Bistatic ISAR images from a time-domain code

Inverse-synthetic-aperture-radar (ISAR) images of radar targets are useful for target identification, visualization, and the analysis of scattering centers. The major advantage of bistatic over monostatic-ISAR imaging is the reduction, in the number of computed incident angles, from hundreds to one. This advantage has already been demonstrated for a physical theory of diffraction (PTD) code, XPATCH. The bistatic-imaging technique can be extended to scattering data obtained from any time-accurate or iterative method, including low-frequency algorithms. This paper presents images from data obtained with a finite-volume time-domain (FVTD) code. It also provides relations between (1) the range and resolution of the bistatic scattering data in the Fourier domain, and (2) the pixel resolution and image extent in the physical domain for the down-range and cross-range directions. A tapering function is applied in the Fourier domain, to dampen ringing effects. Results are shown for a trapezoidal plate, a cone-sphere, and a square-aperture cavity     

1.55-μm polarization-insensitive optical amplifier withstrain-balanced superlattice active layer

A polarization insensitive (sensitivity <1 dB) GaInAs-GaInAsP semiconductor optical amplifier has been realized at 1.55 μm. The active layer consists of a strain-balanced superlattice structure. Gain polarization insensitivity on a large bandwidth (60 nm) together with a 22.5-dB signal gain and a 11-dBm polarization-insensitive saturation output power are obtained     

读书：中国的手机文化

手机，是目前大多数中国人不可或缺的通讯工具。那么，Simon跟大家讲讲手机礼仪。很多人可能不明白，用手机也有礼仪吗？是的，特别是在跟美国人打交道的时候，尤其要注意这点，因为手机在美国的待遇和在中国的待遇是有很大的差别的。     

Interactive simulation of needle insertion models

A novel interactive virtual needle insertion simulation is presented. The simulation models are based on measured planar tissue deformations and needle insertion forces. Since the force-displacement relationship is only of interest along the needle shaft, a condensation technique is shown to reduce the computational complexity of linear simulation models significantly. As the needle penetrates or is withdrawn from the tissue model, the boundary conditions that determine the tissue and needle motion change. Boundary condition and local material coordinate changes are facilitated by fast low-rank matrix updates. A large-strain elastic needle model is coupled to the tissue models to account for needle deflection and bending during simulated insertion. A haptic environment, based on these novel interactive simulation techniques, allows users to manipulate a three-degree-of-freedom virtual needle as it penetrates virtual tissue models, while experiencing steering torques and lateral needle forces through a planar haptic interface.     

用于先进的双嵌入和栓工艺的低缺陷钨CMP高性价比浆料(英文)

介绍了用于钨双嵌入和钨栓CMP工艺的新型CMP3200TM氧化铝浆料,测试证明,这种浆料在110nm技术节点的钨CMP工艺应用中取得了理想的效果。通过对氧化铝粒子制造工艺的有效控制,获得了可满足110nm技术节点双嵌入和栓层钨CMP工艺要求的低缺陷率,高性价比的氧化铝蛐硝酸铁浆料。从而在价格竞争激烈的半导体制造领域,特别是代工市场引起了业界越来越多的关注。     

Real structure of partially ordered crystals

Partial order in crystals is a frequently observed phenomenon in minerals and synthetic materials. The partially ordered structures are characterized by low-dimensional order of the real structure. In the case of 1D structures, the ordered units can be described as rods; 2D structures contain ordered layers. The disorder of the real structures is indicated by prominent diffuse scattering in the diffraction patterns of single crystals. No simple method for the quantitative analysis of the diffuse scattering exists, therefore the determination of essential characteristics of the structures is complicated. However, the determination can be facilitated using a combination of different methods, including electron microscopy, computation and X-ray diffraction.     

Sensor allocation in diverse environments

Sensor coverage varies with location due to factors such as weather, terrain, and obstacles. If a field can be partitioned into zones of homogeneous sensing areas, then the area covered by a random deployment of sensors can be optimized by controlling the number of sensors deployed in each zone. This paper provides formulas to directly calculate the optimal sensor partition in runtime asymptotically equal to the number of zones; to determine the minimum sensor count required to achieve a specific coverage threshold; and to bound the maximum increase in coverage over a strategy oblivious to differences in sensing areas. Results show that this bound is no greater than 13% for a field with two zones. While the analytical solutions assume that each zone is covered independently, sensors are allowed to affect neighboring zones in simulations. Nevertheless, the simulation results support the optimality of the solutions.     

Concept and demonstration of an intermediate band tandem device for solar energy conversion

We have realized a tandem solar cell design that combines a pin‐junction with a photovoltaic intersubband absorber. This concept allows harvesting light in the visible range and the near‐ and mid‐infrared at the same time, and theoretically, energy conversion efficiencies beyond the Shockley–Queisser‐limit could be achieved. A test structure was grown, and the operation of this concept could be confirmed, in principal with an optical two‐beam experiment. The basic characteristics of the device can be explained with an equivalent circuit design that consists of three individual cells, and we find an obvious analogy to the concept of the intermediate band solar cell with noteworthy advantages at some points. Our results show, that for a working device it is crucial to adjust the properties of the photovoltaic intersubband absorber for optimal charge separating performance at the working point of the solar cell. Copyright © 2015 John Wiley & Sons, Ltd.     

How to test graphical user interfaces

An approach for automatically testing GUIs in the MATLAB environment has been proposed. We developed a software tool that tests GUIs by simulating the user through an action recorder. We proposed a heuristic test procedure: providing random input to GUI, but guiding the randomness with predefined weights assigned to the user controls. The weights change during the testing process, as the controls are activated. The errors are collected for later investigation.     

Conventional Electron Microscopy and Electron Holography of Organic Solar Cells

Organic solar cells are a promising route towards large‐area and low‐price photovoltaic systems. The devices are composed of at least two layers: the hole‐transport layer and the electron‐transport layer. The light absorption can occur in one or both layers. At the interface of the layers the excitons are separated into charge carriers, and every layer deals with one type of carrier. Higher efficiencies of the separation process can be obtained by using a mixed layer containing both materials to obtain a very high interface area. Although the structure of the mixed layers used plays a crucial role for the device performance, until now the morphologies have not been elucidated. In order to correlate physical and optical findings with structure and morphology for the materials in question, electron microscopy experiments were performed on the single components as well as on the layer systems. The conventional electron microscope is a poor phase microscope. As consequence, weak‐phase objects like organic molecules have to be stained or imaged under strong defocus to produce an observable contrast. Artifacts caused by chemical staining and the appearance of Fresnel diffraction using the defocus technique represent the main problems of conventional microscopy. These artifacts can be avoided using electron holography. Holograms of ultrathin sections of thin layers composed of organic dye molecules were recorded. Subsequently, the phase images were reconstructed. In this manner, we succeeded in obtaining high‐contrast electron micrographs without applying staining or defocus. In addition, holograms of crystalline C₆₀ and zinc phthalocyanine were successfully recorded. Holography has been shown to be a useful tool to image beam‐sensitive and weak‐phase objects without artifacts.