Development of biobased microwave absorbing composites with various magnetic metals and carbons

The preparation and characterization of a biobased electromagnetic absorbing composites derived from natural lacquer as a renewable resource with microwave‐absorption fillers, including Ni–Zn ferrite and carbonyl iron (CI) as magnetic metals and soot and carbon nanotube (CNT) as carbon materials, were investigated in terms of the gel content, hardness, drying properties, and electromagnetic absorption properties. Interestingly, composites with ferrite and CI contained up to 320 and 550 wt %, respectively, of these compounds. This quite high loading capacity of the metal fillers in a natural‐lacquer base could have been due to the high compatibility between the filler and the natural lacquer; this indicated that the natural lacquer worked as a binder for these metals. The morphology of the biobased composite was characterized by scanning electron microscopy. The electromagnetic absorption properties of composites were characterized in the frequency range from 0.05 and 20 GHz by the reflection loss (RL) measurement method in terms of the kind of fillers and filler loading. The natural lacquer did not affect the absorption properties of the fillers. Biobased composites showed over 99% electromagnetic absorption in the frequency range 3.0–4.0 GHz for 280 wt % ferrite and 8.9–9.7 GHz for 200 wt % CI. Conversely, 10 and 20 wt % soot exhibited good performance (RL < ?20 dB) between 16.5 and 17.3 and between 8.8 and 9.2 GHz, respectively. The areas with RL values of less than ?20 dB of the CNT composites were 10.4–11.0 GHz for 5 wt % and 14.6–15.2 GHz for 10 wt %. Hence, natural lacquer can be used as a binder material for electromagnetic absorption composites. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44131.     

Observation of the electrorheological effect of siliconeoil/polymer particles suspension

A liquid insulator that suspends small particles is one of the electrorheological fluids (ERF) whose apparent viscosity becomes larger under an electric field because of the formation of particle chains. Since many possible applications of ERF are expected, the development of a more practical ERF is required. We have investigated the ER effect of silicone oil in which small particles are suspended. Silica particles, silica particles coated by conductive polymer film, and polymer particles (microcrystalline cellulose), with a diameter between 5~100 μm, are investigated in order to clarify the difference between suspending materials. To measure the ER effect, a rotational viscometer was constructed. It became clear that the shear stress for cellulose particles is much stronger than that for other particles because of its peculiar particle chain formation due to the particle shape     

Highly Sensitive Speech Detector and High-Speed Voiceband Data Discriminator in DSI-ADPCM Systems

This paper describes a highly sensitive speech detector and a high-speed voiceband data classifier capable of discriminating between speech and voiceband data of a 4.8 kbit/s 8-phase PSK and 4.8 kbit/s 8-point QAM, and a 9.6 kbit/s 16-point QAM as described in a CCITT recommendation. The presence of a speech signal is detected by analyzing short-time energies, zero-crossing rates, and sign bit sequences of the input signal. The proposed speech detector, with a short hangover time of 32 ms, is able to reduce the average talk spurt activity in an international satellite link to 36 percent. This detector can also classify the detected speech into narrow-band or wide-band spectrum sounds or a low power sound for a variable rate ADPCM encoding. Discrimination between speech and high-speed voiceband data is based on short-time energies, a zeros-crossing rate and linear prediction coefficients of an adaptive predictor. Classification among a 4.8 kbit/s 8-phase PSK and 8-point QAM, and a 9.6 kbit/s 16-point QAM can also be performed by an average prediction gain and a coefficient of variation of the short-term amplitude distribution of the input signal. Discrimination of voiceband data was performed successfully, and erroneous discrimination of talk spurt of telephone speech as voiceband data were, respectively, four times for two two-party conversations lasting 5 minutes in an international satellite link. This is equivalent to less than 0.09 percent of the conversation time.     

A multilevel PWM strategy suitable for high‐voltage motor direct drive systems with consideration of the adverse effect of dead time

Recently, high‐voltage motor direct drive systems have been put to practical use, and various multilevel PWM strategies have also been proposed. This paper describes a multilevel PWM strategy [our group calls it the Carrier Phase Selection Method (CPS)] that has the lowest line voltage harmonic distortion in order to prevent the degradation of high‐voltage motor winding insulations. This method takes the adverse effect of dead time into consideration, and it controls the shift direction of a carrier phase. Therefore, a favorable output waveform without instantaneous voltage surges is achieved even if the line voltage level changes. Moreover, the switching transitions across all switching devices are well‐balanced, so the utilization of inverter unit cells is equalized. This is an important factor when designing the entire system. Based on simulation and experimental results, it is shown that this CPS method is particularly effective in high‐voltage motor direct drive systems. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 165(2): 77–88, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20474     

Nondestructive Quantitative Evaluation of Porosity Volume Distribution in Aluminum Alloy Die Castings by Fractal Analysis

The nondestructive and three-dimensional quantitative evaluation of porosity in aluminum alloy die castings is proposed to identify whether the predominant cause of pore formation is shrinkage or entrapped gas. The validity of this method of evaluation was shown by comparing two different regions with different ratios of pores formed by shrinkage and gas. It was shown that the proposed evaluation can be used as a quantitative indication of porosity.     

Giant calcifying epithelioma of Malherbe (pilomatrixoma): imaging features

We present a case of giant calcifying epithelioma of Malherbe (pilomatrixoma) in the right upper arm of a 62-year-old man. It measured 18 x 12 x 8 cm in size, making it the largest of all the cases reported previously. CT clearly demonstrated a well-defined, subcutaneous mass with amorphous calcifications. The mass showed intermediate signal intensity on T2*-weighted MR images and slight contrast uptake on contrast-enhanced MR images. Histopathologically, this tumor showed no aggressive or malignant nature. The patient is without evidence of recurrence or metastasis 3 years following the resection.     

Repeatable change in electrical resistance of Si surface by mechanical and electrical nanoprocessing

The properties of mechanically and electrically processed silicon surfaces were evaluated by atomic force microscopy (AFM). Silicon specimens were processed using an electrically conductive diamond tip with and without vibration. After the electrical processing, protuberances were generated and the electric current through the silicon surface decreased because of local anodic oxidation. Grooves were formed by mechanical processing without vibration, and the electric current increased. In contrast, mechanical processing with vibration caused the surface to protuberate and the electrical resistance increased similar to that observed for electrical processing. With sequential processing, the local oxide layer formed by electrical processing can be removed by mechanical processing using the same tip without vibration. Although the electrical resistance is decreased by the mechanical processing without vibration, additional electrical processing on the mechanically processed area further increases the electrical resistance of the surface.