高炉炉渣流动性的实验研究

以宝钢高炉渣中的四大组元(CaO,SiO2,Al2O3,MgO)为基础,实验研究MgO,Al2O3含量及碱度对炉渣的熔化性温度和流动性的影响.结果表明,炉渣中Al2O3含量控制在16%,配制适量的MgO(9%～10%),在1 500℃以上的高温区域,炉渣仍能保持正常的流动性,适合炉缸温度充沛的高炉使用;MgO含量由6%增加到10%时,较明显地降低了炉渣粘度,粘度的递减值约为0.07～0.15 Pa.s.     

纳米NiO粉体的制备及其表征

采用溶胶转化－凝胶法制备了纳米级NiO粉体。Ni(OH)2粉体的TG－DSC分析表明：在升温速率为10℃/min的条件下，粉体在489K时开始显著分解，626K时分解完毕。X－射线衍射分析表明：分解产物为纯净的NiO2。NiO粉体的化学成分分析表明：其纯度高于国家标准。TEM电镜分析表明：NiO粉体呈单分散的球形或棒状颗粒。对NiO粉体的热敏性能有待进一步研究。     

Interaction bounds in multivariable control systems

Time-domain limitations due to right half-plane zeros and poles in linear multivariable control systems are studied. Lower bounds on the interaction are derived. They show not only how the location of zeros and poles are critical in multivariable systems, but also how the zero and pole directions influence the performance. The results are illustrated on the quadruple-tank process, which is a new multivariable laboratory process.     

壳聚糖和粉煤灰对间甲酚的吸附处理

用壳聚糖和粉煤灰对含间甲酚的废水进行吸附处理,考察了壳聚糖的用量、振荡时间、振荡速度以及粉煤灰与壳聚糖的混合比对处理效果的影响.结果表明:在常温下,对于初始质量浓度为56 mg/L的间甲酚,当壳聚糖用量为3 g/L,以170 r/min的转速吸附振荡0.5 h,去除率可达到88%以上;在上述条件下,加入质量比4:1的粉煤灰与壳聚糖混合物5g/L时,间甲酚的去除率可达到91%.     

Hardware and software architecture for power quality analysis

This paper presents a novel concept for power quality hardware and software architecture. Software tools related to detection, classification and characterization of power quality events can be integrated into a Distribution Control Center in which the interconnection between different subsystems is being carried out through the Internet allowing flexibility to the system. This system is implemented using wavelet analysis applied in all proposed algorithms. Different power quality events are taken as examples to illustrate the capabilities of the proposed method. The obtained results reveal that the proposed architecture is feasible to be implemented as an integral part of a control center system.The proposed system has the property of fast and accurate detection and classification of any power quality disturbance event and introduces a new PQ index determination that allows characterizing any type of disturbance including the non-periodic signals.     

Extensions of LDA by PCA mixture model and class-wise features

Linear discriminant analysis (LDA) is a data discrimination technique that seeks transformation to maximize the ratio of the between-class scatter and the within-class scatter. While it has been successfully applied to several applications, it has two limitations, both concerning the underfitting problem. First, it fails to discriminate data with complex distributions since all data in each class are assumed to be distributed in the Gaussian manner. Second, it can lose class-wise information, since it produces only one transformation over the entire range of classes. We propose three extensions of LDA to overcome the above problems. The first extension overcomes the first problem by modelling the within-class scatter using a PCA mixture model that can represent more complex distribution. The second extension overcomes the second problem by taking different transformation for each class in order to provide class-wise features. The third extension combines these two modifications by representing each class in terms of the PCA mixture model and taking different transformation for each mixture component. It is shown that all our proposed extensions of LDA outperform LDA concerning classification errors for synthetic data classification, hand-written digit recognition, and alphabet recognition.     

A tolerant approach to reconstruct topology from unorganized trimmed surfaces

Presented in this paper is a topology reconstruction algorithm from a set of unorganized trimmed surfaces. Error-prone small geometric elements are handled to give proper topological information. It gives complete topology to topologically complete models, and it is also tolerant to incomplete models. The proposed algorithm is vertex-based in that clues for topological information are searched from the set of vertices first, not from that of edges.     

酚醛树脂复合板在热连轧机中的应用

重点分析了现有F7机架出口导卫装置的情况。原导卫材料是由铸钢制造 ,由于摩擦和高温常常引起热连轧带钢表面划伤 ,根据现场实际情况用酚醛树脂复合板替代铸钢导卫装置。实践表明 ,这种改造即可行又可靠 ,并取得了好的效果