Gain‐Scheduled Control via Switching of LTI Controllers and State Reset

This paper proposes a synthesis method of gain‐scheduled control systems that switch linear time‐invariant controllers according to hysteresis of the scheduling parameter. Stability and L₂‐gain analysis and synthesis methods for switched systems are applied to the switched gain‐scheduled control synthesis using reset of the controller state, where also the reset law is computed via linear matrix inequalities (LMIs). In addition to optimization of an upper bound of L₂‐gain, we reduce jumps of control input via an auxiliary optimization. Numerical examples are presented to illustrate the switched gain‐scheduled controller.     

DC‐linked hybrid generation system with an energy storage device including photovoltaic generation and gas engine cogeneration for residential houses

For the past few years, hybrid generation systems including solar panel and gas cogeneration have been used for residential houses. Solar panels can generate electronic power at daytime but not at night. But the power consumption of residential houses usually peaks in the evening. The gas engine cogeneration system can generate electronic power without such a restriction, and it also can generate heat power to warm up a house or to produce hot water. In this paper we propose a solar panel and gas engine cogeneration hybrid system with an energy storage device, combined by a DC bus. If a blackout occurs, the system still can supply electronic power for special house loads. We propose a control scheme for the system related to the charging level of the energy storage device and the voltage of the utility grid, which can be applied to both grid‐connected and standalone operation. Finally, we report experiments designed to demonstrate system operation and calculations for loss estimation. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 182(4): 29–46, 2013; Published online in Wiley Online Library ( wileyonlinelibrary.com ).DOI 10.1002/eej.22321     

Highly Sensitive Speech Detector and High-Speed Voiceband Data Discriminator in DSI-ADPCM Systems

This paper describes a highly sensitive speech detector and a high-speed voiceband data classifier capable of discriminating between speech and voiceband data of a 4.8 kbit/s 8-phase PSK and 4.8 kbit/s 8-point QAM, and a 9.6 kbit/s 16-point QAM as described in a CCITT recommendation. The presence of a speech signal is detected by analyzing short-time energies, zero-crossing rates, and sign bit sequences of the input signal. The proposed speech detector, with a short hangover time of 32 ms, is able to reduce the average talk spurt activity in an international satellite link to 36 percent. This detector can also classify the detected speech into narrow-band or wide-band spectrum sounds or a low power sound for a variable rate ADPCM encoding. Discrimination between speech and high-speed voiceband data is based on short-time energies, a zeros-crossing rate and linear prediction coefficients of an adaptive predictor. Classification among a 4.8 kbit/s 8-phase PSK and 8-point QAM, and a 9.6 kbit/s 16-point QAM can also be performed by an average prediction gain and a coefficient of variation of the short-term amplitude distribution of the input signal. Discrimination of voiceband data was performed successfully, and erroneous discrimination of talk spurt of telephone speech as voiceband data were, respectively, four times for two two-party conversations lasting 5 minutes in an international satellite link. This is equivalent to less than 0.09 percent of the conversation time.     

Development of biobased microwave absorbing composites with various magnetic metals and carbons

The preparation and characterization of a biobased electromagnetic absorbing composites derived from natural lacquer as a renewable resource with microwave‐absorption fillers, including Ni–Zn ferrite and carbonyl iron (CI) as magnetic metals and soot and carbon nanotube (CNT) as carbon materials, were investigated in terms of the gel content, hardness, drying properties, and electromagnetic absorption properties. Interestingly, composites with ferrite and CI contained up to 320 and 550 wt %, respectively, of these compounds. This quite high loading capacity of the metal fillers in a natural‐lacquer base could have been due to the high compatibility between the filler and the natural lacquer; this indicated that the natural lacquer worked as a binder for these metals. The morphology of the biobased composite was characterized by scanning electron microscopy. The electromagnetic absorption properties of composites were characterized in the frequency range from 0.05 and 20 GHz by the reflection loss (RL) measurement method in terms of the kind of fillers and filler loading. The natural lacquer did not affect the absorption properties of the fillers. Biobased composites showed over 99% electromagnetic absorption in the frequency range 3.0–4.0 GHz for 280 wt % ferrite and 8.9–9.7 GHz for 200 wt % CI. Conversely, 10 and 20 wt % soot exhibited good performance (RL < ?20 dB) between 16.5 and 17.3 and between 8.8 and 9.2 GHz, respectively. The areas with RL values of less than ?20 dB of the CNT composites were 10.4–11.0 GHz for 5 wt % and 14.6–15.2 GHz for 10 wt %. Hence, natural lacquer can be used as a binder material for electromagnetic absorption composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44131.     

Mechanical properties of interpenetrating polymer network hydrogels based on hybrid ionically and covalently crosslinked networks

Hydrogels are polymer networks swollen in water. Because of their soft and wet nature, and their ability to show large volume changes, hydrogels can be useful in many biomedical and actuator applications. In these applications, it is crucial to tune the mechanical and physical properties of a hydrogel in a controllable manner. Here, interpenetrating polymer networks (IPNs) made of a covalently crosslinked network and an ionically crosslinked network were produced to investigate the effective parameters that control the physical and mechanical properties of an IPN hydrogel. Covalently crosslinked polyacrylamide (PAAm) or poly(acrylic acid) (PAA) networks were produced in the presence of alginate (Alg) that was then ionically crosslinked to produce the IPN hydrogels. The effect of ionic crosslinking, degree of covalent crosslinking, AAm : Alg and AA : Alg ratio on the swelling ratio, tensile properties, indentation modulus, and fracture energy of IPN hydrogels was studied. A hollow cylindrical hydrogel with gradient mechanical properties along its length was developed based on the obtained results. The middle section of this hydrogel was designed as a pH triggered artificial muscle, while each end was formulated to be harder, tougher, and insensitive to pH so as to function as a tendon‐like material securing the gel muscle to its mechanical supports. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2504–2513, 2013     

Observation of the electrorheological effect of siliconeoil/polymer particles suspension

A liquid insulator that suspends small particles is one of the electrorheological fluids (ERF) whose apparent viscosity becomes larger under an electric field because of the formation of particle chains. Since many possible applications of ERF are expected, the development of a more practical ERF is required. We have investigated the ER effect of silicone oil in which small particles are suspended. Silica particles, silica particles coated by conductive polymer film, and polymer particles (microcrystalline cellulose), with a diameter between 5~100 μm, are investigated in order to clarify the difference between suspending materials. To measure the ER effect, a rotational viscometer was constructed. It became clear that the shear stress for cellulose particles is much stronger than that for other particles because of its peculiar particle chain formation due to the particle shape