Synthesis and characterization of new aromatic polyimides containing well‐defined conjugation units

A series of aromatic polyimides composed of well‐defined conjugation units were synthesized form 5,5′‐bis(4‐aminophenyl)‐2,2′‐bifuryl (PFDA) and 2,2′‐bis(furyl) benzidine (FurylBZ) with various dianhydrides. The synthesized polyimides emit blue to green light with a quantum yield of 7.3–14.9%, depending on the polymer backbone. In particular, PFDA‐based polymers exhibit extremely narrow photo‐luminescence. The structure, thermal stability, refractive index and dielectric properties of the polymer films were also determined.     

Mechanical, thermal and ablative properties of interply continuous/spun hybrid carbon composites

The mechanical and thermal properties of interply hybrid carbon fiber (continuous and spun fabric)/phenolic composite materials have been studied. Hybrid carbon/phenolic composites (hybrid CP) with continuous carbon fabric of high tensile, flexural strength and spun carbon fabric of better interlaminar shear strength and lower thermal conductivity are investigated in terms of mechanical properties as well as thermal properties.Through hybridization, tensile strength and modulus of spun type carbon fabric reinforced phenolic composites (spun CP) increased by approximately 28% and 20%, respectively. Hybrid CP also exhibits better interlaminar shear strength than continuous carbon fabric/phenolic composites (continuous CP).The in-plane thermal conductivity of hybrid CP is 4-8% lower than that of continuous CP. As continuous filament type carbon fiber volume fraction increases, the transversal thermal conductivity of hybrid CP decreases.The erosion rate and insulation index were examined using torch test. Spun CP has a higher insulation index than continuous CP and hybrid CP over the entire temperature range. Hybrid CP with higher content of spun fabric exhibits higher insulation index as well as lower erosion rate.     

Immobilization of a cyclodextrin glucanotransferase (CGTase) onto polyethylene film with a carboxylic acid group and production of cyclodextrins from corn starch using CGTase‐immobilized PE film

Carboxylic acid groups were introduced onto polyethylene (PE) film by radiation‐induced graft copolymerization. Subsequently, the clodextrin glucanotransferase (CGTase) was immobilized on the PE film with a carboxylic acid group. The activity of the immobilized CGTase on PE film was in the range of 0.40–1.04 U/cm² per min. The production of cyclodextrins (CDs) from corn starch was examined using the CGTase‐immobilized PE film. The production ratios of CDs using CGTase‐immobilized PE film was in the following order: α–CD > β–CD > γ–CD. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2451–2457, 2002     

Manufacturing and foaming of high melt viscosity of polypropylene by using electron beam radiation technology

The high melt viscosity of polypropylene was studied by grafting bifunctional monomers, 1,6‐hexanediol diacrylate (HDDA) and tripropylene glycol diacrylate (TPGDA), onto homopolypropylene (HPP) and random ter‐polypropylene (RTPP) under electron‐beam irradiation. Creation of the high‐melt‐viscosity polypropylene was possible at low radiation dosage and low monomer content, under a prohibition of both radiation degradation and homopolymerization. TPGDA monomer was more effective in increasing the melt viscosity of HPP compared with RTPP, whereas HDDA monomer was more effective for enhancing the melt viscosity of RTPP. Such different effects of monomers on melt viscosity may arise from different monomer structures, namely, TPGDA has additional three methyl groups, but HDDA has no methyl groups. Electron‐beam radiation technology, on an increase of the melt viscosity, was much more effective in HPP than RTPP, when compared with virgin polymers. Modified RTPP and HPP with high melt viscosity were capable of foaming with numerous fine cells, of which the modified HPP with 1.5 mmol TPGDA and 0.5 kGy could create more spherical foam cells and its bending strength was 1.5 times more than that of the foamed RTPP. POLYM. ENG. SCI., 46:431–437, 2006. © 2006 Society of Plastics Engineers.     

Effects of the Addition of Different Types of Fillers on the Properties of BaO–ZnO–B2O3–SiO2 Glass Composites for Application to Barrier Ribs of Plasma Display Panels

Various types of crystalline ceramic fillers (TiO₂, ZrO₂, Al₂O₃, MgO, and cordierite) were added to BaO–ZnO–B₂O₃–SiO₂ (BZBS) glass (5–20 wt%), and the resultant dielectric constant, coefficient of thermal expansion (CTE), and optical reflectance were investigated for the application of the composites to the barrier ribs in plasma display panels. All the investigated fillers were partially dissolved into the glass at the fabrication temperature (575°C), and the residual fillers were aligned along the boundaries of sintered glass frits. By considering all aspects of the properties, the addition of TiO₂ fillers of about 10 wt% to BZBS glass was the most desirable of the types of fillers investigated. The addition of TiO₂ filler (10 wt%) yielded 61% in optical reflectance, 8.3 × 10⁻⁶ K^–1 in coefficient of thermal expansion, and 15.5 in dielectric constant, which were properties comparable with the currently used Pb-based barrier ribs.     

Effect of Antimony Addition on Electrical and Optical Properties of Tin Oxide Film

Antimony-doped tin oxide films were prepared on Corning glass substrate by chemical vapor deposition from a gas mixture of SnCl₄–SbCl₅–H₂O. The electrical conductivity and optical transmission of tin oxide films were studied with antimony doping. The film conductivity increased largely without losing optical transparency with a small addition of antimony. The increase of the conductivity was attributed mainly to more electrons donated by pentavalent Sb ions in the SnO₂ lattice. Large additions of antimony, however, diminished the conductivity, optical transparency, and crystallinity of the film. The diminution was found to be caused by fine Sb₂O₅ phases codeposited with SnO₂.     

Preparation, Microstructure, and Mechanical Properties of Silicon Carbide–Dysprosia Composites

Composites of silicon carbide (SiC) with up to 30 vol% of dysprosia (Dy₂O₃) were fabricated by hot pressing and hot isostatic pressing. The effects of Dy₂O₃ dispersions on the microstructure and on selected mechanical properties of the composites were investigated. When 10-15 vol% of Dy₂O₃ was dispersed in the SiC matrix, the fracture toughness increased by ∼40%, whereas the flexural strength was comparable to that of unreinforced SiC. The increased fracture toughness was due to crack deflection, in conjunction with crack-interface grain bridging, and was not related to a phase transformation of Dy₂O₃ in the matrix.     

Price-based congestion control and local channel-link assignment for multi-radio wireless mesh networks

In multi-radio multi-channel wireless mesh networks, engineering the network capacity requires a complex cross-layer design. In this paper, in order to make the complex problem implementable in a distributed manner, we make a decoupling approach that breaks down the entire design space into routing and initial channel assignment, and distributed congestion control and local channel reassignment. We propose a unified priced-based framework for distributed congestion control and localized channel-link assignment algorithms. We demonstrate the convergence of the proposed algorithms with respect to different fairness objectives (i.e., proportional fairness and max–min fairness) via simulation on both grid and random topologies. The proposed algorithms achieve faster convergence with less overhead in the control and forwarding plane than previous multi-path based algorithms.     

Automatic learners with feedback queries

Automatic classes are classes of languages for which a finite automaton can decide whether a given element is in a set given by its index. The present work studies the learnability of automatic families by automatic learners which, in each round, output a hypothesis and update a long-term memory, depending on the input datum, via an automatic function. Many variants of automatic learners are investigated: where the long-term memory is restricted to be the current hypothesis whenever this exists, cannot be of length larger than the length of the longest datum seen, or has to consist of a constant number of examples seen so far. Learnability is also studied with respect to queries which reveal information about past data or past computation history; the number of queries per round is bounded by a constant.     

Performance evaluation of electrodewatering system for sewage sludges

A laboratory-scale electrodewatering system, incorporating an electric field as an additional driving force to conventional pressure dewatering, has been developed to decrease the water content of sludges generated in wastewater treatment. Consisting of a piston-type filter press, a power supply and a data acquisition system, the electrodewatering system’s performance was evaluated as a function of applied pressure, applied voltage, sludge type and filtration time. Experiments were carried out using sewage sludges with the electric field up to 120 V/cm and pressure ranging from 98.1 to 392.4 kPa. Electrodewatering involving a combination of electric field and pressure enhances both the dewatering rate and final dewatered volume. The final water content of sewage sludges in the electrodewatering system can be reduced to 62 wt%, as compared to 78 wt% achieved with the pressure filtration alone. The electrodewatering system shows the potential to be an effective method for reducing the water content in sludges.