PA-1010/ABS合金的性能研究

研究了以自制的马来酸酐 (MAH)接枝改性ABS(MABS)作为PA 10 10 /ABS增容剂所形成的PA 10 10 /ABS合金的性能。研究结果表明 ,随ABS中马来酸酐接枝量的上升 ,PA 10 10 /ABS合金的冲击强度提高 ,保持PA 10 10与ABS用量在某一恰当配比范围内 ,可得到冲击强度高 ,维卡软化温度较高的合金。     

传热设备自动清洗纽带的开孔结构优化研究

对设有开孔结构的自转清洗纽带进行了传热特性及流阻特性研究。结构优化试验的结果表明 :摩擦阻力和传热强化都随开孔面积比率的增大表现出先上升后下降的趋势 ,传热强化的幅度在 2 %— 18%之间 ,摩擦阻力系数在开孔率 18%时最大 ,其中 7#开孔比率纽带的综合性能最佳。因此 ,这种开孔结构的纽带更宜用于中低Re工况下应用 ,在 2 .0m/s以上的高流速工况下应采用高开孔率结构的纽带或螺旋带     

评“异向双螺杆挤出机的发展前景”一文

本文结合Ｊ．Ｌｅｉｎｇａｒｔｎｅｒ先生的文章，从一个新的角度分析了锥形双螺杆和平行双螺杆挤出机各自的特点，对两种双螺杆挤出机作了评价。     

多核DSP的以太网远程程序加载方法

为了解决工业远程控制设备的软件更新带来的成本和效率问题,在研究了以TMS320C6670为核心的DSP系统的结构和程序启动的基础上,提出了基于以太网的DSP程序远程加载方法。该方法主要基于BOOTP协议的广播和以太网UDP协议实现。实践表明,该加载技术灵活可靠,为远程控制系统的调试和更新提供了便利。     

The tribological behavior of micrometer and nanometer TiO2 particle‐filled poly(phthalazine ether sulfone ketone) composites

Micrometer and nanometer TiO₂ particle‐filled poly(phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions from 0.5 to 7.5 vol % were prepared by heating compression molding. The friction and wear behaviors of the PPESK composites were evaluated using the block‐on‐ring test rig by sliding PPESK‐based composite blocks against a mild carbon steel ring under dry friction conditions. The wear debris and the worn surfaces of the PPESK composites filled with micrometer and nanometer TiO₂ particles were investigated by using a scanning electron microscope (SEM), while the structures of PPESK composites and wear debris were analyzed with IR spectra. Experimental results show that antiwear properties of the PPESK composites can be improved greatly by filling nanometer TiO₂ particles, and the friction coefficient decreases when the filler volume fraction is below 2.5%, but when the filler volume fraction is above 2.5% the friction coefficient increases gradually with increasing filler volume fraction. In the case of micrometer TiO₂ filler, wear rates increase with increasing filler volume fractions under identical test conditions, and the friction coefficients are less sensitive to the filler volume fraction. It was also found that the wear mechanism of micrometer TiO₂ particle‐filled PPESK is mainly severe adhesion and abrasive wear, while that of nanometer TiO₂ particle‐filled PPESK is mainly slight abrasive wear. In the former case, there are no transfer film formed on the surface of the counterpart steel, and wear debris are in the form of long and large ribbon. While in the latter case, the wear debris was granule and their size was about 10 μm. In case of 1 vol % nanometer TiO₂ particle‐filled PPESK composites, the transfer film was fairly thinner and smoother, and the transfer film provided better coverage on the surface of steel ring, while that of 7.5 vol % was thicker and discrete. These account for the different friction and wear behavior of micrometer and nanometer TiO₂ particle‐filled PPESK composite. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 906–914, 2004     

和谐社会视野下的突发环境事件应急立法

日益频发的突发环境事件已成为我国构建社会主义和谐社会的一大障碍。分析《中华人民共和国突发事件应对法》颁布后我国突发环境事件应急立法存在的缺陷与不足,提出了社会主义和谐社会视野下突发环境事件应急立法的完善对策。     

一类特殊本原不可幂定号有向图的广义基

考虑了一类含有三个n—2圈和一个n圈本原不可幂定号有向图的广义基,通过分析图中是否存在寻求的途径及SSSD途径对,运用本原不可幂定号有向图的一些定义和性质,给出了此类图的广义本原指数及广义基.     

底部局部辐射加热窑炉内温度场数值模拟

提出了底部局部辐射加窑炉内温度场数值分析的控制方程组，分别对平面加热及半圆柱形加热面两种算例进行了数值计算，得了影响烤花烤窑炉内温度场均匀性的主要因素和有加热面发射率，加热面形状，加热面相对位置及窑炉墙体热阻和墙体与外界的换热热阻。     

Synthesis and photoconductivity study of phthalocyanine polymers. I. PAA–CuPc(NO2)2

Cu–dinitro–diamino phthalocyanine was synthesized and converted to the diazonium salt. Polyacrylamide bonded CuPc(NO₂)₂ [PAA–CuPc(NO₂)₂] (I) was synthesized by hot polymerization of acrylamide and this diazonium salt. Polymer(I) is water soluble and contains about 7 mol % CuPc(NO₂)₂ rings, which are covalently bonded to PAA. Polymer(I) shows good photoconductivity, which is much better than that of the corresponding phthalocyanine monomers. By doping with iodine (I₂), the photosensitivity of polymer(I) is increased, which through fluorescence analysis is explained by the fact that a charge–transfer complex (CTC) of polymer(I) with I₂ is formed. The influence of interface layer (IFL) and charge–transportation material (CTM) on the photoconductivity of polymer(I) were also studied.