Evaluation of a Method to Measure Black Carbon Particles Suspended in Rainwater and Snow Samples

We conducted a detailed evaluation of a method for measuring the mass concentrations and size distributions of black carbon (BC) particles in rainwater and snow. The method uses an ultrasonic nebulizer (USN) and a single particle soot photometer (SP2). The USN disperses sample water into micron-size droplets at a constant rate and then dries them to release BC particles into the air. The masses of individual BC particles are measured by the SP2, using the laser-induced incandescence technique. The loss of BC particles during the extraction from liquid water to air depends on their sizes. We determined the size-dependent extraction efficiency using polystyrene latex (PSL) spheres with 12 different diameters between 107 and 1025 nm. The PSL concentrations in water were measured by the light extinction at 532 nm. The extraction efficiency of the USN showed a broad maximum of about 10% in the diameter range 200–500 nm and decreased substantially at larger sizes. The accuracy and reproducibility of the measured mass concentration of BC in sample water after long-term storage were about ±25% and ±35%, respectively. We tested the method by analyzing rainwater and surface snow samples collected in Okinawa and Sapporo, respectively. The measured number size distributions of BC in these samples showed negligible contributions of BC particles larger than 300 nm to the total number of BC particles. A dominant fraction of BC mass in these samples was observed in the diameter range 100–500 nm.

Copyright 2013 American Association for Aerosol Research     

Agglomeration Characteristics of Aluminum Particles in AP/AN Composite Propellants

Most solid rockets are powered by ammonium perchlorate (AP) composite propellant including aluminum particles. As aluminized composite propellant burns, aluminum particles agglomerate as large as above 100 μm diameter on the burning surface, which in turn affects propellant combustion characteristics. The development of composite propellants has a long history. Many studies of aluminum particle combustion have been conducted. Optical observations indicate that aluminum particles form agglomerates on the burning surface of aluminized composite propellant. They ignite on leaving the burning surface. Because the temperature gradient in the reaction zone near a burning surface influences the burning rate of a composite propellant, details of aluminum particle agglomeration, agglomerate ignition, and their effects on the temperature gradient must be investigated. In our previous studies, we measured the aluminum particle agglomerate diameter by optical observation and collecting particles. We observed particles on the burning surface, the reaction zone, and the luminous flame zone of an ammonium perchlorate (AP)/ammonium nitrate (AN) composite propellant. We confirmed that agglomeration occurred in the reaction zone and that the agglomerate diameter decreased with increasing the burning rate. In this study, observing aluminum particles in the reaction zone near the burning surface, we investigated the relation between the agglomerates and the burning rate. A decreased burning rate and increased added amount of aluminum particles caused a larger agglomerate diameter. Defining the extent of the distributed aluminum particles before they agglomerate as an agglomerate range, we found that the agglomerate range was constant irrespective of the added amount of aluminum particles. Furthermore, the agglomerate diameter was ascertained from the density of the added amount of aluminum particles in the agglomerate range. We concluded from the heat balance around the burning surface that the product of the agglomerate range and the burning rate was nearly constant irrespective of the added amount of aluminum particles. Moreover, the reduced burning rate increased the agglomerate range.     

Detection of light-absorbing iron oxide particles using a modified single-particle soot photometer

Copyright © 2016 American Association for Aerosol Research     

A New Lead Identification Strategy: Screening an sp3-rich and Lead-like Compound Library Composed of 7-Azanorbornane Derivatives

Although the advantages of sp³-rich, sterically complicated molecules in drug development have been pointed out, modern screening libraries are filled with planar, sp²-rich components. Compounds that are sp³-rich are difficult to synthesize, and thus we aimed to invent an efficient method to construct sp³-rich libraries. By modifying sp³-rich 7-azanorbornane scaffolds through click chemistry, we efficiently prepared a small set of compounds. These compounds were not only sp³-rich, but also had sufficient “lead-like” properties in view of molecular weights and hydrophobicity. Screening assays of this library provided weak κ opioid receptor agonists and growth hormone secretagogue receptor agonists with high hit rates. These results indicate that the 7-azanorbornane scaffold may be a “privileged structure” for lead identification in drug discovery.     

聚丙烯性能试验方法对比研究

选择均聚聚丙烯（PP—H）、抗冲共聚聚丙烯（PP—B）、无规共聚聚丙烯（PP—R）共7个牌号的聚丙烯（PP）产品为研究对象,对比研究了国际标准化组织（简称ISO）制定的标准和美国材料试验协会（简称ASTM）制定的标准对三类PP性能测试的影响。ISO和ASTM2种标准测得的PP产品的拉伸性能、弯曲性能、缺口冲击强度和负荷变形温度存在一定的差异。但2种标准的测试结果具有一定的规律性,这些规律可为今后修订聚丙烯行业和企业标准提供参考。     

Numerical simulation of a polypropylene foam bead expansion process

The production process for expanded polypropylene foam beads (EPP), which consists of steaming, depressurizing, cooling, and ageing operations, was consistently simulated by a set of mathematical models. The models, developed from Yang and Lee's ageing models (Yang and Lee, J. Cell. Plast., 39 , 59 (2003)) for extrusion foam products, were extended in terms of the fundamental aspects of mass and heat transport phenomena. Evaporation and condensation of blowing agents and heat conduction during the steam chest molding and ageing processes were modeled. The governing equations were established by integrating the mass transfer equations of steam and air at the intercellular walls with the constitutive equations of evaporation and condensation in each cell, the equation of heat conduction from the mold to the foam, and the mechanical force balance equation on the cell walls. The models simulate the stress exerted on the steaming chest mold and predict the expansion behavior of cells in the EPP bead‐foam board throughout the ageing process. A sensitivity analysis was also performed by the models to find the key factors which might allow the theoretical determination of the ejection time and shortening of the length of the ageing process. POLYM. ENG. SCI., 48:107–115, 2008. © 2007 Society of Plastics Engineers     

Spatial distribution of silica fillers in phase-separated rubber blends investigated by three-dimensional elemental mapping

The distribution of nano-sized silica in binary rubber blends is characterized by scanning transmission electron microscopy (STEM) tomography combined with energy dispersive X-ray spectrometry (EDX). 3D distribution of silica is visualized by STEM-EDX tomography with the tilt-series of silicon elemental maps, while the phase-separated morphologies of polyisoprene rubber (IR) and styrene-butadiene rubber (SBR) are visualized by STEM-tomography in high-angle-annular-dark field (HAADF) mode. The combination of STEM-EDX and STEM-HAADF tomography enables us to determine the distribution of silica between the two rubber phases quantitatively even with high contents of silica up to 70 phr (weight parts per hundred rubber). It is found that silica is preferentially distributed in the SBR phase, but it is also distributed in the IR phase when the IR fraction in the total rubber components is higher than 40 wt%. The preferential distribution of silica in the SBR phase improves the dispersion of the IR domains. This is the first use of this technique for a multicomponent polymer system, showing the advantage to characterize the complicated multicomponent polymer composite morphologies.     

A Metal-Free,Disulfide Oxidized Form of Superoxide Dismutase 1 as a Primary Misfolded Species with Prion-Like Properties in the Extracellular Environments Surrounding Motor Neuron-Like Cells

Superoxide dismutase 1 (SOD1) is a metalloenzyme with high structural stability, but a lack of Cu and Zn ions decreases its stability and enhances the likelihood of misfolding, which is a pathological hallmark of amyotrophic lateral sclerosis (ALS). A growing body of evidence has demonstrated that misfolded SOD1 has prion-like properties such as transmissibility between cells and intracellular propagation of misfolding of natively folded SOD1. Recently, we found that SOD1 is misfolded in the cerebrospinal fluid of sporadic ALS patients, providing a route by which misfolded SOD1 spreads via the extracellular environment of the central nervous system. Unlike intracellular misfolded SOD1, it is unknown which extracellular misfolded species is most relevant to prion-like properties. Here, we determined a conformational feature of extracellular misfolded SOD1 that is linked to prion-like properties. Using culture media from motor neuron-like cells, NSC-34, extracellular misfolded wild-type, and four ALS-causing SOD1 mutants were characterized as a metal-free, disulfide oxidized form of SOD1 (apo-SOD1^S-S). Extracellular misfolded apo-SOD1^S-S exhibited cell-to-cell transmission from the culture medium to recipient cells as well as intracellular propagation of SOD1 misfolding in recipient cells. Furthermore, culture medium containing misfolded apo-SOD1^S-S exerted cytotoxicity to motor neuron-like cells, which was blocked by removal of misfolded apo-SOD1^S-S from the medium. We conclude that misfolded apo-SOD1^S-S is a primary extracellular species that is linked to prion-like properties.     

Prostaglandin F2alpha increases endothelial nitric oxide synthase in the periphery of the bovine corpus luteum: the possible regulation of blood flow at an early stage of luteolysis

Prostaglandin F(2)(alpha) (PGF(2)(alpha)) released from the uterus causes alterations in luteal blood flow, reduces progesterone secretion, and induces luteolysis in the bovine corpus luteum (CL). We have recently discovered that luteal blood flow in the periphery of the mature CL acutely increases coincidently with pulsatile increases in a metabolite of PGF(2)(alpha) (PGFM). In this study, we characterized changes in regional luteal blood flow together with regional alterations in endothelial nitric oxide synthase (eNOS) expression during spontaneous luteolysis and in response to PGF(2)(alpha). Smooth muscle actin-positive blood vessels larger than 20 microm were observed mainly in the periphery of mature CL. PGF(2)(alpha) receptor was localized to luteal cells and large blood vessels in the periphery of mid-CL. PGF(2)(alpha) acutely stimulated eNOS expression in the periphery but not in the center of mature CL. Injection of the NO donor S-nitroso-N-acetylpenicillamine into CL induced an acute increase in luteal blood flow and shortened the estrous cycle. In contrast, injection of the NOS inhibitor l-NAME into CL completely suppressed the acute increase in luteal blood flow induced by PGF(2)(alpha) and delayed the onset of luteolysis. In conclusion, PGF(2)(alpha) has a site-restricted action depending on not only luteal phase but also the region in the CL. PGF(2)(alpha) stimulates eNOS expression, vasodilation of blood vessels, and increased luteal blood flow in periphery of mature CL. Furthermore, the increased blood flow is mediated by NO, suggesting that the acute increase in peripheral blood flow to CL is one of the first physiological indicators of NO action in response to PGF(2)(alpha).     

Milk-alkali syndrome complicated by acute renal insufficiency]

A case of the "Burnett" syndrome complicated by acute renal insufficiency is reported. Hemodialysis and normalization of the diet helped in the end to eliminate both the milk-alkali syndrome and renal insufficiency.