Flow separation in a viscous parabolic shear past a sphere

Summary Axisymmetric parabolic shear flow past a spinning sphere in an unbounded viscous medium is considered using the matching technique and taking the non-uniform shear as the dominant feature, where the Reynolds number based on parabolic shearR _e 1 and the rotational Reynolds number based on the angular rotation of the sphereR ₀1 are such thatR ₀ ²/R _e =O(1). Forces on the body are calculated and flow separation from the boundary is studied. Coalescion of two wakes or detachment of a wake into two are observed, depending on the increase in magnitudeU of the free stream for a fixedR ₀ ²/R _e or increase inR ₀ ²/R _e for a fixedU respectively.With 8 Figures     

Decoder side Wyner–Ziv frame estimation using Chebyshev polynomial-based FLANN technique for distributed video coding

Multidimensional Systems and Signal Processing - In this paper, a Chebyshev polynomial-based functional link artificial neural network (CFLANN) technique for Wyner–Ziv (WZ) frame estimation...     

Separation of bovine serum albumin (BSA) using γ‐Al2O3–clay composite ultrafiltration membrane

BACKGROUND: Ceramic membranes have received more attention than polymeric membranes for the separation and purification of bio‐products owing to their superior chemical, mechanical and thermal properties. Commercially available ceramic membranes are too expensive. This could be overcome by fabricating membranes using low‐cost raw materials. The aim of this work is to fabricate a low‐cost γ‐Al₂O₃–clay composite membrane and evaluate its potential for the separation of bovine serum albumin (BSA) as a function of pH, feed concentration and applied pressure. To achieve this, the membrane support is prepared using low‐cost clay mixtures instead of very expensive alumina, zirconia and titania materials. The cost of the membrane can be further reduced by preparing a γ‐alumina surface layer on the clay support using boehmite sol synthesized from inexpensive aluminium chloride instead of expensive aluminium alkoxide using a dip‐coating technique. RESULTS: The pore size distribution of the γ‐Al₂O₃‐clay composite membrane varied from 5.4–13.6 nm. The membrane was prepared using stable boehmite sol of narrow particle size distribution and mean particle size 30.9 nm. Scanning electron microscopy confirmed that the surface of the γ‐Al₂O₃–clay composite membrane is defect‐free. The pure water permeability of the support and the composite membrane were found to be 4.838 × 10^?6 and 2.357 × 10^?7 m³ m^?2 s^?1 kPa^?1, respectively. The maximum rejection of BSA protein was found to be 95%. It was observed that the separation performance of the membrane in terms of flux and rejection strongly depends on the electrostatic interaction between the protein and charged membrane. CONCLUSION: The successively prepared γ‐Al₂O₃‐clay composite membrane proved to possess good potential for the separation of BSA with high yield and could be employed as a low cost alternate to expensive ceramic membranes. Copyright © 2009 Society of Chemical Industry     

Electrical reliability aspects of HfO2 high-k gate dielectrics with TaN metal gate electrodes under constant voltage stress

The dielectric breakdown property of ultrathin 2.5 and 5.0 nm hafnium oxide (HfO₂) gate dielectric layers with metal nitride (TaN) gate electrodes for metal oxide semiconductor (MOS) structure has been investigated. Reliability studies were performed with constant voltage stressing to verify the processing condition effects (film thicknesses and post metal annealing temperatures) on times to breakdown. The leakage current characteristics are improved with post metal annealing temperatures (PMA) for both 2.5 and 5.0 nm HfO₂ physical thicknesses. However, it is more prominent (2 orders of magnitudes) for 2.5 nm HfO₂ film thickness. The values of oxide-trapped charge density and interface-state density are also improved for 2.5 nm HfO₂ film. The different stages of charge-trapping behaviors, i.e., stress-induced leakage current, soft and hard breakdown mechanisms have been detected. During constant voltage stress of the MOS capacitors, an increase in the time-dependent gate current is observed, followed by the occurrence of several fluctuations. The amplitude of the fluctuations is much larger in the 5.0 nm HfO₂ gate dielectric layer compared to the 2.5 nm HfO₂ layer. After the occurrence of such fluctuations, the current–voltage characteristics exhibited an increased in gate current compared to the fresh (unstressed) devices.     

Microstructural Analysis of Multi-phase Ultra-Thin Oxide Overgrowth on Al–Mg Alloy by High Resolution Transmission Electron Microscopy

High-resolution transmission electron microscopy analyses are carried out to understand the microstructure of the ultra-thin oxide-film grown on a (native) amorphous Al₂O₃-coated Al-0.8 at.% Mg alloy substrate at T = 600 K for t = 2 h and at pO₂ of 1 × 10^?2 Pa. This oxide-film is found to be non-uniformly thick with thicknesses varying from 1.50 to 4.60 nm. Occasionally, this oxide is found to diffuse into the Al–Mg alloy substrate, forming oxide thicknesses up to 10.5 nm. Overall, this oxide-film is found to consist of a mixed amorphous, (poly) crystalline and an intermediate amorphous-to-crystalline transition regions, with crystalline regions consisting mostly of MgO and the diffused oxide regions into the Al–Mg alloy substrate coated with γ-Al₂O₃. These observations are then compared with the experimental results obtained using angle-resolved X-ray Photoelectron Spectroscopy analysis and thermodynamic predictions for the growth of an ultra-thin oxide-film due to dry, thermal oxidation of Al–Mg alloy substrates.     

Improved automatic tuning of PID controller for stable processes

This paper presents an improved automatic tuning method for stable processes using a modified relay in the presence of static load disturbances and measurement noise. The modified relay consists of a standard relay in series with a PI controller of unity proportional gain. The integral time constant of the PI controller of the modified relay is chosen so as to ensure a minimum loop phase margin of 30. A limit cycle is then obtained using the modified relay. Hereafter, the PID controller is designed using the limit cycle output data. The derivative time constant is obtained by maintaining the above mentioned loop phase margin. Minimizing the distance of Nyquist curve of the loop transfer function from the imaginary axis of the complex plane gives the proportional gain. The integral time constant of the PID controller is set equal to the integral time constant of the PI controller of the modified relay. The effectiveness of the proposed technique is verified by simulation results.     

PI/PID controller design based on IMC and percentage overshoot specification to controller setpoint change

In this work, the normalized Internal Model Control (IMC) filter time constant is designed to achieve a specified value of the maximum sensitivity for stable first and second order plus time delay process models, respectively. Since a particular value of the maximum sensitivity results in an almost constant percentage overshoot to controller setpoint change, an empirical relationship between the normalized IMC filter time constant and percentage overshoot is presented. The main advantage of the proposed method is that only a user-defined overshoot is required to design a PI/PID controller. Simulation examples are given to demonstrate the value of the proposed method.     

Design of a Stable DC Voltage Source and Computer Controlling of It Using an Indigenously Developed All-Digital Addressing-Cum-Control Hardware

We have developed a digitally operated addressing and control module (DACM) for addressing and controlling of equipment from a remote computer using a communication protocol developed in-house. This is useful for automation of an experiment that uses multiple equipment in a pre-decided synchronized manner. We also report design of a multipurpose high voltage direct current (DC) source that provides output of 0–100 V with an average stability of 1.90 (36) mV and has minimum step size of 3 mV. Operation of the DACM is examined by selecting the desired equipment, which in this case is the dc source, and remotely controlling its output from a computer. We also show that this can generate voltage with different waveforms within a 0–10 Hz frequency bandwidth. Such computer controlled ultra-stable high voltage sources tuneable to any arbitrary waveforms at low frequencies have many applications such as, driving a piezo for smooth scanning of laser frequencies, tuning length of a Fabry–Perot cavity, biasing of the electrodes in an ion trap and so on.     

Distributed and robust parameter estimation of IIR systems using incremental particle swarm optimization

In recent years because of substantial use of wireless sensor network the distributed estimation has attracted the attention of many researchers. Two popular learning algorithms: incremental least mean square (ILMS) and diffusion least mean square (DLMS) have been reported for distributed estimation using the data collected from sensor nodes. But these algorithms, being derivative based, have a tendency of providing local minima solution particularly for minimization of multimodal cost function. Hence for problems like distributed parameters estimation of IIR systems, alternative distributed algorithms are required to be developed. Keeping this in view the present paper proposes two population based incremental particle swarm optimization (IPSO) algorithms for estimation of parameters of noisy IIR systems. But the proposed IPSO algorithms provide poor performance when the measured data is contaminated with outliers in the training samples. To alleviate this problem the paper has proposed a robust distributed algorithm (RDIPSO) for IIR system identification task. The simulation results of benchmark IIR systems demonstrate that the proposed algorithms provide excellent identification performance in all cases even when the training samples are contaminated with outliers.