds are promising for different indications, especially in the context of bone regeneration. However, they require additional biological components to enhance their osteogenic potential. In addition to different cell types, autologous blood-derived matrices offer many advantages to enhance the regenerative capacity of biomaterials. The present study aimed to analyze whether biologization of a PCL-mesh coated using differently centrifuged Platelet rich fibrin (PRF) matrices will have a positive influence on primary human osteoblasts activity in vitro. A polymeric resorbable scaffold (Osteomesh, Osteopore^TM (OP), Singapore) was combined with differently centrifuged PRF matrices to evaluate the additional influence of this biologization concept on bone regeneration in vitro. Peripheral blood of three healthy donors was used to gain PRF matrices centrifuged either at High (710× g, 8 min) or Low (44× g, 8 min) relative centrifugal force (RCF) according to the low speed centrifugation concept (LSCC). OP-PRF constructs were cultured with pOBs. POBs cultured on the uncoated OP served as a control. After three and seven days of cultivation, cell culture supernatants were collected to analyze the pOBs activity by determining the concentrations of VEGF, TGF-β1, PDGF, OPG, IL-8, and ALP- activity. Immunofluorescence staining was used to evaluate the Osteopontin expression of pOBs. After three days, the group of OP+PRF_Low+pOBs showed significantly higher expression of IL-8, TGF-ß1, PDGF, and VEGF compared to the group of OP+PRF_High+pOBs and OP+pOBs. Similar results were observed on day 7. Moreover, OP+PRF_Low+pOBs exhibited significantly higher activity of ALP compared to OP+PRF_High+pOBs and OP+pOBs. Immunofluorescence staining showed a higher number of pOBs adherent to OP+PRF_Low+pOBs compared to the groups OP+PRF_High+pOBs and OP+pOBs. To the best of our knowledge, this study is the first to investigate the osteoblasts activity when cultured on a PRF-coated PCL-mesh in vitro. The presented results suggest that PRF_Low centrifuged according to LSCC exhibits autologous blood cells and growth factors, seem to have a significant effect on osteogenesis. Thereby, the combination of OP with PRF_Low showed promising results to support bone regeneration. Further in vivo studies are required to verify the results and carry out potential results for clinical translation.     

Salt-assisted solution combustion synthesis of NiFe2O4: Effect of salt type

The effects of three types of salt including NaF, KCl, and NaCl on the properties of NiFe₂O₄ nanoparticles using salt-assisted solution combustion synthesis (SSCS) have been investigated. The synthesized powders were evaluated by SEM, TEM, FTIR, XRD, and VSM analysis. Also, the specific surface area (SSA), as well as size distribution and volume of the porosities of NiFe₂O₄ powders were determined by the BET apparatus. The visual observations showed that the intensity and time of combustion synthesis of nanoparticles have been severely influenced by the type of salt. The highest crystallinity was observed in the synthesized powder using NaCl. The SSA has also been correlated completely to the type of salt. The quantities of SSA was achieved about 91.62, 64.88, and 47.22 m²g^-1 for the powders synthesized by KCl, NaCl, and NaF respectively. Although the magnetic hysteresis loops showed the soft ferromagnetic behavior of the NiFe₂O₄ nanoparticles in all conditions, KCl salt could produce the particles with the least coercivity and remanent magnetization. Based on the present study, the salt type is a key parameter in the SSCS process for the preparation of spinel ferrites. Thermodynamic evaluation also showed that the melting point and heat capacity are important parameters for the proper selection of the salt.     

A comparative study for synthesis methods of nano-structured (9Ni–2Mg–Y) alloy catalysts and effect of the produced alloy on hydrogen desorption properties of MgH2

9Ni–2Mg–Y alloy powders were prepared by arc melting, induction melting, mechanical alloying, solid state reaction and subsequent ball milling processes. The results showed that melting processes are not suitable for preparation of 9Ni–2Mg–Y alloy due to high losses of Mg and Y. Therefore, 9Ni–2Mg–Y alloy powder was prepared by three methods including: 1) mechanical alloying, 2) mechanical alloying + solid state reaction + ball milling, and 3) mixing + solid state reaction + ball milling. The prepared 9Ni–2Mg–Y alloy powders were compared for their catalytic effects on hydrogen desorption of MgH₂. It is found that 9Ni–2Mg–Y alloy powder prepared by mechanical alloying + solid state reaction + ball milling method has a smaller particle size (1–5 μm) and higher surface area (1.7 m² g⁻¹) than that of other methods. H₂ desorption tests revealed that addition of 9Ni–2Mg–Y alloy prepared by mechanical alloying + solid state reaction + ball milling to MgH₂ decreases the hydrogen desorption temperature of MgH₂ from 425 to 210 °C and improves the hydrogen desorption capacity from 0 to 3.5 wt.% at 350 °C during 8 min.