CdTe/CdS thin film solar cells grown in substrate configuration

The ability to grow efficient CdTe/CdS solar cells in substrate configuration would not only allow for the use of non‐transparent and flexible substrates but also enable a better control of junction formation. Yet, the problems of barrier formation at the back contact as well as the formation of a p–n junction with reduced recombination losses have to be solved. In this work, CdTe/CdS solar cells in substrate configuration were developed, and the results on different combinations of back contact materials are presented. The Cu content in the electrical back contact was found to be a crucial parameter for the optimal CdCl₂‐treatment procedure. For Cu‐free cells, two activation treatments were applied, whereas Cu‐containing cells were only treated once after the CdTe deposition. A recrystallization behavior of the CdTe layer upon its activation similar to superstrate configuration was found; however, no CdTe–CdS intermixing could be observed when the layers were treated consecutively. Remarkably high V_OC and fill factor of 768 mV and 68.6%, respectively, were achieved using a combination of MoO₃, Te, and Cu as back contact buffer layer resulting in 11.3% conversion efficiency. With a Cu‐free MoO₃/Te buffer material, a V_OC of 733 mV, a fill factor of 62.3%, and an efficiency of 10.0% were obtained. Copyright © 2012 John Wiley & Sons, Ltd.     

Correcting for contact geometry in Seebeck coefficient measurements of thin film devices

Driven by promising recent results, there has been a revived interest in the thermoelectric properties of organic (semi)conductors. Concomitantly, there is a need to probe the Seebeck coefficient S of modestly conducting materials in thin film geometry. Here we show that geometries that seem desirable from a signal-to-noise perspective may induce systematic errors in the measured value of S, S_m, by a factor 3 or more. The enhancement of S_m by the device geometry is related to competing conduction paths outside the region between the electrodes. We derive a universal scaling curve that allows correcting for this and show that structuring the semiconductor is not needed for the optimal electrode configuration, being a set of narrow, parallel strips.     

Core–Shell Nanoparticle Interface and Wetting Properties

Latex colloids are among the most promising materials for broad thin film applications due to their facile surface functionalization. Yet, the effect of these colloids on chemical film and wetting properties cannot be easily evaluated. At the nanoscale, core–shell particles can deform and coalesce during thermal annealing, yielding fine‐tuned physical properties. Two different core–shell systems (soft and rigid) with identical shells but with chemically different core polymers and core sizes are investigated. The core–shell nanoparticles (NPs) are probed during thermal annealing in order to investigate their behavior as a function of nanostructure size and rigidity. X‐ray scattering allows to follow the re‐arrangement of the NPs and the structural evolution in situ during annealing. Evaluation by real‐space imaging techniques reveals a disappearance of the structural integrity and a loss of NP boundaries. The possibility to fine‐tune the wettability by tuning the core–shell NPs morphology in thin films provides a facile template methodology for repellent surfaces.     

Adhesion and Mechanical Properties of PNIPAM Microgel Films and Their Potential Use as Switchable Cell Culture Substrates

Thermoresponsive poly(N‐isopropylacrylamide) (PNIPAM) microgel films are shown to allow controlled detachment of adsorbed cells via temperature stimuli. Cell response occurs on the timescale of several minutes, is reversible, and allows for harvesting of cells in a mild fashion. The fact that microgels are attached non‐covalently allows using them on a broad variety of (charged) surfaces and is a major advantage as compared to approaches relying on covalent attachment of active films. In the following, the microgels’ physico‐chemical parameters in the adsorbed state and their changes upon temperature variation are studied in order to gain a deeper understanding of the involved phenomena. By means of atomic force microscopy (AFM), the water content, mechanical properties, and adhesion forces of the microgel films are studied as a function of temperature. The analysis shows that these properties change drastically when crossing the critical temperature of the polymer film, which is the basis of the fast cell response upon temperature changes. Furthermore, nanoscale mechanical analysis shows that the films posses a nanoscopic gradient in mechanical properties.     

Growth modes of solution-grown CdS thin films

The growth modes of CdS thin films on glass in a chemical bath were analysed using scanning electron microscopy and optical microscopy. The results of these studies show that the film growth occurs by ion-by-ion condensation and by colloidal particles of CdS adhering to the substrate. Both mechanisms are operative from the initial stages of film growth. The predominance of one or other of these two growth modes depends on the abundance of Cd and S ions present in the solution, which is determined by the amount of complexing and sulphurising agents and ammonia used for the controlled release of Cd and S ions into the solution. The growth mode influences the optical properties of the films.     

A new concept of planar self-reconfigurable modular robot for conveying microparts

Modularity and self-healing are two interesting properties that could help to design more flexible conveyors of micro-objects. In the Smart Blocks project, we propose to design a 2D modular and self-reconfigurable robot composed of centimeter-scale sliding blocks that embed their own actuators and control electronics. This article presents a proof-of-concept of the linkage and of the traveling system as well as an algorithm able to reconfigure a set of blocks from a spatial configuration to another one. Prototype blocks have been realized using electro-permanent magnets which show a good motion speed while saving power consumption during the linkage. Our reconfiguration algorithm is implemented in a simulator software showing in real-time the reconfiguration of the robot.     

Bounded Tamper Resilience: How to Go Beyond the Algebraic Barrier

Related key attacks (RKAs) are powerful cryptanalytic attacks where an adversary can change the secret key and observe the effect of such changes at the output. The state of the art in RKA security protects against an a-priori unbounded number of certain algebraic induced key relations, e.g., affine functions or polynomials of bounded degree. In this work, we show that it is possible to go beyond the algebraic barrier and achieve security against arbitrary key relations, by restricting the number of tampering queries the adversary is allowed to ask for. The latter restriction is necessary in case of arbitrary key relations, as otherwise a generic attack of Gennaro et al. (TCC 2004) shows how to recover the key of almost any cryptographic primitive. We describe our contributions in more detail below. (1) We show that standard ID and signature schemes constructed from a large class of \(\Sigma \)-protocols (including the Okamoto scheme, for instance) are secure even if the adversary can arbitrarily tamper with the prover’s state a bounded number of times and obtain some bounded amount of leakage. Interestingly, for the Okamoto scheme we can allow also independent tampering with the public parameters. (2) We show a bounded tamper and leakage resilient CCA-secure public key cryptosystem based on the DDH assumption. We first define a weaker CCA-like security notion that we can instantiate based on DDH, and then we give a general compiler that yields CCA security with tamper and leakage resilience. This requires a public tamper-proof common reference string. (3) Finally, we explain how to boost bounded tampering and leakage resilience [as in (1) and (2) above] to continuous tampering and leakage resilience, in the so-called floppy model where each user has a personal hardware token (containing leak- and tamper-free information) which can be used to refresh the secret key. We believe that bounded tampering is a meaningful and interesting alternative to avoid known impossibility results and can provide important insights into the security of existing standard cryptographic schemes.     

A Novel Formalism for Partially Defined Asynchronous Feedback Digital Circuits

In contrast to combinational logic and master clocked sequential logical, asynchronous feedback circuits are partially defined due to analogous meta-stabilities. We present a novel formalism to exactly explore this digitally assisted analog phenomenon in order to build up a representative test bench that is able to enforce race constraints (meta-stable behavior) for non-deterministics, instabilities as well as for oscillations in feedback structures. Further, we introduce our definitions for consistently modeling under state transition graphs, we provide all entities for modeling asynchronous feedback structures and state our proposed methodology with an exemplary asynchronous circuitry. The given example is explained at a high level of abstraction, all data for revision is provided, too. The approach seems to be capable to test for meta-stabilities, analog behavior in feedback digital structures.     

Gyroid‐Structured 3D ZnO Networks Made by Atomic Layer Deposition

3D continuous ZnO morphologies with characteristic feature sizes on the 10 nm length scale are attractive for electronic device manufacture. However, their synthesis remains a challenge because of the low crystallization temperature of ZnO. Here, we report a method for the robust and reliable synthesis of fully crystalline 3D mesoporous ZnO networks by means of atomic layer deposition (ALD) of ZnO into a self‐assembled block copolymer template. By carefully optimizing the processing conditions we are able to synthesize several‐micrometer‐thick layers of mesoporous ZnO networks with a strut width of 30 nm. Two 3D mesoporous morphologies are manufactured: a periodic gyroid structure and a random worm‐like morphology. Exploiting the ALD property to conformally coat complex surfaces of high aspect ratio, the channel network of a 3D continuous channel network of a self‐assembled block copolymer is replicated into ZnO. X‐ray photoemission spectroscopy and x‐ray diffraction measurements reveal that the chemical composition of the mesoporous structures is uniform and consists of wurtzite‐ZnO throughout the film. Scanning electron microscopy reveals an average pore dimension of 30 nm. The potential of this material for a hybrid photovoltaic application is demonstrated by the manufacture of a poly(3‐hexylthiophene)/ZnO solar cell.     

ZnCdS films for solar cell and photodetector applications deposited by In Situ chemical doping of CdS with Zn

ZnCdS films were formed by in situ chemical doping of CdS with Zn in a chemical bath. The X-ray diffraction (XRD) patterns of CdS films after Zn doping showed a more disordered nature, consisting of reflections from Zn_0.049Cd_0.951S (JCPDS 40-834) as well as CdS greenockite (hexagonal, JCPDS 41-1049) and hawleyite (cubic, JCPDS 10-0454) phases. A comparison of the optical transmittance spectra for undoped and Zn-doped films showed that the cut-off wavelength was modified after Zn doping, indicating the presence of impurity states in the band gap. Zn-doped films showed an increase in dark conductivity after annealing at about 200°C. These films exhibit promising characteristics for application in solar cell and photodetector structures.